clutch NISSAN 350Z 2007 Z33 Engine Control Workshop Manual

EC-30
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
Revision: 2006 November2007 350Z
AUTOMATIC SPEED CONTROL DEVICE (ASCD)PFP:18930
System DescriptionNBS0002M
INPUT/OUTPUT SIGNAL CHART
*: This signal is sent to the ECM through CAN communication line.
BASIC ASCD SYSTEM
Refer to Owner's Manual for ASCD operating instructions.
Automatic Speed Control Device (ASCD) allows a driver to keep vehicle at predetermined constant speed
without depressing accelerator pedal. Driver can set vehicle speed in advance between approximately 40 km/
h (25 MPH) and 144 km/h (89 MPH).
ECM controls throttle angle of electric throttle control actuator to regulate engine speed.
Operation status of ASCD is indicated by CRUISE indicator and SET indicator in combination meter. If any
malfunction occurs in ASCD system, it automatically deactivates control.
NOTE:
Always drive vehicle in safe manner according to traffic conditions and obey all traffic laws.
SET OPERATION
Press MAIN switch. (The CRUISE indicator in combination meter illuminates.)
When vehicle speed reaches a desired speed between approximately 40 km/h (25 MPH) and 144 km/h (89
MPH), press SET/COAST switch. (Then SET indicator in combination meter illuminates.)
ACCELERATE OPERATION
If the RESUME/ACCELERATE switch is pressed during cruise control driving, increase the vehicle speed until
the switch is released or vehicle speed reaches maximum speed controlled by the system.
And then ASCD will keep the new set speed.
CANCEL OPERATION
When any of following conditions exist, cruise operation will be canceled.

CANCEL switch is pressed

More than 2 switches at ASCD steering switch are pressed at the same time (Set speed will be cleared)

Brake pedal is depressed

Clutch pedal is depressed or gear position is changed to the neutral position (M/T models)

Selector lever is changed to N, P, R position (A/T models)

Vehicle speed decreased to 13 km/h (8 MPH) lower than the set speed

VDC/TCS system is operated
When the ECM detects any of the following conditions, the ECM will cancel the cruise operation and inform
the driver by blinking indicator lamp.

Engine coolant temperature is slightly higher than the normal operating temperature, CRUISE lamp may
blink slowly.
When the engine coolant temperature decreases to the normal operating temperature, CRUISE lamp will
stop blinking and the cruise operation will be able to work by pressing SET/COAST switch or RESUME/
ACCELERATE switch.

Malfunction for some self-diagnoses regarding ASCD control: SET lamp will blink quickly.
If MAIN switch is turned to OFF during ASCD is activated, all of ASCD operations will be canceled and vehicle
speed memory will be erased.
Sensor Input signal to ECM ECM function Actuator
ASCD brake switch Brake pedal operation
ASCD vehicle speed controlElectric throttle control
actuator Stop lamp switch Brake pedal operation
ASCD clutch switch (M/T models) Clutch pedal operation
ASCD steering switch ASCD steering switch operation
Park/neutral position (PNP) switch Gear position
Wheel sensor. Vehicle speed*
TCM (A/T models) Powertrain revolution*

AUTOMATIC SPEED CONTROL DEVICE (ASCD)
EC-31
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
COAST OPERATION
When the SET/COAST switch is pressed during cruise control driving, decrease vehicle set speed until the
switch is released. And then ASCD will keep the new set speed.
RESUME OPERATION
When the RESUME/ACCELERATE switch is pressed after cancel operation other than pressing MAIN switch
is performed, vehicle speed will return to last set speed. To resume vehicle set speed, vehicle condition must
meet following conditions.

