key fob NISSAN 350Z 2007 Z33 Body, Lock And Security System User Guide

BL-76
REMOTE KEYLESS ENTRY SYSTEM
Revision: 2006 November2007 350Z
Trunk does not open when trunk opener button is
continuously pressed. (Roadster models)1. Check trunk opener operation BL-114
2. Check trunk open operation mode BL-73
3. Check key fob battery and function BL-77
4. Check key switch BL-84
5. Replace BCMBCS-17
Hazard reminder does not activate properly when
pressing lock or unlock button of key fob.1. Check hazard reminder mode *
*: Hazard reminder can be activated or deactivated. First check
the hazard reminder setting.BL-732. Check hazard warning lamp function with hazard switch.LT- 6 6
3. Check door switch BL-79
4. Replace BCMBCS-17
Horn reminder does not activate properly when
pressing lock button of key fob.1. Check horn reminder mode *
*: Horn reminder can be activated or deactivated. First check the
horn chirp setting.BL-732. Check horn chirp function with horn switch.BL-88
3. Check door switch BL-79
4. Check IPDM E/R operation BL-85
5. Replace BCMBCS-17
Interior lamp and step lamp operation do not acti-
vate properly.1. Check interior lamp and step lamp operation BL-882. Check door switch BL-79
3. Replace BCMBCS-17
Panic alarm (horn and headlamp) does not activate
when panic alarm button is continuously pressed.1. Check panic alarm mode *
*: Panic alarm can be activated or deactivated. First check the
Panic alarm setting.BL-73
2. Check key fob battery and function BL-77
3. Check headlamp alarm BL-88
4. Check horn chirp function with horn switch.BL-88
5. Check IPDM E/R operation BL-85
6. Check key switch BL-84
7. Replace key fob. Refer to ID Code Entry Procedure.
NOTE:
If the result of key fob function check with CONSULT-III is OK, key
fob is not malfunctioning.BL-89
8. Replace BCMBCS-17
Auto door lock operation does not activate properly.
(All other remote keyless entry system function is
OK.)1. Check auto door lock operation mode *
*: Auto door lock operation can be activated or deactivated. First
check the auto door lock operation setting.BL-73
2. Replace BCMBCS-17
Keyless power window down (open) operation does
not activate properly.
(All other remote keyless entry system function is
OK.)1. Check power window down operation mode *
*: Power window down operation can be activated or deactivated.
First check the power window down setting.BL-73
2. Check power window functionGW-19
3. Replace BCMBCS-17
Symptom Diagnoses/service procedureReference
page

REMOTE KEYLESS ENTRY SYSTEM
BL-77
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Check Key Fob Battery and Function NIS0001K
1. CHECK KEY FOB BATTERY
1. Remove key fob battery. Refer to BL-91, "
Key Fob Battery Replacement" .
2. Measure voltage between battery positive and negative terminals.
NOTE:
Key fob does not function if battery is not set correctly.
OK or NG
OK >> GO TO 2
NG >> Replace battery.
2. CHECK KEY FOB FUNCTION
With CONSULT-III
Check key fob function in “DATA MONITOR” mode with CONSULT-III.
When pushing each button of key fob, the corresponding monitor item should be turned as follows.
OK or NG
OK >> Key fob is OK.
NG >> Replace key fob.Voltage : 2.5 - 3.0V
SEL237W
Condition Monitor item
Pushing LOCK KEYLESS LOCK : ON
Pushing UNLOCK KEYLESS UNLOCK : ON
Keep pushing UNLOCKRKE KEEP UNLK : ON*
*: “RKE KEEP UNLK” turns to ON 3 seconds after UNLOCK
button keeps pushing.
Pushing TRUNK KEYLESS TRUNK : ON
Pushing PANIC KEYLESS PANIC : ON
Pushing LOCK and UNLOCK at the same time RKE LCK - UNLCK : ON

REMOTE KEYLESS ENTRY SYSTEM
BL-89
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
ID Code Entry ProcedureNIS0001U
KEY FOB ID SETUP WITH CONSULT-III
NOTE:
If a key fob is lost, the ID code of the lost key fob must be erased to prevent unauthorized use. When
the ID code of a lost key fob is not known, all controller ID codes should be erased. After all ID codes
are erased, the ID codes of all remaining and/or new key fobs must be re-registered.
1. Touch “WORK SUPPORT”.
2. The items shown on the figure can be set up.

“REMO CONT ID REGIST”
Use this mode to register a key fob ID code.
NOTE:
Register the ID code when key fob or BCM is replaced, or when additional key fob is required.

“REMO CONT ID ERASUR”
Use this mode to erase a key fob ID code.

