bluetooth NISSAN LATIO 2007 Service Owner's Manual

TELEPHONE
AV-65
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: June 20062007 Versa
BLUETOOTH MICROPHONE
Removal
1. Remove over-head console assembly, roof finisher. Refer to EI-39, "HEADLINING" .
2. Remove the Bluetooth microphone.
Installation
Installation is in the reverse order of removal.

LT-108
ILLUMINATION
Revision: June 20062007 Versa
ILLUMINATIONPFP:27545
System DescriptionEKS00HZU
The control of the illumination lamps operation is dependent upon the position of the lighting switch. When the
lighting switch is placed in the 1ST or 2ND position, the BCM (body control module) receives input signal
requesting the illumination lamps to illuminate. This input signal is communicated to IPDM E/R (intelligent
power distribution module engine room) across CAN communication lines. CPU (central processing unit)
located in the IPDM E/R controls the tail lamp relay coil. This relay, when energized, directs power to the illu-
mination lamps, which then illuminate.
Power is supplied at all times

to ignition relay, located in IPDM E/R,

to tail lamp relay, located in IPDM E/R,

through 15A fuse (No. 52, located in IPDM E/R) and

through 20A fuse (No. 53, located in IPDM E/R)

to CPU located in IPDM E/R,

through 40A fusible link (letter g , located in fuse and fusible link box)

to BCM terminal 70, and

through 10A fuse [No. 8, located in fuse block (J/B)]

to BCM terminal 57.
With the ignition switch in the ON or START position, power is supplied

to ignition relay, located in IPDM E/R, and

through 10A fuse [No. 6, located in fuse block (J/B)]

to BCM terminal 38.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 20, located in fuse block (J/B)]

to BCM terminal 11.
Ground is supplied

to BCM terminal 67

through grounds M57 and M61, and

to IPDM E/R terminals 39 and 59

through grounds E15 and E24.
ILLUMINATION OPERATION BY LIGHTING SWITCH
With the lighting switch in the 1ST or 2ND position, BCM receives input signal requesting the illumination
lamps to illuminate. This input signal is communicated to IPDM E/R across CAN communication lines. CPU
located in the IPDM E/R controls the tail lamp relay coil, which, when energized, directs power

through 10A fuse (No. 37, located in IPDM E/R)

through IPDM E/R terminal 29

to microphone terminal 3 (with Bluetooth)

to illumination control switch terminal 1

to glove box lamp terminal 1 (with glovebox lamp)

to audio unit terminal 9

to front air control terminal 5

to A/T device terminal 3 (without M/T)

to hazard switch terminal 3

to combination meter terminal 12

to door mirror remote control switch terminal 16, and

to main power window and door lock/unlock switch terminal 4.
Ground is supplied

to microphone terminal 2 (with Bluetooth)

to glove box lamp terminal 2 (with glove box lamp), and

PG-52
HARNESS
Revision: June 20062007 Versa
D3 B100 GR/5 : Fuel level sensor unit and fuel pump
G5 B101 W/16 : To M12
G5 B102 W/24 : To M13
F3 B103 B/2 : Console power socket
A4 B104 GR/3: EVAP control system pressure sen-
sor
A3 B105 B/2 : EVAP canister vent control valve
G5 B106 W/4 : To M11
A2 B107 BR/6 : Rear combination lamp RH
E4 B108 W/3 : Front door switch RH
F4 B109 Y/2 : Front RH side air bag module
F4 B110 W/10 : To B300
E5 B111 Y/2 : RH side air bag (satellite) sensor
F4 B112 W/3 : Seat belt buckle switch RH
F3 B113 Y/12 : Air bag diagnosis sensor unit
E4 B114 — : Body ground
E4 B115 Y/2 : Front RH seat belt pre-tensioner
C3 B116 W/1 : Rear door switch RH
E3 B117 — : Body ground
B2 B118 Y/2 : RH side curtain air bag module
D3 B119 W/8 : To D301
G5 B120 W/24 : To M14
A3 B121 W/32 : Bluetooth control unit
A3 B122 GR/1 : Bluetooth control unit
D2 B123 B/2 : Rear wheel sensor LH
C3 B124 B/2 : Rear wheel sensor RH
F3 B125 GR/2 : Front console antenna
C3 B126 GR/2 : Rear floor antenna
A2 B132 — : Body ground
B2 B133 W/2 : To D400
A2 B134 W/12 : To D401
E5 B138 B/3 : Belt tension sensor