NISSAN GT-R 2021 Owners Manual

,
or
button)HAZARD -
twice
HORN - once HAZARD -
once
HORN - none HAZARD - none
HORN - none

,
or
button)HAZARD -
twice HAZARD - none HAZARD - none
Switching procedureThe horn beep feature can be deactivated
with the following procedures.
1. Push the LOCK
and UNLOCK
buttons simultaneously for more than
2 seconds.
2. The hazard indicator flashes 3 times.
3. The horn beep feature will be deacti- vated (Hazard indicator mode).
4. To reactivate the horn beep feature (Hazard indicator and horn mode),
push the buttons once more. The
hazard indicator flashes once and
the horn beeps once.

position.Shift the shift lever to the
position.
When opening the driver

located below the instrument panel.
The hood will then spring up slightly.
2. Pull the lever
at the front of the
hood with your fingertips and raise
the hood.
3. Grasp the insulated part of the stay
and release it from the hook, then
securely insert it into the hood hole
.

CLOSING THE HOOD1. While supporting the hood, store thestay to the original position.
2. Slowly lower the hood. When it is at a height of 1 ft (30 cm) or higher, drop
the hood and make sure that both
sides of the hood securely lock in
place.
CAUTION
When closing the hood, lower it
slowly so that hands or other items
do not get caught.
NOTE:
Because the hood of this vehicle re-
quires more force to close than that for
other vehicles, the hood will be difficult
to close if you lower it all the way and
then attempt to press it closed. Be sure
to drop the hood from a height of
approximately 1 ft (30 cm) and be sure
that both sides securely lock in place.Pre-driving checks and adjustments
3-19

Do not use the cruise control when
driving under the following condi-
tions. Doing so could cause a loss of
vehicle control and result in an acci-
dent.
.When it is not possible to keep
the vehicle at a set speed.
. In heavy traffic or in traffic that
varies in speed.
. On winding or hilly roads.
. On slippery roads (rain, snow, ice,
etc.).
. In very windy areas.
NOTE:
. When the SAVE mode is selected
with the transmission setup switch,
the acceleration and deceleration
can be controlled smoothly. When
the SAVE mode is selected, the
maximum setting speed is lower
than the one in the normal mode. When the vehicle approaches a gen-
tle uphill, there may be a slight delay
as the vehicle returns to the preset
speed. However, the vehicle will
gradually accelerate and return to
the preset speed.
PRECAUTIONS ON CRUISE CON-
TROL.
If the cruise control system malfunc-
tions, it will cancel automatically. The
SET indicator will blink and the cruise
control system warning will appear to
warn the driver. (
“Cruise control
system warning” page 2-43)
. If the engine coolant temperature
becomes excessively high, the cruise
control system will be canceled auto-
matically.
. If the SET indicator blinks, turn the
cruise control main switch off and it is
recommended you contact a GT-R
Starting and driving
5-35
CRUISE CONTROL

2. Accelerate your vehicle to the desiredspeed, push the SET/COAST switch
and release it. (The SET indicator will
illuminate in the meter.) Take your
foot off the accelerator pedal. Your
vehicle will maintain the set speed.
NOTE:
If the vehicle speed reaches approxi-
mately 3 MPH (5 km/h) over the set
speed, the set speed on the vehicle
information display blinks.Passing another vehicleTo pass another vehicle, depress the
accelerator pedal. When you release the
pedal, the vehicle will return to the pre- viously set speed.
Increasing the set vehicle speedTo reset at a faster cruising speed, use
one of the following methods:
.
Depress the accelerator pedal. When
the vehicle attains the desired speed,
push and release the SET/COAST
switch.
. Push and hold the RESUME/ACCELER-
ATE switch. When the vehicle attains
the speed you desire, release the
switch.
. Push and then quickly release the
RESUME/ACCELERATE switch. Each
time you do this, the set speed will
increase by about 1 MPH or 1 km/h.Decreasing the set vehicle speedTo reset at a slower cruising speed, use
one of the following methods:
.Lightly tap the brake pedal. When the
vehicle attains the desired speed,
push and release the SET/COAST
switch.
. Push and hold the SET/COAST switch.
Release the switch when the vehicle
slows down to the desired speed.
. Push and then quickly release the
Starting and driving
5-37