ECU NISSAN ARMADA 2007 1.G Quick Reference Guide

AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function.
 Entry/exit function.
MEMORY STORAGE FUNCTION
Two positions for the driver’s seat, accelerator and brake pedals, and outside mirrors can be stored in the automatic driver positioner memory. Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the P (Park) position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
SEAT BELT WARNING LIGHT AND CHIME
 The light and chime remind you to fasten your seat belts. The
light illuminates whenever the ignition key is turned to the ON
or START position and remains illuminated until the driver’s
seat belt is fastened. At the same time, the chime sounds
for about 6 seconds unless the driver’s seat belt is securely
fastened.
 The seat belt warning light may also illuminate if the front passenger’s seat belt is
not fastened when the front passenger’s seat is occupied. For 5 seconds after the
ignition switch is in the ON position, the system does not activate the warning light
for the front passenger.
Refer to the Owner’s Manual for detailed information regarding seat belt usage.
FRONT-PASSENGER AIR BAG STATUS LIGHT
This vehicle is equipped with the Nissan Advanced Air Bag
system. Under some conditions, depending on pressure detected
on the passenger seat and how the seat belt is used, the front-
passenger air bag is designed to automatically turn OFF. When
the front-passenger air bag is OFF, the front-passenger air bag
status light will illuminate*. For example:
 When the system detects that the front-passenger’s seat is occupied by a small
adult, child or child restraint as outlined in the Owner’s Manual, the 2 will illuminate
to indicate that the front-passenger air bag is OFF and will not inflate in a crash.
 When the front-passenger’s seat is occupied and the passenger meets the
conditions outlined in the Owner’s Manual, the 2 will not illuminate to indicate that
the front-passenger air bag is operational.
*When the system detects that the front-passenger’s seat is unoccupied, the
passenger air bag status light will not illuminate even though the front-passenger
air bag is OFF.
Refer to the Owner’s Manual for detailed information regarding the Nissan Advanced Air
Bag System.

 To adjust the seatback, pull up on the lever 01 and lean back. This allows adjustment of the seatback for occupants of different sizes to help obtain proper seat belt fit.
To fold the 2nd row captain’s chair (if so equipped) flat for maximum cargo hauling:
 Remove the 2nd row center console (see “Console removal” in the “Instruments and controls” section of the Owner’s Manual).
 Pull the strap 02 located in the center of the seat cushion forward, and fold the seat cushion toward the front of the vehicle.
 Then lift up on the recline lever 01 to fold the seatback flat forward.
 Then fold the carpet panel flap 03 toward the back of the vehicle. (The carpet panel flaps provide a level cargo floor when the 3rd row seats are also folded flat.)
 Reverse this process to return the 2nd row captain’s chair to a seating position.
Make sure to properly raise the seatback to an upright position and push the seat cushion down into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
TIP UP FOR EASY ENTRY TO THE 3RD ROW
 The 2nd row outboard seats can be tipped forward for easy entry or exit from the 3rd
row bench seat. To enter the 3rd row, lift up on the latch 01 located on the upper
corner of the seatback on the 2nd row outboard seats and fold the seatback forward
at an angle at the seat base. This will release the back of the seat so it may be tipped
forward.
 Then lift up on the lower corner of the seat base and tip the 2nd row outboard seat
forward. To exit the 3rd row bench seat, lift up on the same latch and fold the
seatback forward onto the seat base. Then, lift up on the seat base and tip it forward.
FOLDING THE 3RD ROW SPLIT BENCH SEAT
 To fold the seats flat, disconnect and secure the center seat belt and tongues from the retractor base. Then pull up on the latch 01 located on the
outside corner of each seatback and fold the
seatback forward over the seat base.
 To raise the seats, lift the seatbacks and make sure they are fully latched in the upright position.
0102
03
01
0101