brake light NISSAN GT-R 2021 Repair Manual

of each nut lightly
contacts the seat part
of the wheel
hole.
When replacing a front wheel, make
sure the hole in the wheel is aligned
with the pin on the brake disc rotor.
8. With the wheel nut wrench, tighten wheel nuts alternately and evenly in
the sequence illustrated (
,
,
,
,
)
until they are tight.
9. Lower the vehicle slowly until the tire touches the ground. Then, with the
wheel nut wrench, tighten the wheel
nuts securely in the sequence as
illustrated. Lower the vehicle comple-
tely.
WARNING
If the road wheels are hot, allow
them to cool sufficiently before tigh-
tening the wheel nuts. Otherwise, the
wheel nuts cannot be tightened to
specification.
NOTE:.
As soon as possible, tighten the
wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque:
Do-it-yourself
8-45

In-cabin microfilter .................................................... 4-13
Increasing fuel economy ...................................... 5-42
Indicators and display ............................................. 5-36
Infants .................................................................................. 1-13
Injured persons ................................................................. 1-9
Inside mirror ................................................................... 3-27
Inspection and adjustments
after driving ............................................................... GTR-19
Inspection and adjustments
before driving .......................................................... GTR-14
Installing front license plate ............................ 10-16
Installing top tether strap .................... 1-26, 1-30
Instrument brightness control ......................... 2-12
Instrument panel ............................................................ 2-5
Intelligent Key .................................................................... 3-2
Intelligent Key battery discharge ................... 5-12
Intelligent Key battery
discharge indicator ................................................... 2-48
Intelligent Key battery replacement ............ 8-25
Intelligent Key functions ........................................... 3-9
Intelligent Key insertion indicator ................. 2-47
Intelligent Key removal indicator ................... 2-47
Intelligent Key system ................................................. 3-8
Interior light control switch ................................ 2-70
Interior lights .................................................................. 2-69
J
Jacking vehicle and removing wheels....... 8-41
Jump starting ..................................................... 6-5, 8-15
K
Key
Intelligent Key ............................................................ 3-2
Intelligent Key battery discharge ............ 5-12
Intelligent Key battery
discharge indicator ............................................ 2-48
Intelligent Key battery replacement ..... 8-25
Intelligent Key functions ................................... 3-9
Intelligent Key insertion indicator .......... 2-47
Intelligent Key removal indicator ............ 2-47
Intelligent Key system ......................................... 3-8
Keys ................................................................................... 3-2
Locking with mechanical key ....................... 3-6
No key warning ..................................................... 2-45
Remote keyless entry system ................... 3-12
L
M
Maintenance
Brake system (NCCB (NISSAN Carbon
Ceramic Brake)) ..................................................... 8-20
Explanation of maintenance items .......... 9-3

General maintenance ............................... 9-2, 9-3
Maintenance information ........................... GTR-3
Maintenance precautions ................................ 8-3
Maintenance requirement ............................... 9-2
Readiness for
Inspection/Maintenance test ................. 10-22
Scheduled maintenance ................................... 9-2
Seat belt maintenance .................................... 1-12
Maintenance log and records .......................... 9-28
Map lights ......................................................................... 2-69
Measurement of weights .................................. 10-19
Meters and gauges ....................................................... 2-6
Mirror
Inside mirror ............................................................ 3-27
Mirrors ........................................................................... 3-27
Outside mirrors ..................................................... 3-28
Vanity mirror ........................................................... 3-29
Vanity mirror lights ............................................ 2-71
Most common factors contributing to
vehicle corrosion ............................................................. 7-9
Multi Function Display Owner’s Manual ....... 4-2
N
NCCB (NISSAN Carbon
Ceramic Brake) ........................................... GTR-6, 8-20
Replacing brake pads and brake
disc rotors ................................................................. 8-21
NISSAN Advanced Air Bag System ................ 1-40
NISSAN Vehicle Immobilizer System ............ 2-50
No key warning ............................................................ 2-45 Noises are heard while driving .................. GTR-26
Normal mode ................................................................. 5-25
O
P

