wiper fluid NISSAN 350Z 2007 Z33 Wiper, Washer And Horn Workshop Manual

WW-30
FRONT WIPER AND WASHER SYSTEM
Revision: 2006 November2007 350Z
Removal and Installation of Front Wiper Arms, Adjustment of Wiper Arms Stop
Location
NKS0052L
REMOVAL
1. Turn front wiper switch ON to operate wiper motor, and then turn front wiper switch OFF (auto stop).
2. Remove washer tube from washer tube joint.
3. Open hood, remove front wiper arm caps, and remove front wiper arm nuts.
4. Raise front wiper arms, and remove front wiper arms from vehicle.
INSTALLATION
1. Clean up the pivot area as shown in the figure. This will reduce
possibility of front wiper arm looseness.
2. Prior to front wiper arms installation, turn front wiper switch ON
to operate wiper motor, and then turn front wiper switch OFF
(auto stop).
3. Lift the blade up and then set it down onto windshield glass sur-
face to set the blade center to clearance “L1” & “L2” immedi-
ately.
4. Tighten front wiper arm nuts to specified torque.
5. Install washer tube from washer tube joint.
6. Spray washer fluid. Turn front wiper switch ON to operate wiper
motor, and then turn front wiper switch OFF (auto stop).
7. Make sure that wiper blades stop within clearance “L1” & “L2”.
8. Install front wiper arm caps.
Removal and Installation of Front Wiper Drive AssemblyNKS0052M
REMOVAL
1. Remove front wiper arms. Refer to WW-30, "REMOVAL" .
2. Remove cowl top cover. Refer to EI-20, "
COWL TOP" .
3. Disconnect wiper motor connector (1) and remove connector
clip (A).
4. Remove front wiper drive assembly mounting bolts (B), and
remove front wiper drive assembly (2) from the vehicle.
INSTALLATION
1. Install front wiper drive assembly to the vehicle.
2. Connect wiper motor connector. Turn front wiper switch ON to operate wiper motor, and then turn front
wiper switch OFF (auto stop).
3. Install connector clips to the wiper frame, and install cowl top cover. Refer to EI-20, "
COWL TOP" .
SEL024J
Front wiper arm nuts : 23.6 N·m (2.4 kg-m, 18 ft-lb)
Clearance “L1” : 63.9 ± 7.5 mm (2.516 ± 0.295 in)
Clearance “L2” : 32.0 ± 6.5 mm (1.260 ± 0.256 in)
PKIA9951E
SKIB7455E
Front wiper drive assembly mounting bolts : 4.5 N·m (0.46 kg-m, 40 in-lb)

REAR WIPER AND WASHER SYSTEM
WW-47
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: 2006 November2007 350Z
INSTALLATION
1. Clean up the pivot area as shown in the figure. This will reduce
possibility of rear wiper arm nut looseness.
2. Prior to rear wiper arm installation, turn rear wiper switch ON to
operate wiper motor, and then turn rear wiper switch OFF (auto
stop).
3. Lift the blade up and then set it down onto windshield glass sur-
face to set the blade center to clearance “L” immediately.
4. Tighten wiper arm nuts to specified torque.
5. Spray washer fluid. Turn rear wiper switch ON to operate wiper
motor, and then turn rear wiper switch OFF (auto stop).
6. Make sure that wiper blade stop within clearance “L”.
7. Install rear wiper arm caps.
Removal and Installation of Rear Wiper Motor NKS0053B
SKIA0082J
Rear wiper arm nut : 15.2 N·m (1.6 kg-m, 11 ft-lb)
Clearance “L” : 30 ± 7.5 mm (1.181 ± 0.295 in)
PKIA1914E
PKIB5009E

REAR WIPER AND WASHER SYSTEM
WW-49
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: 2006 November2007 350Z
Washer Tube LayoutNKS0053D
Removal and Installation of Rear Washer NozzleNKS0053E
REMOVAL
1. Remove washer tube(1).
2. While pressing pawl (A) on the reverse side of rear washer noz-
zle (2), remove rear washer nozzle (2) from back door (3).
INSTALLATION
Installation is the reverse order of removal. Adjust nozzle spray location. Refer to WW-48, "Washer Nozzle
Adjustment" .
Inspection for Washer NozzleNKS0053F
CHECK VALVE INSPECTION
A check valve is provided in washer fluid line. Be careful not to con-
nect check valve to washer tube in the wrong direction.
Inspection of Rear Wiper and Washer Switch CircuitNKS0053G
Refer to WW-34, "Removal and Installation of Front Wiper and Washer Switch" .
Removal and Installation of Rear Wiper and Washer SwitchNKS0053H
Refer to WW-34, "Removal and Installation of Front Wiper and Washer Switch" .
PKIA1912E
SKIB7454E
SEL411H