“REMO CONT ID CONFIR”
Use this mode to confirm if a key fob ID code is registered or not.

BL-90
REMOTE KEYLESS ENTRY SYSTEM
Revision: 2006 November2007 350Z
KEY FOB ID SETUP WITHOUT CONSULT-III
PIIA2839E

REMOTE KEYLESS ENTRY SYSTEM
BL-91
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
NOTE:

If a key fob is lost, the ID code of the lost key fob must be erased to prevent unauthorized use. A specific
ID code can be erased with CONSULT-III. However, when the ID code of a lost key fob is not known, all
controller ID codes should be erased. After all ID codes are erased, the ID codes of all remaining and/or
new key fobs must be re-registered.
To erase all ID codes in memory, register one ID code (key fob) five times. After all ID codes are erased,
the ID codes of all remaining and/or new key fobs must be re-registered.

When registering an additional key fob, the existing ID codes in memory may or may not be erased. If five
ID codes are stored in memory, when an additional code is registered, only the oldest code is erased. If
less than five ID codes are stored in memory, when an additional ID code is registered, the new ID code is
added and no ID codes are erased.

If you need to activate more than two additional new key fobs, repeat the procedure “Additional ID code
entry” for each new key fob.

Entry of maximum five ID codes is allowed. When more than five ID codes are entered, the oldest ID code
will be erased.

Even if same ID code that is already in the memory is input, the same ID code can be entered. The code
is counted as an additional code.
Key Fob Battery ReplacementNIS0001V
SEL411Y

TRUNK LID OPENER
BL-115
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z

through driver side door lock actuator (unlock sensor) terminals 2 and 4,

through grounds M30 and M66.
And power is supplied

to BCM terminal 68

through trunk lid lock assembly (trunk lid opener actuator) terminals 2 and 1

through grounds B5, B6 and T14.
Then trunk lid lock assembly (trunk lid opener actuator) opens trunk.
TRUNK LID OPENER CANCEL OPERATION
When trunk lid opener cancel switch is OFF (CANCEL), it cannot open trunk with trunk lid opener switch.
TRUNK OPENER OPERATION WITH KEY FOB
Open the trunk with key fob. Refer to BL-63, "Trunk Opener Operation/For Roadster" .

BL-126
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: 2006 November2007 350Z
System DescriptionNIS0002T
DESCRIPTION
Operation Flow
Setting the vehicle security system
Initial condition

Ignition switch is in OFF position.
Disarmed phase

When hood, doors, back door (for Coupe) or trunk (for Roadster) is open, the vehicle security system is
set in the disarmed phase on the assumption that the owner is inside or near the vehicle.

When the vehicle security system is in the disarmed phase, the security indicator lamp blinks every 2.4
seconds.
Pre-armed phase and armed phase
When the following operation 1 or 2 is performed, the vehicle security system turns into the “pre-armed”
phase. (The security indicator lamp illuminates.)
1. BCM receives LOCK signal from door key cylinder switch or key fob after all doors and back door (for
Coupe) or trunk (for Roadster) are closed.
2. All doors and back door (for Coupe) or trunk (for Roadster) are closed after doors are locked by key or
door lock and unlock switch.
The security indicator lamp illuminates for 30 seconds. Then, the system automatically shifts into the
“armed” phase.
Canceling the set vehicle security system
When one of the following operations is performed, the armed phase is canceled.
1. Unlock the doors with the key or the key fob.
2. Open the back door (for Coupe) or trunk (for Roadster) with the key fob.
3. Turn ignition switch to “ON” or “ACC” position.
Canceling the alarm operation of the vehicle security system
When one of the following operations is performed, the alarm operation is canceled.

Unlock the door with the key or key fob.

Open the trunk (for Roadster) with the key fob.
Activating the alarm operation of the vehicle security system
Make sure the system is in the armed phase. (The security indicator lamp blinks every 2.4 seconds.)
When the following operation 1 or 2 is performed, the system sounds the horns and flashes the headlamps for
about 50 seconds.
1. Any door or trunk (for Roadster) is opened during armed phase.
PIIA1367E

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-127
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
2. Disconnecting and connecting the battery connector before canceling armed phase.
POWER SUPPLY AND GROUND
Power is supplied at all times

through 10A fuse [No.19, located in the fuse block (J/B)]

to security indicator lamp terminal 1.
Power is supplied at all times

through 40A fusible link (letter F , located in the fuse and fusible link box)

to BCM terminal 55

through 10A fuse [No.18, located in the fuse block (J/B)]

to BCM terminal 42.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to BCM terminal 11.
Ground is supplied.

