ECO mode NISSAN 350Z 2007 Z33 Body Control System Workshop Manual

BCM (BODY CONTROL MODULE)
BCS-7
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: 2006 November2007 350Z
BCM STATUS CONTROL
BCM changes its status depending on the operation status in order to save power consumption.
1. CAN communication status

With ignition switch ON, CAN communicates with other control units normally.

Control by BCM is being operated properly.

When ignition switch is OFF, switching to sleep mode is possible.

Even when ignition switch is OFF, if CAN communication with IPDM E/R and combination meter is
active, CAN communication status is active.
2. Sleep transient status

This status shuts down CAN communication when ignition switch is turned OFF.

It transmits sleep request signal to IPDM E/R and combination meter.

Two seconds after CAN communication of all control units stops, sleep transient status switches to CAN
communication inactive status.
3. CAN communication inactive status

With ignition switch OFF, CAN communication is not active.

With ignition switch OFF, control performed only by BCM is active.

Three seconds after CAN communication of all control units stops, CAN communication inactive status
switches to sleep status.
4. Sleep status

BCM is activated with low power mode.

CAN communication is not active.

When CAN communication operation is detected, it switches to CAN communication status.

When a state of the following switches changes, it switches to CAN communication state.
–Key switch (ACC, ON)
–Hazard switch
–Door lock/unlock switch
–Front door switch (driver side, passenger side)
–Back door opener switch (coupe models)
–Trunk lid opener switch (roadster models)
–Combination switch (passing, lighting switch 1ST position)
–Key fob (lock/unlock signal)
–Key cylinder switch

When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.

Status of combination switch reading function is changed.

BCM (BODY CONTROL MODULE)
BCS-15
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: 2006 November2007 350Z
CONSULT-III Function (BCM)NKS0009R
CONSULT-III can display each diagnostic item using the diagnostic test mode shown following.
ITEMS OF EACH PART
NOTE:
CONSULT-III displays systems equipped in the vehicle.
×: Applicable
NOTE:
This item is displayed, but should not be used.BCM diagnostic test item Check item, diagnostic test mode Content
Inspection by partWORK SUPPORT Changes setting of each function.
SELF-DIAG RESULTS BCM performs self-diagnosis of CAN communication.
DATA MONITOR Displays the input data of BCM in real time.
ACTIVE TEST Gives a drive signal to a load to check the operation.
CAN DIAG SUPPORT MNTRThe result of transmit/receive diagnosis of CAN com-
munication can be read.
ECU PART NUMBER BCM part number can be read.
System and item CONSULT-III displayDiagnostic test mode (Inspection by part)
WORK
SUPPORTSELF−
DIAG
RESULTSDATA
MONI-
TORCAN
DIAG
SUP-
PORT
MNTRACTIVE
TESTECU
PA RT
NUM-
BERCON-
FIGU-
RATION
BCM BCM×× × ×
×
NOTE
Power door lock system DOOR LOCK×××
Rear window defogger REAR DEFOGGER××
Warning chime BUZZER××
Room lamp timer INT LAMP×××
Remotecontrol entry system MULTI REMOTE ENT×××
Headlamp HEAD LAMP×××
Wiper WIPER×××
Turn signal lamp
Hazard lampFLASHER××
Blower fan switch signal
A/C switch signalAIR CONDITONER×
Combination switch COMB SW×
NVIS IMMU××
Interior lamp battery saver BATTERY SAVER×× ×
Trunk lid TRUNK××
Vehicle security system THEFT ALM×××
Retained power control RETAINED PWR×××
Oil pressure switch SIGNAL BUFFER
×
NOTE×
Low tire pressure warning
system AIR PRESSURE
MONITOR××× ×
Panic alarm system PANIC ALARM×