ignition NISSAN 350Z 2007 Z33 Body, Lock And Security System User Guide

BL-46
POWER DOOR LOCK SYSTEM
Revision: 2006 November2007 350Z
Check Passenger Side Door Lock Actuator NIS0000U
1. CHECK DOOR LOCK ACTUATOR SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between passenger side door lock actuator connector and ground.
OK or NG
OK >> GO TO 2.
NG >> Replace BCM.
2. CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector M91 terminals 50, 51 and passenger side door lock
actuator harness connector D40 terminals 1, 3.
3. Check continuity between BCM harness connector M91 termi-
nals 50, 51 and ground.
OK or NG
OK >> Replace passenger side door lock actuator.
NG >> Repair or replace harness between BCM and passenger side door lock actuator.
ConnectorTerminal
(Wire color)
ConditionVoltage (V)
(Approx.)
(+) (–)
M9150 (PU)
GroundDoor lock/unlock switch
is turned to LOCK.0 →Battery
voltage→ 0
51 (W/R)Door lock/unlock switch
is turned to UNLOCK.0 →Battery
voltage→ 0
PIIA6385E
50 (PU) – 1 (PU) : Continuity should exist.
51 (W/R) – 3 (GY) : Continuity should exist.
50 (PU) – Ground : Continuity should not exist.
51 (W/R) – Ground : Continuity should not exist.
PIIB3790E

POWER DOOR LOCK SYSTEM
BL-47
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Check Door Key Cylinder Switch NIS0000V
1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
With CONSULT-III

Check door key cylinder switch (“KEY CYL LK SW”) in “DATA MONITOR” mode with CONSULT-III.

Check door key cylinder switch (“KEY CYL UN-SW”) in “DATA MONITOR” mode with CONSULT-III.
Without CONSULT-III
Check voltage between power window main switch (door lock and unlock switch) connector and ground.
OK or NG
OK >> Further inspection is necessary. Refer to symptom
chart.
NG >> GO TO 2.
2. CHECK DOOR KEY CYLINDER SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window main switch (door lock and unlock switch) and door key cylinder switch con-
nector.
3. Check continuity between power window main switch (door lock and unlock switch) harness connector D7
terminals 6, 7 and door key cylinder switch harness connector D12 terminals 1, 3.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness between power window main
switch and door key cylinder switch. “KEY CYL LK-SW” should be “ON” when key inserted
in door key cylinder is turned to lock.
“KEY CYL UN-SW” should be “ON” when key inserted
in door key cylinder is turned to unlock.
ConnectorTe r m i n a l s
Key position Voltage (V)
(Approx.)
(+) (–)
D76 (B/R)
GroundNeutral/Unlock 5
Lock 0
7 (SB)Neutral/Lock 5
Unlock 0
PIIA3352E
6 (B/R) – 3 (B/R) : Continuity should exist.
7 (SB) – 1 (SB) : Continuity should exist.
PIIA3353E

POWER DOOR LOCK SYSTEM
BL-49
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
2. CHECK BACK DOOR OPENER SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM and back door opener switch connector.
3. Check continuity between BCM harness connector M90 terminal 30 and back door opener switch harness
connector T103 terminal 1.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness between BCM and back door
opener switch.
3. CHECK BACK DOOR OPENER SWITCH
Check continuity between back door opener switch terminals 1 and 2.
OK or NG
OK >> GO TO 4.
NG >> Replace back door opener switch.
4. CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect driver side door lock actuator connector.
2. Check continuity between back door opener switch harness connector T103 terminal 2 and driver side
door lock actuator harness connector D11 terminal 2.
OK or NG
OK >> GO TO 5.
NG >> Repair or replace harness between back door opener
switch and driver side door lock actuator. 30 (P) – 1 (P) : Continuity should exist.
PIIB3791E
Connector Terminals Condition Continuity
T103 1 2Back door opener switch: ON Yes
Back door opener switch: OFF No
PIIA2349E
2 (G) – 2 (OR) : Continuity should exist.
PIIA2348E

