tow NISSAN ARMADA 2007 1.G Quick Reference Guide

WINDSHIELD WIPER/ WASHER SWITCH
0102*See your Owner’s Manual for more information.
STEERING WHEEL SWITCHES FOR AUDIO CONTROLHEADLIGHT AND TURN SIGNAL CONTROL
0304
FOUR-WHEEL DRIVE (4WD)

SHIFT SWITCH ( BEHIND STEERING WHEEL)CRUISE CONTROL
0506
STEERING WHEEL TILT ADJUSTMENT*HOOD RELEASE*
0708
CONTROL PANEL DISPL AY
09
AUDIO SYSTEM
10
FRONT-PASSENGER

AIR BAG STATUS

LIGHT
11
TIRE PRESSURE MONITORING SYSTEM ( BEHIND STEERING WHEEL)
07
0301
04
08
0205
06
09
11
13
12
10
CLIMATE

CONTROLS
12
TOW MODE SWITCH
13

HEADLIGHT AND TURN SIGNAL CONTROL
HEADLIGHT SWITCH
 Turn the headlight switch to the position to turn
on the front parking, tail, license plate and instrument
panel lights.
 Turn the headlight switch to the position to turn on
the headlights. All other lights remain on.
HIGH BEAM
 Push the headlight switch forward to select the high beam function. The blue
indicator light illuminates. Pull the headlight switch back to the original position to
select the low beam. The blue indicator light goes off.
 Pull and release the headlight switch to flash the headlight high beams on and off.
TURN SIGNAL SWITCH
 Move the headlight control switch up or down to signal the turning direction. When
the turn is completed, the turn signals cancel automatically.
 To signal a lane change, move the headlight control switch up or down to the point
where the indicator light begins to flash, but the headlight control switch does not
latch.
WINDSHIELD WIPER/WASHER SWITCH
 The ignition switch must be in the ON position
to activate the windshield wipers.
 Move the lever to the following positions to
operate the windshield wipers:
1A Intermittent (INT) – Front wipers operate
intermittently and can be further adjusted
by twisting the time control ring 1B.
02 Low Speed (LO) – Continuous low-speed
operation of front wipers.
03 High Speed (HI) – Continuous high-speed
operation of front wipers.
04 Mist (MIST) – Lift the lever up for one sweep of the front wipers.
05 Rear Wipers (REAR) – Twist the end section to operate the first (INT)
or second (ON) speed settings for the rear wipers.
 The washer function activates the washer fluid and several sweeps of the wipers:
• For F
RONT WASHER, pull lever toward you.
• For REAR WASHER, push lever away from you.

1A
02
03
04
1B05

TOW MODE SWITCH
Tow mode should be used when pulling a heavy trailer or hauling a heavy load. Using tow mode at other times may cause unnecessary transmission shifting and reduced fuel economy.
 Push the TOW MODE switch to activate tow mode. The indicator light on the TOW MODE switch illuminates when tow mode is selected.
 Push the TOW MODE switch again to turn tow mode off.
 Tow mode is automatically canceled when the key is turned off.
OUTSIDE MIRROR CONTROL SWITCH
POWER FOLDING MIRRORS (if so equipped)
 Move the switch 01 to select the left or right
mirror.
 Adjust each mirror to the desired position using
the switch 02.
 Push the switch 03 to fold both mirrors in
or out.
03
01
02
STEERING WHEEL SWITCHES FOR AUDIO
CONTROL (if so equipped)
 Press the POWER button to turn the audio system on or off.
 To choose preset radio stations A, B, C, CD or DVD AUX (if so equipped) press MODE repeatedly.
 The tuning up or down < >switch can be used to perform the following:
• Push the
< >switch for less than 1.5 seconds to change to a preset station.
• Push and hold the
< >switch for more than 1.5 seconds to seek to the next or previous broadcasting radio station.
• Push the
< >switch while playing a CD for less than 1.5 seconds to change tracks on the CD.
• If the vehicle is equipped with a CD changer, press and hold for more than 1.5
seconds to change between CDs.
CHILD SAFET Y DOOR LOCK
You’ll find the safety lock levers on the edge of the rear doors. When in
the LOCK position, the rear door can only be opened from the outside.