Brake pedal is released

Clutch pedal is released (M/T models)

A/T selector lever is in other than P and N positions (A/T models)

Vehicle speed is greater than 40 km/h (25 MPH) and less than 144 km/h (89 MPH)
Component DescriptionNBS0002N
ASCD STEERING SWITCH
Refer to EC-602
ASCD BRAKE SWITCH
Refer to EC-610 and EC-671 .
ASCD CLUTCH SWITCH
Refer to EC-610 and EC-671 .
STOP LAMP SWITCH
Refer to EC-610 , EC-628 and EC-671 .
ELECTRIC THROTTLE CONTROL ACTUATOR
Refer to EC-561 , EC-571 , EC-580 and EC-592 .
ASCD INDICATOR
Refer to EC-681 .

TROUBLE DIAGNOSIS
EC-99
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
1. Heated oxygen sensor 2 (bank 2) 2. Heated oxygen sensor 2 (bank 2)
harness connector3. Heated oxygen sensor 2 (bank 1)
4. Heated oxygen sensor 2 (bank 1)
harness connector
:Vehicle front
1. Accelerator pedal 2. Accelerator pedal position sensor 3. ECM
4. ECM harness connector
1. Stop lamp switch 2. ASCD brake switch 3. Brake pedal
4. ASCD clutch switch 5. Clutch pedal
1. ASCD steering switch 2. RESUME/ACCELERATE switch 3. SET/COAST switch
4. CANCEL switch 5. MAIN switch
PBIB3502E
PBIB3496E
PBIB3498E
PBIB3497E

EC-114
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)110 Y Engine speed output signal[Engine is running]

Warm-up condition

Idle speed
NOTE:
The pulse cycle changes depending on rpm
at idle1V
[Engine is running]

Engine speed: 2,000 rpm1V
111 O RSensor power supply
(Refrigerant pressure sen-
sor)[Ignition switch: ON]5V
11 2 P USensor ground
(EVAP control system pres-
sure sensor)[Engine is running]

Warm-up condition

Idle speed0V
113 P CAN communication line — —
114 L CAN communication line — —
11 6 WSensor ground
(Refrigerant pressure sen-
sor)[Engine is running]

Warm-up condition

Idle speed0V
117 PU Data link connector[Ignition switch: ON]

GST: Disconnected5V - Battery voltage (11 - 14V)
121 LGEVAP canister vent control
valve[Ignition switch: ON]BATTERY VOLTAGE
(11 - 14V)
122 P/L Stop lamp switch[Ignition switch: OFF]

Brake pedal: Fully released0V
[Ignition switch: OFF]

Brake pedal: Slightly depressedBATTERY VOLTAGE
(11 - 14V)
123
124B/W
B/RECM ground[Engine is running]

Idle speedBody ground
125 R Power supply for ECM[Ignition switch: ON]BATTERY VOLTAGE
(11 - 14V)
126 L/OR ASCD brake switch[Ignition switch: ON]

Brake pedal: Slightly depressed (A/T)

Brake pedal and/or clutch pedal: Slightly
depressed (M/T)0V
[Ignition switch: ON]

Brake pedal: Fully released (A/T)

Brake pedal and clutch pedal: Fully released
(M/T)BATTERY VOLTAGE
(11 - 14V)
127
128B
BECM ground[Engine is running]

Idle speedBody ground TER-
MINAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)
PBIB3557E
PBIB3558E

TROUBLE DIAGNOSIS
EC-117
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
ENGINE CONTROL COMPONENT PARTS/CONTROL SYSTEMS APPLICATION
ItemDIAGNOSTIC TEST MODE
WORK
SUPPORTSELF-DIAGNOSTIC
RESULTS
DATA
MONI-
TORACTIVE
TESTDTC & SRT
CONFIRMATION
DTC*1FREEZE
FRAME
DATA*
2
SRT STA-
TUSDTC
WORK
SUP-
PORT
ENGINE CONTROL COMPONENT PARTS
INPUT
Crankshaft position sensor (POS)×××
Camshaft position sensor (PHASE)×××
Mass air flow sensor××
Engine coolant temperature sensor××××
Engine oil temperature sensor×
Air Fuel ratio (A/F) sensor 1××××
Heated oxygen sensor 2××××
Vehicle speed sensor×××
Accelerator pedal position sensor××
Throttle position sensor×××
Fuel tank temperature sensor×××
EVAP control system pressure sensor××
Intake air temperature sensor×××
Knock sensor×
Refrigerant pressure sensor×
Closed throttle position switch (accel-
erator pedal position sensor signal)×
Air conditioner switch×
Park/neutral position (PNP) switch××
Stop lamp switch××
Power steering pressure sensor××
Battery voltage×
Load signal×
Exhaust valve timing control position
sensor××
Fuel level sensor××
ASCD steering switch××
ASCD brake switch××
ASCD clutch switch××