Self-adjusting brakes ............................................... 8-19
Servicing air conditioner ....................................... 4-14
Setting (drive computer) ....................................... 2-20
Setting guide of wheel alignment
depending on the customer’s driving ........ 9-21
Setting hazard indicator and
horn mode ....................................................................... 3-14
Shift lever position warning ............................... 2-37
Shift “P” warning .......................................................... 2-46
Small children ................................................................ 1-14
Sonar system ................................................................. 5-48
Sonar system off switch ....................................... 2-59
Sonar system setting .............................................. 5-50
Spark plugs ...................................................................... 8-16
Special winter equipment .................................... 5-57
Specifications ................................................................. 10-9
Speedometer ...................................................................... 2-7
StartingBefore starting the engine ........................... 5-13
Jump starting ............................................. 6-5, 8-15
Precautions when starting
and driving ................................................................... 5-3
Push starting .............................................................. 6-8
Starting the engine ............................................ 5-14
Steering
Power steering ....................................................... 5-51
Power steering fluid .......................................... 8-11
Steering lock release
malfunction indicator ....................................... 2-47
Steering wheel ....................................................... 3-26
Steering-wheel-mounted controls ........ 5-36 Tilt/telescopic steering column ............... 3-26
Storage ............................................................................... 2-63
Summer tires ............................................................ GTR-11
Sun visors .......................................................................... 3-27
Sunglasses holder ...................................................... 2-64
Supplemental air bag warning labels ........ 1-48
Supplemental air bag warning light ............ 1-48
Supplemental restraint system ....................... 1-34
Suspension and
wheel alignment .............................. GTR-16, GTR-23
Switch Hazard warning flasher switch .................... 6-2
Headlight and turn signal switch ........... 2-53
Headlight switch ................................................... 2-53
How to switch the modes ............................ 5-26
Ignition switch operation .............................. 5-11
Ignition switch positions ................................ 5-11
Interior light control switch ......................... 2-70
Locking with power door lock switch ..... 3-5
Push-button ignition switch ....................... 5-10
Rear window defroster switch .................. 2-52
Trunk lid release switch ................................. 3-20
Trunk open request switch ......................... 3-20
Trunk release power cancel switch ...... 3-21
VDC, transmission and suspension
setup switches ....................................................... 5-25
Wiper and washer switch .............................. 2-51
T

of each nut lightly
contacts the seat part
of the wheel
hole.
When replacing a front wheel, make
sure the hole in the wheel is aligned
with the pin on the brake disc rotor.
8. With the wheel nut wrench, tighten wheel nuts alternately and evenly in
the sequence illustrated (
,
,
,
,
)
until they are tight.
9. Lower the vehicle slowly until the tire touches the ground. Then, with the
wheel nut wrench, tighten the wheel
nuts securely in the sequence as
illustrated. Lower the vehicle comple-
tely.
WARNING
If the road wheels are hot, allow
them to cool sufficiently before tigh-
tening the wheel nuts. Otherwise, the
wheel nuts cannot be tightened to
specification.
NOTE:.
As soon as possible, tighten the
wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque:
Do-it-yourself
8-45

position
.
2. Push the ignition switch to the ON position.
3. The autolight system automatically turns the headlights on and off.
To turn the autolight system off, turn the
switch to the
position.
The autolight system can turn on the
headlights automatically when it is dark and turn off the headlights when it is
light.
If the ignition switch is pushed to the ON
position when the parking brake is ap-
plied, the headlights remain off.
With the
position selected, the head-
lights turn off when the ignition switch is
pushed to the OFF position, the shift lever
is placed in the
position or the parking
brake is applied. (The parking, side mar-
ker, tail, license plate, and instrument
lights are on.)
With the AUTO position selected (head-
lights are on), the headlights will remain
on for 45 seconds when the ignition
switch is placed in the OFF position and
one of the doors is opened.
Instruments and controls
2-55

of each nut lightly
contacts the seat part
of the wheel
hole.
When replacing a front wheel, make
sure the hole in the wheel is aligned
with the pin on the brake disc rotor.
8. With the wheel nut wrench, tighten wheel nuts alternately and evenly in
the sequence illustrated (
,
,
,
,
)
until they are tight.
9. Lower the vehicle slowly until the tire touches the ground. Then, with the
wheel nut wrench, tighten the wheel
nuts securely in the sequence as
illustrated. Lower the vehicle comple-
tely.
WARNING
If the road wheels are hot, allow
them to cool sufficiently before tigh-
tening the wheel nuts. Otherwise, the
wheel nuts cannot be tightened to
specification.
NOTE:.
As soon as possible, tighten the
wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque:
Do-it-yourself
8-45

