steering NISSAN FRONTIER 2007 D22 / 1.G Quick Reference Guide

steering wheel switches for audio control
instru Ment Brightness
control /tri P change Button
tire
Pressure
M onitoring s Y ste M (tPM s)
0203
05
hood release* front -Passenger
air Bag status light
cruise control
06
0809
four wheel dri Ve
(4 wd ) shift switch
cli
Mate controls
1112
02
06
04
03
01
11
05
1410
08
13
07
windshield wi Per /
washer switch
headlight and turn signal control
01
04
steering wheel tilt
ad Just Ment *
07
e-loc K switch
audio
s Y ste M
10
13
09
*See your Owner’s Manual for more information.
12
15
auXiliar Y audio
in Put Jac K *
hill
descent
control switch
1415

four-wheel driVe (4 wd) shift switch
(if so equipped)
 This system provides three positions so the driver can
select the desired drive mode according to driving
conditions.
 2WD – Dry, paved roads.
 4H – Rocky, sandy or snow-covered roads. (Before placing 4WD shift switch in 4H
position from 2WD, ensure vehicle speed is less than 62.5 MPH [100 km/h]).
 4LO – When maximum power and traction are required (steep grades, rocky, sandy or
muddy roads).
Intermittent – Wipers operate intermittently and can be adjusted by turning the
time control.
Low speed – Wipers operate at a continuous low speed.
High speed – Wipers operate at a continuous high speed.
Mist – Lift the lever up for one sweep operation of the wiper.
LCN0042
Wash – Pull the lever toward you. Wipers automatically wipe several times.
lo
hi
M ist
int
hill descent control switch
(if so equipped)
The hill descent control system is designed to reduce driver
workload when going down steep hills. The hill descent
control system helps to control vehicle speed so the driver can
concentrate on steering the vehicle.
To activate the hill descent control system:
 The automatic transmission selector lever must be in
forward or reverse gear,
 The 4WD switch must be in the 4L position and the vehicle speed must be under 15
MPH (25 km/h), or
 The 4WD switch must be in the 4H position and the vehicle speed must be under 21
MPH (35 km/h), and
 The hill descent control system switch must be on.
 The hill descent control indicator light will come on when the system is activated.
Also, the stop/tail lights illuminate while the hill descent control system applies the
brakes to control vehicle speed. To turn off the hill descent control system, push the
switch to the off position. The hill descent control system is temporarily disabled when
the brake or accelerator pedal is depressed.
Refer to your Owner’s Manual for detailed information.
H ILL S TART A SSIST (HSA) (
if so equipped)
The hill start assist system automatically keeps the brakes applied to help prevent the
vehicle from rolling backwards in the time it takes the driver to release the brake pedal
and apply the accelerator when the vehicle is stopped on a hill.

steering wheel switches for audio control
(if so equipped)
 Press the POWER button to turn the audio system on or
off.
 To choose preset radio stations A, B, C, CD and AUX
press MODE repeatedly.
 The tuning up or down switch can be used to perform
the following:
• Push the
switch for less than 1.5 seconds to change to a preset station.
• Push and hold the
switch for more than 1.5 seconds to seek the next or previous

broadcasting radio station.
• Push the
switch while playing a CD (if so equipped) for less than 1.5 seconds to

change tracks on the CD.
• If the vehicle is equipped with a CD changer, push and hold the
switch for more

than 1.5 seconds to change between CDs.
utilit Y Bed with sPra Y-on B ed liner
and utili -trac K ™ sY ste M (if so equipped)
The Utili-track™ channel system allows you to move
tie-down clamps in the bed to the best location to
secure a load.
 The tie-down cleats must be installed so the
clamp is properly seated in the notches in the
rail. If the tie-down cleat is not seated in the
notches, it will not be flush with the rail and
cannot be properly tightened. The bolt in the center of the cleat must be tightened
hand-tight (20 – 40 inch pounds).
 Check the tightness of the tie-down cleat periodically during a trip to make sure the
center bolt has not become loose.
 The channel end stoppers can be used to help prevent cargo from sliding or shifting
off the end of the truck bed. They must be installed so they are properly seated in the
detents in the channel.
Refer to your Owner’s Manual for loading limits and tie-down recommendations.
instru Ment B rightness control/tri P
change B utton
The instrument brightness control operates when the
headlight control switch is in the or position.
Turn the control to adjust the brightness of the
instrument panel lights.
Press the change button to select trip computer
features. See “Trip Computer” in the next column of this
Quick Reference Guide for more information.