to BCM terminal 52

through body grounds M30 and M66.
INITIAL CONDITION TO ACTIVATE THE SYSTEM
The operation of the vehicle security system is controlled by the doors and trunk (for Roadster).
To activate the vehicle security system, BCM must receive signals indicating the doors and trunk (for Road-
ster) are closed and the doors are locked by key or key fob.
When a door is open, BCM terminals 12, 65 receives a ground signal from each door switch.
When driver side door is unlocked by power window main switch (door lock and unlock switch), BCM terminal
22 receives a signal from terminal 12 of power window main switch.
When passenger side door is unlocked by power window sub-switch (door lock and unlock switch), BCM ter-
minal 22 receives a signal from terminal 16 of power window sub-switch.
The IPDM E/R then sends a signal to the BCM via CAN communication line.
When the back door (for Coupe) or trunk (for Roadster) is open, BCM terminal 57 (for Roadster) or 58 (for
Coupe) receives a ground signal

from terminal 1 of the back door switch (for Coupe) or terminal 3 of trunk lid lock assembly (trunk room
lamp switch) (for Roadster)

through body grounds B5, B6,T14, D105 (for Coupe) or B5, B6, T14 (for Roadster).
VEHICLE SECURITY SYSTEM ALARM OPERATION
The vehicle security system is triggered by

opening a driver or passenger side door

opening the back door (for Coupe)

opening the trunk (for Roadster)

detection of battery disconnect and connect.
The vehicle security system will be triggered once the system is in armed phase,
When BCM receives a ground signal at terminals 12, 62 (door switch), 57 (trunk room lamp switch) or 58 (back
door switch).
Power is supplied at all times

to horn relay terminal 2

through 15A fuse (No. 35, located in the fuse and fusible link box).
When the vehicle security system is triggered, ground is supplied intermittently to both headlamp relay and
horn relay.
When both headlamp relay (with built-in IPDM E/R) and horn relay are energized and then power is supplied
to headlamps (high beam and low beam) and horns (HIGH and LOW).
The headlamps flash and the horn sounds intermittently.
The alarm automatically turns off after 50 seconds, but will reactivate if the vehicle is tampered with again.
VEHICLE SECURITY SYSTEM DEACTIVATION
To deactivate the vehicle security system, a door must be unlocked or back door (for Coupe) or trunk (for
Roadster) must be opened with the key or key fob.

BL-128
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: 2006 November2007 350Z
When the key is used to unlock a door, BCM terminal 22 receives signal

from terminal 12 of the power window main switch (door lock and unlock switch).
When the BCM receives either above signal or unlock signal from key fob, the vehicle security system is deac-
tivated. (Disarmed phase)
PANIC ALARM OPERATION
Remote keyless entry system may or may not operate vehicle security system (horn and headlamps) as
required.
When the panic alarm button on the keyfob is triggered, ground is supplied intermittently to both headlamp
relay and horn relay.
When both headlamp relay (with built-in IPDM E/R) and horn relay are energized and then power is supplied
to headlamps (high beam and low beam) and horns (HIGH and LOW).
The headlamp flashes and the horn sounds intermittently.
The alarm automatically turns off after 25 seconds or when BCM receives any signal from key fob.
CAN Communication System DescriptionNIS0002U
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitNIS0002V
Refer to LAN-4, "CAN Communication System" .

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-135
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2006 November2007 350Z
Terminals and Reference Value for BCMNIS0002Y
Termi-
nal Wire
colorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
11 LG Ignition switch (ACC) Input Ignition switch (ACC or ON) Battery voltage
12 P Passenger side door switch Input ON (Open) → OFF (Closed) 0 → 5
18 BRemote keyless entry receiver
(Ground)—— 0
19 YRemote keyless entry receiver
(Power supply)OutputKey is inserted is IGN key cyl-
inder0
All door closed
20 LRemote keyless entry receiver
(Signal)InputKey is inserted is IGN key cyl-
inder0
Stand-by
When remote keyless entry
receiver receives signal from
keyfob
22 YPower window switch
(Serial link)Input/
OutputDriver side door and passen-
ger side door are closed.
(Each door switch is OFF)
23 G/OR Security indicator lamp OutputGoes off → Illuminates (Every
2.4 seconds)Battery voltage → 0
39 L CAN-HInput/
Output——
40 P CAN-LInput/
Output——
42 GY Ignition switch (ON) Input Ignition switch (ON or START) Battery voltage
52 B Ground — — 0
55 R Power source (Fusible link) Input — Battery voltage
57 RTrunk room lamp switch
(For Roadster)Input
ON (Open) → OFF (Closed)
0 → Battery voltage*
1
58 R/W Back door switch (For Coupe) Input
62 L Driver side door switch Input ON (Open) → OFF (Closed) 0 → 5
OCC3881D
OCC3879D
OCC3880D
PIIA2344J