TROUBLE DIAGNOSIS
EC-123
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
NOTE:
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.VHCL SPEED SE [km/
h] or [mph]

The vehicle speed computed from the vehicle speed
signal sent from TCM is displayed.
SET VHCL SPD
[km/h] or [mph]

The preset vehicle speed is displayed.
MAIN SW
[ON/OFF]

Indicates [ON/OFF] condition from MAIN switch sig-
nal.
CANCEL SW
[ON/OFF]

Indicates [ON/OFF] condition from CANCEL switch
signal.
RESUME/ACC SW
[ON/OFF]

Indicates [ON/OFF] condition from RESUME/ACCEL-
ERATE switch signal.
SET SW
[ON/OFF]

Indicates [ON/OFF] condition from SET/COAST
switch signal.
BRAKE SW1
[ON/OFF]

Indicates [ON/OFF] condition from ASCD brake switch
signal and ASCD clutch switch signal (M/T)
BRAKE SW2
[ON/OFF]

Indicates [ON/OFF] condition of stop lamp switch sig-
nal.
VHCL SPD CUT
[NON/CUT]

Indicates the vehicle cruise condition.
NON: Vehicle speed is maintained at the ASCD set
speed.
CUT: Vehicle speed decreased to excessively low
compared with the ASCD set speed, and ASCD oper-
ation is cut off.
LO SPEED CUT
[NON/CUT]

Indicates the vehicle cruise condition.
NON: Vehicle speed is maintained at the ASCD set
speed.
CUT: Vehicle speed decreased to excessively low, and
ASCD operation is cut off.
AT OD MONITOR
[ON/OFF]

Indicates [ON/OFF] condition of A/T O/D according to
the input signal from the TCM.
For M/T models always “OFF” is displayed.
AT OD CANCEL
[ON/OFF]

Indicates [ON/OFF] condition of A/T O/D cancel
request signal.
For M/T models always “OFF” is displayed.
CRUISE LAMP
[ON/OFF]

Indicates [ON/OFF] condition of CRUISE lamp deter-
mined by the ECM according to the input signals.
SET LAMP
[ON/OFF]

Indicates [ON/OFF] condition of SET lamp determined
by the ECM according to the input signals.
EXH V/T LEARN [YET/
CMPLT]

Display the condition of Exhaust Valve Timing Control
Learning
YET: Exhaust Valve Timing Control Learning has not
been performed yet.
CMPLT: Exhaust Valve Timing Control Learning has
already been performed successfully.
A/F ADJ-B1

Indicates the correction of factor stored in ECM. The
factor is calculated from the difference between the
target air-fuel ratio stored in ECM and the air-fuel ratio
calculated from A/F sensor 1 signal. A/F ADJ-B2
Voltage [V]

Voltage, frequency, duty cycle or pulse width mea-
sured by the probe.

Only “#” is displayed if item is unable to be
measured.

