lock NISSAN GT-R 2022 Owners Manual

ANTI-LOCK BRAKING SYSTEM
(ABS) WARNINGThis will appear if the Anti-lock Braking
System (ABS) is not functioning properly.
(
“Anti-lock Braking System (ABS)
warning light” page 2-29) (
“Brake
warning light” page 2-26)
“Vehicle Dynamic Control (VDC)
warning light” page 2-34) (
“Vehicle
Dynamic Control (VDC) off indicator light”
page 2-33)
“All-Wheel Drive (AWD) warning light”
page 2-29)
NOTE:
If the vehicle is driven in a way which
causes the rear wheels to slip, the AWD
clutch temperature will increase and
the warning indicator may flash. Con-
tinuing to drive in way that causes the
warning light to flash may cause the
clutch to reach excessive temperatures

headlights are turned off.
2. Open the engine hood and remove the cover on the battery and the fuse/
fusible link holder.
3. Remove the fuse/fusible link holder cover.
4. Remove the fuse with the fuse puller that is located in the engine compart-
ment fuse box.
, replace it with a
new fuses
. Spare fuses are stored in
the passenger compartment fuse box.
6. If a new fuse also opens, have the electrical system checked and re-
paired. It is recommended you contact
a GT-R certified NISSAN dealer.
Fusible linksIf any electrical equipment does not
operate and fuses are in good condition,
check the fusible links. If any of these
fusible links are melted, replace only with
genuine NISSAN parts.
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified
on the fuse box cover. This could
damage the electrical system or
electronic control units or cause a
fire.
If any electrical equipment does not
operate, check for an open fuse.
1. Be sure the ignition switch is pushed to the OFF or LOCK position and the
Do-it-yourself
8-23

ENGINE COMPARTMENT
WARNING
Never use a fuse of a higher or lower
amperage rating than that specified
on the fuse box cover. This could
damage the electrical system or
electronic control units or cause a
fire.
If any electrical equipment does not
operate, check for an open fuse.
1. Be sure the ignition switch is pushed to the OFF or LOCK position and theFUSES

GLOVE BOX
WARNING
Keep glove box lid closed while driv-
ing to help prevent injury in an
accident or a sudden stop.
Pull the knob toward you to open the
glove box.
To close the glove box, press the lid
forward until it locks in place.
Use the mechanical key to lock
and
unlock
the glove box. (
“Mechanical
key” page 3-3)
The mechanical key stops when it is
inserted approximately halfway in.
Instruments and controls
2-65

to open the lid.
To close the center console box, press on
the lid until it locks in place.
NOTE:
The console box contains a power out-
let.
CAUTION
Do not leave the console box open.
The open lid may suddenly close
when the vehicle stops.
COAT HOOKSTo use the coat hook, push the upper side
of the hook to release it.

Do not allow children to play with the
seat belts. Most seating positions are
equipped with Automatic Locking
Retractor (ALR) mode seat belts. If
the seat belt becomes wrapped
around a child

position to the
,
,or
to any other
position.
The shift lever cannot be moved out of
the
position and into any other position
with the ignition switch other in the LOCK,
OFF or ACC position.
When accelerating from a stopKeep the foot brake pedal depressed and
push the shift lever button to shift into a
driving gear as following:
Starting and driving
5-21

position.
3. To help prevent the vehicle from roll- ing into the street when parked on a
sloping drive way, it is a good practice
to turn the wheels as illustrated.
.
HEADED DOWNHILL WITH CURB:Turn the wheels into the curb and
move the vehicle forward until the
curb side wheel gently touches the
curb.
.
HEADED UPHILL WITH CURB:Turn the wheels away from the
curb and move the vehicle back
until the curb side wheel gently
touches the curb.
.
HEADED UPHILL OR DOWNHILL, NO
CURB:Turn the wheels toward the side of
the road so the vehicle will move
away from the center of the road if
it moves.
4. Push the ignition switch to the LOCK position.
For models without NCCB (NISSAN Car-
bon Ceramic Brake) package:
The GT-R uses brake pad materials that
have high metallic content. The brake pad
material helps maintain braking perfor-
mance in a wide range of weather and driving conditions.
For the first 3,000 - 6,000 miles (5,000 -
10,000 km) of the vehicle’s service life, and
for the first 3,000 - 6,000 miles (5,000 -
10,000 km) after a brake replacement, the
brake pad to brake rotor clearance is very
small. When parking, apply the parking
brake and move the shift lever to the
position. Idle the engine for more than 20
seconds without depressing the brake
pedal. This allows the brake pads to move
away from the rotor so the pad does not
contact the rotor.
Additionally, the brakes must be dry
before parking the vehicle after driving
on wet roads or after washing the vehicle.
If the roads are wet, lightly apply the
brakes for a short distance before parking
the vehicle to dry the brakes. After wash-
ing the vehicle, dry the brakes by driving
on a dry road for a few miles and apply
the brakes normally based on traffic and
road conditions.
The metallic brake pads and brake disc
rotor may rust together when the brakes
are not applied:
.
If the vehicle is not idled for 20
seconds without the brakes applied,
or if the brakes are applied when the
vehicle is shut off, the rotor and pads
can rust together, even when the brake pads are dry.
. If the brakes are wet when the vehicle
is parked and the parking brake is
applied for a long time.
It is recommended you contact a GT-R
certified NISSAN dealer if the brake pads
and brake rotor have rusted together.
For models with NCCB (NISSAN Carbon
Ceramic Brake) package:
(
“NCCB (NISSAN Carbon Ceramic
Brake)” page 8-20)
Starting and driving
5-47

WARNING
Using the systemDepress the brake pedal and hold it down.
Depress the brake pedal with firm steady
pressure, but do not pump the brakes.
The ABS will operate to prevent the
wheels from locking up. Steer the vehicle
to avoid obstacles.

position.NOTE:
.
If the steering lock release malfunc-
tion indicator appears on the vehicle
information display when the igni-
tion switch is pressed, press the
ignition switch again while gently
turning the steering wheel left and
right. (
“Steering lock release
malfunction indicator” page 2-47)
. If the shiftwarning appears on the
vehicle information display when
the ignition switch is pushed, the
shift lever is in any position except
the
position. Move the shift lever
to the
position. (
“Shift “P”
warning” page 2-46)
. If the Intelligent Key battery dis-
charge indicator appears on the
vehicle information display, the In-
telligent Key battery is discharged
and the ignition switch will not
operate. Insert the Intelligent Key
into the key port to operate the
ignition switch. (
“Intelligent Key
battery discharge indicator” page 2-
48)
. When all of the following conditions
are met for 60 minutes, the battery
saver system will cut off the power
supply to prevent battery discharge.
—The ignition switch is in the ACC
Starting and driving
5-11