ignition NISSAN FRONTIER 2008 D22 / 1.G Quick Reference Guide

REMOTE KEYLESS ENTRY SYSTEM (if so equipped)
LOCK DOORS
Press the
button to lock all doors.
UNLOCK DOORS
Press the
button once to unlock the driver’s door
only. Press thebutton againwithin 5seconds to
unlock all doors.
USING THE PANIC ALARM
Press andhold the
button forlonger than0.5seconds. Thepanic alarmwill
sound and the headlights will stay on for 25 seconds. The panic alarm stops when it
has run for 25 seconds or when any button is pressed on the keyfob.
SILENCING THE HORN BEEP FEATURE
 To deactivate: Press and hold theandbuttons for at least 2 seconds.
 To activate: Press and hold the
andbuttons for at least 2 seconds.
WINDSHIELD WIPER/WASHER SWITCH
The ignition switchmustbeinthe ON position to
activate the windshield wipers.
 Move thelever tothe following positions tooperate
the windshield wipers:
Intermittent (INT)–Front wipers operate inter-
mittently and can be further adjusted by twisting
the time control ring
.
Low Speed (LO)– Continuous low-speed operation of front wipers.
High Speed (HI)– Continuous high-speed operation of front wipers.
Mist (MIST) – Lift the lever up for one sweep of the front wipers.
 Pull the lever toward you to activate front washer fluid and several sweeps of the wipers.
2

HEADLIGHT AND TURN SIGNAL CONTROL
TO ACTIVATE THE AUTOLIGHT SYSTEM (if so
equipped):
Turn the headlight control switchto the AUTO position to
activate the autolight system. The autolight system can:
 Turn the headlights on automatically when it is dark.
 Turn the headlights off automatically when it is light.
 Keep the headlights on for 45 seconds after you turn the ignition switch to OFFand all
doors are closed.
TO DEACTIVATE THE AUTOLIGHT SYSTEM:
 Turn the headlight control switchto the OFF,orposition.
HEADLIGHT CONTROL SWITCH
Turn the headlight control switchto theposition to turn on the front parking,
tail, license plate and instrument panel lights.
 Turn the headlight control switch
to theposition to turn on the headlights. All
other lights remain on.
FOG LIGHT OPERATION (if so equipped)
 Turn the switch (inside collar)to theposition to turn on the fog lights.
 Turn the switch (inside collar)
to the OFFposition to turn off the fog lights.
TURN SIGNAL SWITCH
Move theheadlight controlswitchupordownto
signal a turning direction. When the turn is completed,
the turn signals cancel automatically.
 To signal alane change, movetheheadlight control
switch up or down
to the point where the indicator
light begins to flash, but the headlight control switch does not latch.
HIGH BEAM
 Push the headlight control switch forwardto select
the high beam function. Theblue
indicator light
illuminates. Pull the headlight switch back to the original
position to select the low beam. The blue
indicator
light goes off.
 Pull and release the headlight control switch
to flash the headlight high beams on
and off.
3

LOAD BUTTON
 LOAD A SINGLE DISC - Press the
button for less than 1.5 seconds. Select the
loading slot by pressing one of the CD insert select button ( 1-6 ) , then insert the CD.
 LOAD UP TO 6 DISCS - Press and hold the
button for more than 1.5 seconds.
The slot numbers (1-6) will illuminate on the display when CDs are loaded into the
changer.
*XM  Satellite Radioisonly available onvehicles equipped withoptional XMsatellite
subscription service.
CLOCK SET/ADJUSTMENT
 Press and hold the DISP CLOCKbutton until it beeps. The hours will start flashing.
 Press the CAT/FOLDER orSEEK/TRACK button to adjust the hours.
 Press the DISP CLOCK button to switch to the minute adjustment.
 Press the CAT/FOLDER orSEEK/TRACK button to adjust the minutes.
 Press the DISP CLOCK button to store the time and exit clock set mode.
TRIP COMPUTER (if so equipped)
The trip computer readout is in the speedometer display. With
theignition keyinthe ON position orthe vehicle running, you
can select anitem bypressing theCHANGE buttononthe
instrument panel. It can show the following items:
 TRIP “A” – Measures the distance of one specific trip.
 TRIP “B” – Measures the distance of a second specific trip.
 DISTANCE TOEMPTY (dte)–Estimates thedistance thatcanbedriven before
refueling.
 AVERAGE SPEED (mph or km/h) – Shows the average speed since the last reset.
 AVERAGE FUELCONSUMPTION (mpgorL/100km) –Shows theaverage fuel
consumption since the last reset.
 JOURNEY TIME – Shows the time since the last reset.
 RESET – Press the CHANGE button on the instrument panel for more than 1 second to
reset the trip odometer to zero.
INSTRUMENT BRIGHTNESS CONTROL/TRIP CHANGE BUTTON
 The instrument brightness controloperates whentheheadlight
control switch is in the
orposition.
 Turn thecontrol toadjust thebrightness ofthe instrument panel
lights.
 Press the change button to select trip computer features.
8

