wipers NISSAN ALTIMA 2008 L32A / 4.G Quick Reference Guide

INTELLIGENT K EY SYSTEM
The Intelligent Key system allows you to lock or unlock your vehicle, open your trunk and start the engine.
Note: It is important to make sure the Intelligent Key is with you (that is, in your pocket or purse).
 The operating range of the door and trunk lock/unlock function is approximately 31 in (0.8 m).
 Locking the vehicle - Push any door handle Request Switch 01 once.
 Unlocking the vehicle - Push any door handle Request Switch 01 once. The corresponding door will unlock. Push the door handle Request Switch 01 again within 5 seconds; all other doors will unlock.
o Pe NING tH e tRUNK
 To open the trunk release using the Request Switch, your Intelligent Key must be with you.
 Push the Request/Release Switch 02 located to the far right under the trunk handle.
 Pull up and out on the handle to open the trunk.
S tAR tING tH e eNGIN e
 Depress the brake pedal (CVT) or clutch pedal (MT).
 Push the ignition switch to start the engine.
t URNING tH e eNGIN e oFF
 Shift the selector lever to the P (Park) position (CVT) or to the N (Neutral) position (manual transmission) and apply the parking brake.
 Push the ignition switch to turn the engine off.
IN te LLIG eN t K eY P oRt
 If the battery of the Intelligent Key is almost discharged, the guide light of the Intelligent Key port blinks and the Intelligent Key insertion indicator is displayed in the vehicle information display.
 To start the engine, insert the Intelligent Key into the key port in the direction indicated until it latches into place.
 To remove the Intelligent Key from the port, push the ignition switch to turn the engine off and pull the Intelligent Key out of the port.
 The Intelligent Key port does not charge the Intelligent Key battery. If you see the low battery indicator, replace the battery as soon as possible. Refer to the Owner’s
Manual for detailed information regarding changing the battery.
01
02
2
WINDSHIELD WIPER/WASHER SWITCH
 The ignition switch must be in the ON position to activate the windshield wipers.
 Push the lever down to operate the windshield wipers.
 Switch operation includes:
INT Intermittent – Wipers operate intermittently and can

HEADLIGHT AND TURN SIGNAL CONTROL
to AC tIVA te t H e AU toLIGH t SYS teM
(if so equipped):
Turn the headlight control switch 01 to the AUTO position to activate the autolight system. The autolight system can:
 Turn the headlights on automatically when it is dark.
 Turn the headlights off automatically when it is light.
 Keep the headlights on for 45 seconds after you turn the ignition switch to OFF and all doors are closed.
to DeAC tIVA te t H e AU toLIGH t SYS teM :
 Turn the headlight control switch 01 to the OFF, or position.
H eADLIGH t CoNtR o L SWI tCH
 Turn the headlight control switch 01 to the position to turn on the front parking, tail, license plate and instrument panel lights.
 Turn the headlight control switch 01 to the position to turn on the headlights. All other lights remain on.
F o G LIGH t oPe RA tIo N (if so equipped)
N OTE:
The headlights must be on and the low beams selected for the fog lights to
operate.
 Turn the fog light switch (inside collar) 02 to the position to turn on the fog lights.
 Turn the fog light switch (inside collar) 02 to the OFF position to turn off the fog lights.
t URN SIGNAL SWI tCH
 Move the headlight control switch up or down A to signal a turning direction. When the turn is completed, the turn signals cancel automatically.
 To signal a lane change, move the headlight control switch up or down b to the point where the indicator light begins to flash, but the headlight control switch does not latch.
HIGH B eAM
 Push the headlight control switch forward C to select the high beam function. The blue indicator light illuminates. Pull the headlight switch back to the original position to select the low beam. The blue indicator light goes off.
 Pull and release the headlight control switch D to flash the headlight high beams on and off.
3
be adjusted by turning the time control. Also, the intermittent operation speed varies
in accordance with the vehicle speed. (For example, when the vehicle speed is high,
the intermittent operation speed will be faster.)
LO Low speed – Wipers operate at a continuous low speed.
HI High speed – Wipers operate at a continuous high speed.
MIST Mist – Lift the lever up for one sweep operation of the wiper.

LCN0042
Wash – Pull the lever toward you. Wipers automatically wipe several times.
A b
b A
C
D
0102