Figures with “#”s are temporary ones. They
are the same figures as an actual piece of data
which was just previously measured. Frequency [msec], [Hz]
or [%]
DUTY-HI
DUTY-LOW
PLS WIDTH-HI
PLS WIDTH-LOWMonitored item [Unit] Description Remarks

EC-130
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
IDL A/V LEARN
Engine: RunningIdle air volume learning has not been
performed yet.YET
Idle air volume learning has already
been performed successfully.CMPLT
ENG OIL TEMP

Engine: After warming up More than 70°C (158°F)
TRVL AFTER MIL

Ignition switch: ONVehicle has traveled after MIL has
turned ON.0 - 65,535 km
(0 - 40,723 mile)
A/F S1 HTR(B1)
A/F S1 HTR(B2)

Engine: After warming up, idle the engine
(More than 140 seconds after starting engine)4 - 100%
AC PRESS SEN

Engine: Idle

Both A/C switch and blower switch are ON.
(Compressor operates.)1.0 - 4.0V
VHCL SPEED SE

Turn drive wheels and compare CONSULT-III value with the speedometer
indication.Almost the same speed as the
speedometer indication
SET VHCL SPD

Engine: Running ASCD: OperatingThe preset vehicle speed is
displayed.
MAIN SW

Ignition switch: ONMAIN switch: Pressed ON
MAIN switch: Released OFF
CANCEL SW

Ignition switch: ONCANCEL switch: Pressed ON
CANCEL switch: Released OFF
RESUME/ACC SW

Ignition switch: ONRESUME/ACCELERATE switch:
PressedON
RESUME/ACCELERATE switch:
ReleasedOFF
SET SW

Ignition switch: ONSET/COAST switch: Pressed ON
SET/COAST switch: Released OFF
BRAKE SW1
(ASCD brake switch)

Ignition switch: ON

Brake pedal: Fully released (A/T)

Brake pedal and clutch pedal: Fully
released (M/T)ON

Brake pedal: Slightly depressed (A/T)

Brake pedal and/or clutch pedal:
Slightly depressed (M/T)OFF
BRAKE SW2
(Stop lamp switch)

Ignition switch: ONBrake pedal: Fully released OFF
Brake pedal: Slightly depressed ON
VHCL SPD CUT

Ignition switch: ON NON
LO SPEED CUT

Ignition switch: ON NON
AT OD MONITOR

Ignition switch: ON OFF
AT OD CANSEL

Ignition switch: ON OFF
CRUISE LAMP

Ignition switch: ONMAIN switch: Pressed at the 1st time →
at the 2nd timeON → OFF
SET LAMP

MAIN switch: ON

When vehicle speed is between
40 km/h (25 MPH) and 144 km/h
(89MPH)ASCD: Operating ON
ASCD: Not operating OFF
EXH V/T LEARN

Engine: RunningExhaust Valve Timing Control Learning
has not been performed yet.YET
Exhaust Valve Timing Control Learning
has not been performed yet.CMPLT
A/F ADJ B1

Engine: Running –0.330 - 0.330
A/F ADJ B2

Engine: Running –0.330 - 0.330 MONITOR ITEM CONDITION SPECIFICATION

EC-610
DTC P1572 ASCD BRAKE SWITCH
Revision: 2006 November2007 350Z
DTC P1572 ASCD BRAKE SWITCHPFP:25320
Component DescriptionNBS000G0
When the brake pedal is depressed, ASCD brake switch is turned
OFF and stop lamp switch is turned ON. ECM detects the state of
the brake pedal by this input of two kinds (ON/OFF signal).
Refer to EC-30, "
AUTOMATIC SPEED CONTROL DEVICE (ASCD)"
for the ASCD function.
CONSULT-III Reference Value in Data Monitor ModeNBS000G1
Specification data are reference values.
On Board Diagnosis LogicNBS000G2

This self-diagnosis has the one trip detection logic.

The MIL will not light up for this self-diagnosis.
NOTE:

If DTC P1572 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605.
Refer to EC-512, "
DTC P0605 ECM".