The Vehicle Dynamic Control (VDC) sys-
tem uses various sensors to monitor
driver inputs and vehicle motion. Under
certain driving conditions, the VDC sys-
tem helps to perform the following func-
tions.
.Controls brake pressure to reduce
wheel slip on one slipping drive wheel
so power is transferred to a non
slipping drive wheel on the same axle.
. Controls brake pressure and engine
output to reduce drive wheel slip
based on vehicle speed (traction con-
trol function).
. Controls brake pressure at individual
wheels and engine output to help the
driver maintain control of the vehicle
in the following conditions:
— understeer (vehicle tends to not
follow the steered path despite
increased steering input)
— oversteer (vehicle tends to spin due to certain road or driving condi-
tions).
The VDC system can help the driver to
maintain control of the vehicle, but it
cannot prevent loss of vehicle control in
all driving situations.
When the VDC system operates, the VDC
warning light
in the meter flashes so note the following:
.
The road may be slippery or the
system may determine some action
is required to help keep the vehicle on
the steered path.
. You may feel a pulsation in the brake
pedal and hear a noise or vibration
from under the hood. This is normal
and indicates that the VDC system is
working properly.
. Adjust your speed and driving to the
road conditions.
. The VDC mode can be changed using
the VDC setup switch. (
“VDC,
transmission and suspension setup
switches” page 5-25)
(
“Vehicle Dynamic Control (VDC)
warning light” page 2-34,
“Vehicle
Dynamic Control (VDC) off indicator light”
page 2-33)
If a malfunction occurs in the system, the
VDC warning light
illuminates in the
meter. The VDC system automatically
turns off.
The VDC setup switch is used to turn off
the VDC system. The VDC off indicator
illuminates to indicate the VDC sys-
tem is off.
When the VDC setup switch is used to
turn off the system, the VDC system still
VEHICLE DYNAMIC CONTROL (VDC) SYSTEM

operates to prevent one drive wheel from
slipping by transferring power to a non
slipping drive wheel. The VDC warning
light
will not flash. The VDC
system is automatically reset to on when
the ignition switch is placed in the off
position then back to the on position.
(
“Vehicle Dynamic Control (VDC)
warning light” page 2-34,
“Vehicle
Dynamic Control (VDC) off indicator light”
page 2-33)
The computer has a built-in diagnostic
feature that tests the system each time
you start the engine and move the vehicle
forward or in reverse at a slow speed.
When the self-test occurs, you may hear a
“clunk” noise and/or feel a pulsation in the
brake pedal. This is normal and is not an
indication of a malfunction.
may illuminate.
. If brake related parts such as
brake pads, rotors and calipers
are not standard equipment or
are extremely deteriorated, the
VDC system may not operate
properly and the VDC warning
light
may illuminate.
. If engine control related parts are
not standard equipment or are
extremely deteriorated, the VDC
warning light
may illuminate.
. When driving on extremely in-
clined surfaces such as higher
banked corners, the VDC system
may not operate properly and the
VDC warning light
may illumi-
nate. Do not drive on these types of roads.
. When driving on an unstable sur-
face such as a turntable, ferry,
elevator or ramp, the VDC warn-
ing light
may illuminate. This
is not a malfunction. Restart the
engine after driving onto a stable
surface.
. If wheels or tires other than the
those recommended are used,
the VDC system may not operate
properly and the VDC warning
light
may illuminate.
. The VDC system is not a substi-
tute for winter tires or tire chains
on a snow covered road.
NOTE:
. Always make sure the VDC is ON
before driving the vehicle by check-
ing that the VDC OFF indicator lights
on the meter and the VDC set-up
switch are not illuminated.
The GT-R is a high performance
vehicle and the VDC must be on/
activated to provide proper power-
train operation and intended driva-
bility.Starting and driving
5-55

, position the two vehicles (
and
) to bring their batteries into
close proximity to each other. Do not
allow the two vehicles to touch.
2. Apply parking brake. Move the shift lever to the
position. Switch off all unnecessary electrical systems (light,
heater, air conditioner, etc.).
3. Remove the battery cover. Cover the battery with a firmly wrung out moist
cloth to reduce explosion hazard.
4. Connect jumper cables in the se- quence as illustrated (
?
?
CAUTION
.Always connect positive (+) to
positive (+) and negative (−) to
body ground (as illustrated), not
to the battery.
. Make sure that the jumper cables
do not touch moving parts in the
engine compartment and that
clamps do not contact any other
metal.
5. Start the engine of the booster vehicle
and let it run for a few minutes.
6. Keep the engine speed of the booster
In case of emergency
6-7