belt NISSAN 350Z 2007 Z33 Lighting System Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2007, Model line: 350Z, Model: NISSAN 350Z 2007 Z33Pages: 172, PDF Size: 5.8 MB
Page 1 of 172
LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION LT
A
B
LT
Revision: 2006 November2007 350Z
LIGHTING SYSTEM
PRECAUTIONS .......................................................... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 4
Precautions for Battery Service ................................ 4
General Precautions for Service Operations ............ 4
HEADLAMP (FOR USA) ............................................ 5
Component Parts and Harness Connector Location ..... 5
System Description .................................................. 5
OUTLINE ............................................................... 5
HEADLAMP OPERATION .................................... 6
COMBINATION SWITCH READING FUNCTION ..... 7
EXTERIOR LAMP BATTERY SAVER CONTROL ..... 7
REMOTE KEYLESS ENTRY SYSTEM OPERA-
TION ...................................................................... 7
VEHICLE SECURITY SYSTEM ............................ 7
XENON HEADLAMP ............................................. 7
CAN Communication System Description ................ 7
CAN Communication Unit ........................................ 7
Schematic ................................................................ 8
Wiring Diagram — H/LAMP — ................................. 9
Terminals and Reference Values for BCM ............. 13
Terminals and Reference Values for IPDM E/R ..... 15
How to Proceed With Trouble Diagnosis ................ 15
Preliminary Check .................................................. 15
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 15
CONSULT-III Function (BCM) ................................ 17
WORK SUPPORT ............................................... 17
DATA MONITOR ................................................. 17
ACTIVE TEST ..................................................... 18
CONSULT-III Function (IPDM E/R) ........................ 18
DATA MONITOR ................................................. 18
ACTIVE TEST ..................................................... 18
Headlamp Does Not Change To High Beam (Both
Sides) ..................................................................... 19
Headlamp Does Not Change To High Beam (One
Side) ....................................................................... 21
High Beam Indicator Lamp Does Not Illuminate .... 22
Headlamp Low Beam Does Not Illuminate (Both Sides) ..................................................................... 22
Headlamp Low Beam Does Not Illuminate (One
Side) ....................................................................... 24
Headlamps Does Not Turn OFF ............................. 26
General Information for Xenon Headlamp Trouble
Diagnosis ................................................................ 26
Caution: .................................................................. 26
Xenon Headlamp Trouble Diagnosis ...................... 27
Aiming Adjustment .................................................. 27
PREPARATION BEFORE ADJUSTING .............. 27
LOW BEAM AND HIGH BEAM ........................... 28
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 28
Bulb Replacement .................................................. 28
HEADLAMP HIGH/LOW BEAM .......................... 28
PARKING LAMP .................................................. 29
FRONT TURN SIGNAL LAMP ............................ 29
FRONT SIDE MARKER LAMP ........................... 29
Removal and Installation ........................................ 29
REMOVAL ........................................................... 29
INSTALLATION ................................................... 29
Disassembly and Assembly .................................... 30
DISASSEMBLY ................................................... 30
ASSEMBLY ......................................................... 31
Servicing to Replace Headlamps When Damaged ... 31
INSTALLATION OF HEADLAMP BRACKET ....... 31
HEADLAMP (FOR CANADA) - DAYTIME LIGHT
SYSTEM - .................................................................. 32
Component Parts and Harness Connector Location ... 32
System Description ................................................. 32
OUTLINE ............................................................. 32
HEADLAMP OPERATION ................................... 33
DAYTIME LIGHT OPERATION ........................... 34
OPERATION ........................................................ 35
COMBINATION SWITCH READING FUNCTION ... 35
EXTERIOR LAMP BATTERY SAVER CONTROL ... 35
INTERLOCKED OPERATION WITH REMOTE
KEYLESS ENTRY SYSTEM ............................... 35
INTERLOCKED OPERATION WITH VEHICLE
SECURITY SYSTEM .......................................... 35
Page 4 of 172
LT-4
PRECAUTIONS
Revision: 2006 November2007 350Z
PRECAUTIONS PFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NKS00541
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Battery ServiceNKS00542
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
General Precautions for Service OperationsNKS00543
Never work with wet hands.
Xenon headlamp includes high voltage generating part. Be sure
to disconnect battery negative cable (negative terminal) or
power fuse before removing, installing, or touching the xenon
headlamp (including lamp bulb).
Turn the lighting switch OFF before disconnecting and connect-
ing the connector.
When turning the xenon headlamp on and while it is illuminated,
never touch the harness, bulb, and socket of the headlamp.
When checking the headlamp on/off operation, check it on vehi-
cle and with the power connected to the vehicle-side connector.
Do not touch the headlamp bulb glass surface with bare hands or allow oil or grease to get on it. Do not
touch the headlamp bulb just after the headlamp is turned off, because it is very hot.
Install the xenon headlamp bulb socket correctly. If it is installed
improperly, high-voltage leak or corona discharge may occur
that can melt the bulb, connector, and housing. Do not illuminate
the xenon headlamp bulb out of the headlamp housing. Doing
so can cause fire and harm your eyes.
When the bulb has burned out, wrap it in a thick vinyl bag and
discard. Do not break the bulb.
Leaving the bulb removed from the headlamp housing for a long
period of time can deteriorate the performance of the lens and
reflector (dirt, clouding). Always prepare a new bulb and have it
on hand when replacing the bulb.
When adjusting the headlamp aiming, turn the aiming adjust-
ment screw only in the tightening direction. (If it is necessary to loosen the screw, first fully loosen the
screw, and then turn it in the tightening direction.)
Do not use organic solvent (paint thinner or gasoline) to clean lamps and to remove old sealant.
PKIB7344E
EL-3422D