This self-diagnosis has the one trip detection logic. When malfunction A is detected, DTC is not
stored in ECM memory. And in that case, 1st trip DTC and 1st trip freeze frame data are displayed.
1st trip DTC is erased when ignition switch OFF. And even when malfunction A is detected in two
consecutive trips, DTC is not stored in ECM memory.
PBIB1282E
MONITOR ITEM CONDITION SPECIFICATION
BRAKE SW1
(ASCD brake switch)

Ignition switch: ON

Brake pedal: Fully released (A/T)

Brake pedal and clutch pedal: Fully
released (M/T)ON

Brake pedal: Slightly depressed (A/T)

Brake pedal and/or clutch pedal:
Slightly depressed (M/T)OFF
BRAKE SW2
(Stop lamp switch)

Ignition switch: ONBrake pedal: Fully released OFF
Brake pedal: Slightly depressed ON
DTC No.Trouble Diagnosis
NameDTC Detecting Condition Possible Cause
P1572
1572ASCD brake switchA)When the vehicle speed is above 30km/h
(19 MPH), ON signals from the stop lamp
switch and the ASCD brake switch are sent
to ECM at the same time.

Harness or connectors
(The stop lamp switch circuit is shorted.)

Harness or connectors
(The ASCD brake switch circuit is shorted.)

Harness or connectors
(The ASCD clutch switch circuit is shorted.)
(M/T models)

Stop lamp switch

ASCD brake switch

ASCD clutch switch (M/T models)

Incorrect stop lamp switch installation

Incorrect ASCD brake switch installation

Incorrect ASCD clutch switch installation
(M/T models)

ECM B)ASCD brake switch signal is not sent to
ECM for extremely long time while the vehi-
cle is driving

DTC P1572 ASCD BRAKE SWITCH
EC-615
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
Diagnostic ProcedureNBS000G5
A/T MODELS
1. CHECK OVERALL FUNCTION-I
With CONSULT-III
1. Turn ignition switch ON.
2. Select “BRAKE SW1” in “DATA MONITOR” mode with CONSULT-III.
3. Check “BRAKE SW1” indication under the following conditions.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check voltage between ECM terminal 126 and ground under the
following conditions.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
TER-
MINAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)
122 P/L Stop lamp switch[Ignition switch: OFF]

Brake pedal: Fully released0V
[Ignition switch: OFF]

Brake pedal: Slightly depressedBATTERY VOLTAGE
(11 - 14V)
126 L/OR ASCD brake switch[Ignition switch: ON]

Brake pedal and/or clutch pedal: Slightly
depressed0V
[Ignition switch: ON]

Brake pedal and clutch pedal: Fully releasedBATTERY VOLTAGE
(11 - 14V)
CONDITION INDICATION
Brake pedal: Slightly depressed OFF
Brake pedal: Fully released ON
CONDITION VOLTAGE
Brake pedal: Slightly depressed Approximately 0V
Brake pedal: Fully released Battery voltage
PBIB3577E

DTC P1572 ASCD BRAKE SWITCH
EC-619
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 November2007 350Z
12. CHECK STOP LAMP SWITCH
Refer to EC-624, "
Component Inspection"
OK or NG
OK >> GO TO 13.
NG >> Replace stop lamp switch.
13. CHECK INTERMITTENT INCIDENT
Refer to EC-141, "
TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT" .
>>INSPECTION END
M/T MODELS
1. CHECK OVERALL FUNCTION-I
With CONSULT-III
1. Turn ignition switch ON.
2. Select “BRAKE SW1” in “DATA MONITOR” mode with CONSULT-III.
3. Check “BRAKE SW1” indication under the following conditions.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check voltage between ECM terminal 126 and ground under the
following conditions.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
CONDITION INDICATION
Brake pedal and/or clutch pedal: Slightly depressed OFF
Brake pedal and clutch pedal: Fully released ON
CONDITION VOLTAGE
Brake pedal and/or clutch pedal: Slightly depressed Approximately 0V
Brake pedal and clutch pedal: Fully released Battery voltage
PBIB3577E