BL-50
POWER DOOR LOCK SYSTEM
Revision: 2006 November2007 350Z
5. CHECK DOOR LOCK ACTUATOR GROUND CIRCUIT
Check continuity between driver side door lock actuator harness connector D11 terminal 4 and ground.
OK or NG
OK >> Replace driver side door lock actuator.
NG >> Repair or replace harness.
Check Back Door Opener Actuator NIS0000X
1. CHECK BACK DOOR OPENER ACTUATOR SIGNAL
Check voltage between BCM connector and ground.
Press the back door opener switch when driver side door is
unlocked.
OK or NG
OK >> GO TO 2.
NG >> Replace BCM.
2. CHECK BACK DOOR OPENER ACTUATOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM and back door opener actuator connector.
3. Check continuity between BCM harness connector B83 terminal 68 and back door opener actuator har-
ness connector T11 terminal 1.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness between BCM and back door
opener actuator. 4 (B) – Ground : Continuity should exist.
PIIA2347E
ConnectorTerminals
(Wire color)
Condition Voltage (V)
(Approx.)
(+) (–)
B83 68 (L/R) GroundBack door
opener switch
ONBattery
voltage
Back door
opener switch
OFF0
PIIB1270E
68 (L/R) – 1 (L/R) : Continuity should exist.
PIIB1263E

BL-52
FUEL FILLER LID OPENER
Revision: 2006 November2007 350Z
FUEL FILLER LID OPENERPFP:78820
System Description/For RoadSterNIS0000Y
Power is supplied at all times

through 40A fusible link (letter F , located in the fuse and fusible link box)

to BCM terminal 55,

through 10A fuse [No.18, located in the fuse block (J/B)]

to BCM terminal 42.
When ignition switch ACC or ON position, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to BCM terminal 11.
Ground is supplied

to BCM terminal 52

through body grounds M30 and M66.
FUEL LID OPEN OPERATION
When fuel lid opener switch is ON (pushed), ground is supplied

to BCM terminal 58

through fuel lid opener switch terminals 1 and 2, and

through body grounds M30 and M66.
And power is supplied

to BCM terminal 70

through fuel lid opener actuator terminals 1 and 2, and

through body grounds B5, B6, and T14.
Then fuel lid opener actuator opens fuel lid.
FUEL LID OPENER CANCEL OPERATION
Fuel lid cannot open when vehicle condition is in arm or alarm phase.

BL-56
FUEL FILLER LID OPENER
Revision: 2006 November2007 350Z
Terminals and Reference Value for BCM/For RoadsterNIS00012
Trouble Diagnosis/For RoadsterNIS00013
FUEL LID DOSE NOT OPEN WITH FUEL LID OPENER SWITCH
1. VEHICLE CONDITION
Check vehicle security system.
Ye s o r N o
Yes >> Cancel arm phase or alarm phase condition.
No >> GO TO 2.
2. CHECK FUEL LID OPEN INPUT SIGNAL
With CONSULT-III
Check door switches (“F/LID OPN SW”) in “DATA MONITOR” mode with CONSULT-III.
Without CONSULT-III
1. Turn ignition switch OFF.
2. Check voltage between BCM and ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 6.
Termi-
nalWire
colorItemSignal
Input/
OutputConditionVoltage [V]
(Approx.)
11 LG Ignition switch (ACC) Input Ignition switch (ACC or ON) Battery voltage
39 L CAN-H Input — —
40 P CAN-L Input — —
42 GY Power source (Fuse) Input — Battery voltage
52 B Ground — — 0
55 R Power source (Fusible link) Input — Battery voltage
58 Y/B Fuel lid opener switch InputFuel lid opener switch is ON 0
Fuel lid opener switch is OFF Battery voltage
70 W/LFuel lid opener release
output signalOutputFuel lid opener switch is ON 0
Fuel lid opener switch is OFFBattery voltage
(For 0.5s)
Arm phase or alarm phase?
Monitor item Condition
F/LID OPN SWOPEN : ON
CLOSE : OFF
ConnectorTerminal
(Wire color)
ConditionVoltage [V]
(Approx.)
(+) (–)
B83 58 (Y/B) GroundFuel lid opener switch ON 0
Fuel lid opener switch OFF Battery voltage
PIIB1259E