When the front-passenger’s seat is occupied and the passenger meets the conditions
outlined inthe Owner’s Manual,the
willnotilluminate toindicate thatthe
front-passenger air bag is operational.
*When thesystem detects thatthefront-passenger’s seatisunoccupied, the
passenger air bag status light will not illuminate even though the front-passenger
air bag is OFF.
TIRE PRESSURE MONITORING SYSTEM (TPMS)
This system monitors tirepressure. Ifthe low tirepressure warning
light illuminates, check the tire pressure in all four tires.
Adjust the low tire pressure to the recommended COLD tire pressure
shown on the Tire and Loading Information label located in the driver’s
door opening. After tire pressures are adjusted, the vehicle will need
to be driven at speeds above 16 MPH (25 km/h) to activate the TPMS
and turn off the low tire pressure warning light.
SEAT BELT WARNING LIGHT AND CHIME
 The light and chime remind you to fasten your seat belts. The light
illuminates whenevertheignition keyisturned tothe ON or
START position andremains illuminated untilthedriver’s seat
belt is fastened. At the same time, the chime sounds for approxi-
mately 6seconds unlessthedriver’s seatbeltissecurely fas-
tened.
 The seat beltwarning lightmayalso illuminate ifthe front pas-
senger’s seatbeltisnot fastened whenthefront passenger’s
seat is occupied (if so equipped) . For 7 seconds after the ignition switch is in the ON
position, the system does not activate the warning light for the front passenger.
CHILD SAFETY REAR DOOR LOCK (Crew Cab model only)
Child safety locks help prevent the rear doors from being opened acci-
dentally, especially when small children are in the vehicle. The child safety
lock levers are located on the edge of the rear doors. When the lever is in
the LOCK position, the door can only be opened from the outside.
11

MOONROOF CONTROLS (if so equipped)
The ignition switch must be in the ON position to operate the
moonroof controls.
TILTING THE MOONROOF
 To tiltthe moonroof up,first close themoonroof by
pushing theswitch toward UP/CLOSE
.Release
the switch, then push the UP/CLOSEswitch again to tilt
the moonroof up.
 To tiltthe moonroof down,pushtheswitch toward
DOWN/OPEN
.
SLIDING THE MOONROOF
 To fully open the moonroof, push the switch toward DOWN/OPEN. To open the
moonroof part way, push the switch in any direction while the moonroof is sliding to stop
it in the desired position.
 To fully close themoonroof, pushtheswitch toward UP/CLOSE
.To close the
moonroof part way, push the switch in any direction while the moonroof is sliding to stop
it in the desired position.
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull uponthe lever under thefront ofthe
seat and slide backward or forward; release.
 Lift the lever
on the side of the seat to
adjust yourseatback forwardorbackward;
release when you have found a comfortable
angle and the seat belt fits properly.
 Turn either dial
to adjust the angle and
height of the seat cushion to the desired position.
With power seats (if so equipped):
 Move the control
forward or backward to adjust the seat
cushion forward or backward.
 Pull uponthe control
toraise theseat cushion; push
down to lower the cushion.
 Push the switch
forward to move the seatback forward;
push it back to move the seatback backward.
Lumbar Support (if so equipped)
Your driver’s seathasalumbar support; adjustitby moving the
lever
up or down.
12

NOTE:Onceyouhave pressed andreleased theprogram buttononthe garage
door opener’s motor and the “training light” is lit, you have 30 seconds in which to
perform step 7. Use the help of a second person for convenience to assist when
performing this step.
7.Quickly within30seconds ofpressing andreleasing thegarage dooropener
program button,firmlypress andrelease theHomeLink button you’vejustpro-
grammed. Press and release the HomeLink button up to three times to complete the
training.
8. Your HomeLink button should nowbeprogrammed. (Toprogram theremaining
HomeLink buttons for additional door or gate openers, follow steps 2-8 only) .
BLUETOOTH HANDS-FREE PHONE SYSTEM (if so equipped)
Withanoverhead microphone andsound
transmitted throughtheaudio system
speaker, theBluetooth Hands-Free Phone
System utilizes Bluetooth wireless technol-
ogy and voice recognition to provide hands-
free cellular phone communication.
SYSTEM OPERATING TIPS
 Close allwindows. Surrounding noises
may interfere with system operation and
performance.
 Press the
button on the steering wheel to activate voice recognition.
 Wait for the tone before speaking.
 Begin speaking a command within 5 seconds of the tone.
 To go back to the previous command, say “Go back” or “Correction.”
 To cancel a voice recognition session, simply wait 5 seconds, say “Cancel” or “Quit,” or
press the
button.
 To increase or decrease the volume of the voice prompts, push the VOL (volume) control
switch up or down on the steering wheel or turn the VOLknob on the audio system while
the system is responding.
 Speak in a clear and natural voice without pausing between words.
 Ifthe Voice Recognition systemdoesnotrecognize yourvoice commands, trainthe
system using the Speaker Adaptation Mode.
 Some commands are not available while the vehicle is in motion.
 The “Help” command can be used in any menu to hear a list of available commands.
 For recommended phones and detailed instructions, please visit
www.nissanusa.com/bluetooth.
PAIRING YOUR PHONE
To use thehands-free feature,youneed toset-up, orpair, thesystem torecognize your
cellular phone(s) . 5Bluetooth -enabled phonescanbepaired. Afterset-up, thesystem
automatically connects with a paired phone when the ignition is in the ACC or ON position,
as long as the phone is on and in the vehicle.
15