CONTROL PANEL DISPLAY WITH
N AVIGATION SYSTEM (if so equipped)
TRIP BUTTON
When the TRIP button is pressed, the following modes will display on the screen:
 Warning messages (if there are any)
 TRIP 1 (Elapsed Time, Driving
Distance, Average Speed)
 TRIP 2 (Elapsed Time, Driving
Distance, Average Speed)
 FUEL ECONOMY (Average Fuel Economy, Distance to Empty)
 MAINTENANCE (Engine Oil, Tire Rotation)
 OFF
MAINTENANCE ITEMS
You can set the engine oil and the tire rotation interval. To display the setting of the maintenance interval, select the ENGINE OIL or TIRE ROTATION key using the joystick and press the ENTER button.
To set the maintenance interval, select the MAINTENANCE SCHEDULE key by using the joystick and pushing the joystick to the right or left. To reset the maintenance interval, select the RESET key using the joystick and press the ENTER button.
CLOCK SET/ADJUSTMENT
The clock on the display screen can be adjusted using the joystick by the following procedure:  First select SYSTEM SETTINGS from the SETTINGS menu on the display screen.
 Next select CLOCK to enter the CLOCK SETTINGS mode.
 Then select the HOURS or MINUTES key and hold the joystick left or right to adjust
the time. After the desired time is shown on the display screen, press the BACK
button to store.
Refer to both the Navigation System Owner’s Manual and your Owner’s Manual for additional information.
SUNROOF CONTROLS (if so equipped)
TILTING THE SUNROOF  Push the tilt switch to the UP position 01 to tilt the

sunroof up.
 Push the tilt switch to the DOWN position 02 to tilt the sunroof down.
SLIDING THE SUNROOF  Push the switch toward the OPEN position 03 to fully

open the sunroof.
 Push the switch toward the CLOSE position 04 to fully close the sunroof.
 Push the switch in any direction while the sunroof is sliding open or closed to stop the sunroof in the desired position.
01
02
03
04

POWER LIFT GATE (if so equipped)
To operate the power lift gate, the automatic transmission lever must be in P (Park) and the glass hatch must be closed.
Power Open
 The lift gate can be opened by the button on the keyfob, the instrument panel switch and by the outside opener handle.
 The lift gate must be unlocked to open it with the outside opener handle.
Power Close
 The power close feature can be activated by the button on the keyfob, the instrument panel switch and the rear pillar switch.
 The keyfob button must be held for 0.5 seconds before the lift gate closes.
Cancel Switch
 The switch on the rear pillar cannot be used to open the lift gate. Pushing the switch toward the CANCEL position will disable the rear pillar switch.
 The lift gate can still be opened and closed using the switch on the instrument panel and the keyfob button.
 The lift gate can also be opened manually with the outside handle if the lift gate is
unlocked.
ADJUSTABLE ACCELERATOR AND BRAKE PEDALS
The accelerator and brake pedals can be adjusted for your driving comfort.
 Adjust the pedals when the automatic transmission lever is in P (Park).
 Push 01 to move the position of the pedals forward.
 Push 02 to move the position of the pedals backward.
01
02
TIRE PRESSURE MONITORING SYSTEM
This system monitors tire pressure. Please remember, this system
does not detect a sudden drop in tire pressure (for example, a
blowout while driving). It also does not monitor the air pressure in
the spare tire.
Tire pressure is affected by temperature. Low outside temperature
causes lower tire pressure. This may cause the low tire pressure
warning light to illuminate If the low tire pressure warning light illuminates, check the tire
pressure in all four tires.
To turn the low tire pressure warning light off, adjust the low tire pressure to the
recommended COLD tire pressure shown on the Tire and Loading Information label
located in the driver’s door opening.
If TPMS is not functioning properly, the low tire pressure warning light will flash for
approximately 60 seconds when the key is turned on. After 60 seconds, the light will
remain on. Have the system checked by a NISSAN dealer.

 To adjust the seatback, pull up on the lever 01 and lean back. This allows adjustment of the seatback for occupants of different sizes to help obtain proper seat belt fit.
To fold the 2nd row captain’s chair (if so equipped) flat for maximum cargo hauling:
 Remove the 2nd row center console (see “Console removal” in the “Instruments and controls” section of the Owner’s Manual).
 Pull the strap 02 located in the center of the seat cushion forward, and fold the seat cushion toward the front of the vehicle.
 Then lift up on the recline lever 01 to fold the seatback flat forward.
 Then fold the carpet panel flap 03 toward the back of the vehicle. (The carpet panel flaps provide a level cargo floor when the 3rd row seats are also folded flat.)
 Reverse this process to return the 2nd row captain’s chair to a seating position.
Make sure to properly raise the seatback to an upright position and push the seat cushion down into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
TIP UP FOR EASY ENTRY TO THE 3RD ROW
 The 2nd row outboard seats can be tipped forward for easy entry or exit from the 3rd
row bench seat. To enter the 3rd row, lift up on the latch 01 located on the upper
corner of the seatback on the 2nd row outboard seats and fold the seatback forward
at an angle at the seat base. This will release the back of the seat so it may be tipped
forward.
 Then lift up on the lower corner of the seat base and tip the 2nd row outboard seat
forward. To exit the 3rd row bench seat, lift up on the same latch and fold the
seatback forward onto the seat base. Then, lift up on the seat base and tip it forward.
FOLDING THE 3RD ROW SPLIT BENCH SEAT
 To fold the seats flat, disconnect and secure the center seat belt and tongues from the retractor base. Then pull up on the latch 01 located on the
outside corner of each seatback and fold the
seatback forward over the seat base.
 To raise the seats, lift the seatbacks and make sure they are fully latched in the upright position.
0102
03
01
0101