REMOTE KEYLESS ENTRY SYSTEM
BL-61
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
System DescriptionNIS00015
INPUTS
Power is supplied at all times

through 40A fusible link (letter F , located in the fuse and fusible link box)

to BCM terminal 55,

through 10A fuse [No.18, located in the fuse block (J/B)]

to BCM terminal 42,

through 10A fuse [No. 21, located in the fuse block (J/B)]

to key switch terminal 2.
When the ignition switch is ON or START position, power is supplied

through 10A fuse [No.1, located in the fuse block (J/B)]

to BCM terminal 38.
When the ignition switch is ACC or ON position, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to BCM terminal 11.
Ground is supplied

to BCM terminal 52

through body grounds M30 and M66.
When the driver side door switch is ON (door is OPEN), ground is supplied

to BCM terminal 62

through driver side door switch terminal 1 and

through driver door switch case ground.
When the passenger side door switch is ON (door is OPEN), ground is supplied

to BCM terminal 12

through passenger side door switch terminal 1 and

through passenger side door switch case ground.
When the back door switch (For coupe models) is ON (door is OPEN), ground is supplied

to BCM terminal 58

through the back door switch terminals 1 and 3 and

through body grounds B5, B6, D105 and T14.
When the trunk lid lock assembly (trunk room lamp switch) (For roadster models) is ON (trunk is OPEN),
ground is supplied

to BCM terminal 57

through the trunk room lamp switch terminals 3 and 1 and

through body grounds B5,B6 and T14.
When the key switch is ON (key is inserted in ignition key cylinder), power is supplied

through key switch terminals 2 and 1

to BCM terminal 37.
Key fob signal is inputted to remote keyless entry receiver (the antenna of the system is built in remote keyless
entry receiver).
Remote keyless entry receiver sends keyfob signal

to BCM terminal 20

from remote keyless entry receiver terminal 2.
The remote keyless entry system controls operation of the

power door lock

hazard and horn reminder

auto door lock

interior lamp and step lamp

panic alarm

REMOTE KEYLESS ENTRY SYSTEM
BL-63
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Interior Lamp and Step Lamp Operation
When the following conditions come:

condition of interior lamp switch is DOOR position;

door switch OFF (when all the doors are closed);
Remote keyless entry system turns on interior lamp (for 30 seconds) with input of UNLOCK signal from key
fob.
For detailed description, refer to LT- 1 3 0 , "
MAP LAMP TIMER OPERATION" .
Panic Alarm Operation
When key switch is OFF (when ignition key is not inserted in key cylinder), BCM turns on and off horn and
headlamp intermittently with input of PANIC ALARM signal from key fob.
The alarm automatically turns off after 25 seconds or when BCM receives any signal from key fob.
For detailed description, refer to BL-128, "
PANIC ALARM OPERATION" .
Back Door Operation/For Coupe
When a BACK DOOR OPEN signal is sent with key OFF (ignition key removed from key cylinder) from key
fob, power is supplied through BCM terminal 19.
When power and ground are supplied, back door opener actuator opens back door.
Trunk Opener Operation/For Roadster
When a TRUNK OPEN signal is sent with key OFF (ignition key removed from key cylinder) from key fob,
power is supplied through BCM terminal 19.
When power and ground are supplied, trunk lid opener actuator opens trunk.
Keyless Power Window Down (open) Operation
When key fob unlock switch is turned ON with ignition switch OFF, and key fob unlock switch is detected to be
on continuously for 3 seconds, the driver's door and passenger's door power windows are simultaneously
opened.
Power window is operated to open and the operation continues as long as the key fob unlock switch is
pressed.
CAN Communication System DescriptionNIS00016
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitNIS00017
Refer to LAN-4, "CAN Communication System"

