instrument panel NISSAN FRONTIER 2008 D22 / 1.G Quick Reference Guide

HEADLIGHT AND TURN SIGNAL CONTROL
TO ACTIVATE THE AUTOLIGHT SYSTEM (if so
equipped):
Turn the headlight control switchto the AUTO position to
activate the autolight system. The autolight system can:
 Turn the headlights on automatically when it is dark.
 Turn the headlights off automatically when it is light.
 Keep the headlights on for 45 seconds after you turn the ignition switch to OFFand all
doors are closed.
TO DEACTIVATE THE AUTOLIGHT SYSTEM:
 Turn the headlight control switchto the OFF,orposition.
HEADLIGHT CONTROL SWITCH
Turn the headlight control switchto theposition to turn on the front parking,
tail, license plate and instrument panel lights.
 Turn the headlight control switch
to theposition to turn on the headlights. All
other lights remain on.
FOG LIGHT OPERATION (if so equipped)
 Turn the switch (inside collar)to theposition to turn on the fog lights.
 Turn the switch (inside collar)
to the OFFposition to turn off the fog lights.
TURN SIGNAL SWITCH
Move theheadlight controlswitchupordownto
signal a turning direction. When the turn is completed,
the turn signals cancel automatically.
 To signal alane change, movetheheadlight control
switch up or down
to the point where the indicator
light begins to flash, but the headlight control switch does not latch.
HIGH BEAM
 Push the headlight control switch forwardto select
the high beam function. Theblue
indicator light
illuminates. Pull the headlight switch back to the original
position to select the low beam. The blue
indicator
light goes off.
 Pull and release the headlight control switch
to flash the headlight high beams on
and off.
3

STEERING WHEEL SWITCHES FOR AUDIO CONTROL/
BLUETOOTH (if so equipped)
Press the MODEbutton to turn the radio system on.
 To choose PresetA,B, C, CD, AUX orXM (if so equipped)
press MODE repeatedly.
 The tuning up or down
switch can be used to perform the
following:
● Push the
switch for less than 1.5 seconds to change to a
preset station.
● Push and hold the
switch for more than 1.5 seconds to seek the next or previous
broadcasting radio station.
● Push the
switch while playing a CD (if so equipped) for less than 1.5 seconds to
change tracks on the CD.
● If the vehicle is equipped with a CD changer, push and hold the
switch for more
than 1.5 seconds to change between CDs.
 Push the VOLcontrol switch up or down to increase or decrease the volume.
CRUISE CONTROL (if so equipped)
To activate thecruise control, pushtheON·OFF switch.The
indicator light in the instrument panel will illuminate.
 To set cruising speed,accelerate thevehicle tothe desired
speed, pushthe COAST/SET switchandrelease it.The SET
indicator light in the instrument panel will illuminate.
 To reset atafaster cruising speed,pushandhold the
ACCEL/RES switch.Whenthevehicle attainsthespeed you
desire, release the switch.
 To reset at a slower cruising speed, push and hold the COAST/SETswitch. Release the
switch when the vehicle slows to the desired speed.
 Tocancel cruisecontrol, pushtheCANCEL switchortap thebrake pedal. TheSET
indicator light in the instrument panel will go out.
 To resume apreset speed, pushandrelease theACCEL/RES switch.Thevehicle
returns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h) .
 To turn off cruise control, push the ON·OFFswitch. Both the CRUISE indicator light and
the SET indicator light in the instrument panel will go out.
4

LOAD BUTTON
 LOAD A SINGLE DISC - Press the
button for less than 1.5 seconds. Select the
loading slot by pressing one of the CD insert select button ( 1-6 ) , then insert the CD.
 LOAD UP TO 6 DISCS - Press and hold the
button for more than 1.5 seconds.
The slot numbers (1-6) will illuminate on the display when CDs are loaded into the
changer.
*XM  Satellite Radioisonly available onvehicles equipped withoptional XMsatellite
subscription service.
CLOCK SET/ADJUSTMENT
 Press and hold the DISP CLOCKbutton until it beeps. The hours will start flashing.
 Press the CAT/FOLDER orSEEK/TRACK button to adjust the hours.
 Press the DISP CLOCK button to switch to the minute adjustment.
 Press the CAT/FOLDER orSEEK/TRACK button to adjust the minutes.
 Press the DISP CLOCK button to store the time and exit clock set mode.
TRIP COMPUTER (if so equipped)
The trip computer readout is in the speedometer display. With
theignition keyinthe ON position orthe vehicle running, you
can select anitem bypressing theCHANGE buttononthe
instrument panel. It can show the following items:
 TRIP “A” – Measures the distance of one specific trip.
 TRIP “B” – Measures the distance of a second specific trip.
 DISTANCE TOEMPTY (dte)–Estimates thedistance thatcanbedriven before
refueling.
 AVERAGE SPEED (mph or km/h) – Shows the average speed since the last reset.
 AVERAGE FUELCONSUMPTION (mpgorL/100km) –Shows theaverage fuel
consumption since the last reset.
 JOURNEY TIME – Shows the time since the last reset.
 RESET – Press the CHANGE button on the instrument panel for more than 1 second to
reset the trip odometer to zero.
INSTRUMENT BRIGHTNESS CONTROL/TRIP CHANGE BUTTON
 The instrument brightness controloperates whentheheadlight
control switch is in the
orposition.
 Turn thecontrol toadjust thebrightness ofthe instrument panel
lights.
 Press the change button to select trip computer features.
8

FOUR-WHEEL DRIVE (4WD) SHIFT SWITCH (if so equipped)
This system provides three positions so the driver can select
the desired drive mode according to driving conditions.
 2WD – Dry, paved roads.
 4H –Rocky, sandyorsnow-covered roads.(Before placing
4WD shiftswitch in4H position from2WD, ensure vehicle
speed is less than 62.5 MPH [100 km/h]) .
 4LO – When maximum power and traction are required (steep
grades, rocky, sandy or muddy roads) .
NOTE: The vehicle must be stopped and in N (Neutral) with the brake pedal depressed when
shifting into and out of 4LO.
VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH (if so equipped)
The Vehicle Dynamic Control (VDC) system is designed to help improve
driving stability. VDC detects wheel spin and controls braking and engine
output. VDC may need to be temporarily shut off if you are trying to free a
vehicle stuck in snow or mud.
 Push the Vehicle Dynamic Control (VDC) off switch to deactivate the
VDC system. The
lightwillilluminate inthe instrument panel
gauge area.
 Push the Vehicle Dynamic Control (VDC) off switch again to activate the VDC system.
The
light in the instrument panel gauge area will turn off.
 The VDC system is active while the vehicle is running until the switch is pressed to turn
it off.
E-LOCK SWITCH (if so equipped)
The Electronic LockingRearDifferential (E-Lock)systemcan
help provide addedtraction ifthe vehicle isstuck orbecoming
stuck.
To activate the system:
 The 4WD switch must be in the 4LO position (4-wheel drive
vehicles) ,
 The vehicle must be stopped or moving at 4 mph or less, and
 The E-Lock system switch must be turned on.
Once the vehicle is free, the system should be turned off.
9