REMOTE KEYLESS ENTRY SYSTEM
BL-71
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Terminals and Reference Value for BCMNIS0001B
*1: When interior lamp battery saver control is in OFF: Approx 5V.
*2: For roadster.Te r -
minal Wire
colorItemSignal
input/
outputConditionVoltage (V)
(Approx.)
11 LG Ignition switch (ACC) Input Ignition switch (ACC or ON position) Battery voltage
12 P Passenger side door switch Input ON (Open) → OFF (Closed) 0 → 5
18 BRemote keyless entry
receiver (Ground)—— 0
19 YRemote keyless entry
receiver (Power supply)OutputKey is inserted in IGN key cylinder 0
All door closed
20 LRemote keyless entry
receiver (Signal)InputKey is inserted in IGN key cylinder 0
Waiting
(All door closed)
When signal is received
(All door closed)
37 B/R Key switch (Insert) InputON (Key inserted) → OFF (Key
removed from IGN key cylinder)Battery voltage → 0
38 W/L Ignition switch (ON) Input Ignition switch (ON or START position) Battery voltage
39 L CAN – HInput/
Output——
40 P CAN – LInput/
Output——
42 GY Power source (Fuse) Input — Battery voltage
52 B Ground — — 0
55 R Power source (Fusible link) Input — Battery voltage
57 R/WTrunk lid lock assembly
(trunk room lamp switch)*
2Input
ON (Open) → OFF (Closed)
0 → Battery voltage*1
58 R/W Back door switch Input
62 L Driver side door switch Input ON (Open) → OFF (Closed) 0 → 5
OCC3881D
OCC3879D
OCC3880D

REMOTE KEYLESS ENTRY SYSTEM
BL-73
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
CONSULT-III Application Items for BCMNIS0001F
“MULTI REMOTE CONTENT”
Work Support
Hazard and horn reminder mode
Auto door lock operation mode
Panic alarm operation mode
Back door open operation mode
Trunk lid open operation mode (Roadster models)
Power window down (open) operation mode
Data Monitor
Test Item Description
REMO CONT ID CONFIR It can be checked whether key fob ID code is registered or not in this mode.
REMO CONT ID REGIST Key fob ID code can be registered.
REMO CONT ID ERASUR Key fob ID code can be erased.
MULTI ANSWER BACK SETHazard and horn reminder mode can be changed in this mode. The reminder mode will be changed
when “MODE SET” on CONSULT-III screen is touched.
AUTO LOCK SETAuto locking function mode can be changed in this mode. The function mode will be changed when
“MODE SET” on CONSULT-III screen is touched.
PANIC ALRM SETPanic alarm operation mode can be changed in this mode. The operation mode will be changed
when “MODE SET” on CONSULT-III screen is touched.
TRUNK OPEN SETBack door opener operation mode can be changed in this mode. The operation mode will be
changed when “MODE SET” on CONSULT-III screen is touched.
Trunk lid opener operation mode can be changed in this mode. The operation mode will be changed
when “MODE SET” on CONSULT-III screen is touched.
PW DOWN SETKeyless power window down (open) operation mode can be changed in this mode. The operation
mode will be changed when“MODE SET” on CONSULT-III screen is touched.
ON
(C mode)OFF
(S mode)MODE 3 MODE 4 MODE 5 MODE 6
Key fob
operation Lock Unlock Lock Unlock Lock Unlock Lock Unlock Lock Unlock Lock Unlock
Hazard warning
lamp flashTwice Once Twice — — — Twice Once Twice — — Once
Horn sound Once———————Once—Once—
MODE 1 MODE 2 MODE 3
Auto locking function 1 minutes Nothing 5 minutes
MODE 1 MODE 2 MODE 3
Key fob operation 0.5 seconds Nothing 1.5 seconds
MODE 1 MODE 2 MODE 3
Key fob operation 0.5 seconds Nothing 1.5 seconds
MODE 1 MODE 2 MODE 3
Key fob operation 0.5 seconds Nothing 1.5 seconds
MODE 1MODE 2MODE 3
Key fob operation 3 seconds Nothing 5 seconds
Monitored Item Description
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position.