transmission NISSAN LATIO 2007 Service Repair Manual

-1
QUICK REFERENCE INDEX
AGENERAL INFORMATIONGIGeneral Information
BENGINEEMEngine Mechanical
LUEngine Lubrication System
COEngine Cooling System
ECEngine Control System
FLFuel System
EXExhaust System
ACCAccelerator Control System
CTRANSMISSION/
TRANSAXLECLClutch System
MTManual Transaxle
ATAutomatic Transaxle
CVTCVT
DDRIVELINE/AXLEFAXFront Axle
RAXRear Axle
ESUSPENSIONFSUFront Suspension
RSURear Suspension
WTRoad Wheels & Tires
FBRAKESBRBrake System
PBParking Brake System
BRCBrake Control System
GSTEERINGPSPower Steering System
STCSteering Control System
HRESTRAINTSSBSeat Belts
SRSSupplemental Restraint System (SRS)
IBODYBLBody, Lock & Security System
GWGlasses, Window System & Mirrors
RFRoof
EIExterior & Interior
IPInstrument Panel
SESeat
JAIR CONDITIONERMTCManual Air Conditioner
KELECTRICALSCStarting & Charging System
LTLighting System
DIDriver Information System
WWWiper, Washer & Horn
BCSBody Control System
LANLAN System
AVAudio Visual, Navigation & Telephone System
ACSAuto Cruise Control System
PGPower Supply, Ground & Circuit Elements
LMAINTENANCEMAMaintenance
MINDEXIDXAlphabetical Index
Edition: June 2006
Revision: June 2006
Publication No. SM7E-1C11U0
B
D
© 2006 NISSAN NORTH AMERICA, INC.
All rights reserved. No part of this Service Manual may be reproduced or stored in a retrieval system, or transmitted in any
form, or by any means, electronic, mechanical, photo-copying, recording or otherwise, without the prior written permission
of Nissan North America Inc.
A
C
E
F
G
H
I
J
K
L
M

AT-1
AUTOMATIC TRANSAXLE
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION AT
A
B
AT
Revision: June 20062007 Versa INDEX FOR DTC ........................................................ 5
Alphabetical Index .................................................... 5
DTC No. Index ......................................................... 6
PRECAUTIONS .......................................................... 7
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 7
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 7
Precautions for On Board Diagnostic (OBD) System
of A/T and Engine .................................................... 8
Precautions .............................................................. 8
Service Notice or Precautions .................................. 9
PREPARATION ..........................................................11
Special Service Tools ..............................................11
Commercial Service Tools ...................................... 14
A/T FLUID ................................................................. 16
Checking A/T Fluid ................................................. 16
Changing A/T Fluid ................................................ 17
A/T Fluid Cooler Cleaning ...................................... 17
A/T CONTROL SYSTEM .......................................... 20
Cross-Sectional View ............................................. 20
Shift Mechanism ..................................................... 21
TCM Function ......................................................... 30
CAN Communication .............................................. 31
Input/Output Signal of TCM .................................... 31
Line Pressure Control ............................................ 32
Shift Control ........................................................... 33
Lock-up Control ...................................................... 34
Engine Brake Control (Overrun Clutch Control) ..... 35
Control Valve .......................................................... 37
Centrifugal Cancel Mechanism .............................. 38
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 39
Introduction ............................................................ 39
OBD-II Function for A/T System ............................. 39
One or Two Trip Detection Logic of OBD-II ............ 39
OBD-II Diagnostic Trouble Code (DTC) ................. 39
Malfunction Indicator Lamp (MIL) ........................... 42
TROUBLE DIAGNOSIS ............................................ 43
DTC Inspection Priority Chart ................................ 43Fail-safe .................................................................. 43
How to Perform Trouble Diagnoses for Quick and
Accurate Repair ...................................................... 45
A/T Electrical Parts Location .................................. 50
Circuit Diagram ....................................................... 52
Inspections Before Trouble Diagnosis .................... 53
Road Test ............................................................... 58
Check Before Engine is Started .............................. 58
Check at Idle ........................................................... 59
Cruise Test — Part 1 .............................................. 61
Cruise Test — Part 2 .............................................. 64
Cruise Test — Part 3 .............................................. 65
Vehicle Speed at Which Gear Shifting Occurs ....... 67
Vehicle Speed at Which Lock-up Occurs/Releases ... 67
Symptom Chart ....................................................... 68
TCM Terminals and Reference Value ..................... 78
CONSULT-II Function (A/T) .................................... 80
Diagnostic Procedure Without CONSULT-II ........... 90
DTC U1000 CAN COMMUNICATION LINE .............. 94
Description .............................................................. 94
On Board Diagnosis Logic ...................................... 94
Possible Cause ....................................................... 94
DTC Confirmation Procedure ................................. 94
Wiring Diagram — AT — CAN ................................ 95
Diagnostic Procedure ............................................. 96
DTC P0705 PARK/NEUTRAL POSITION (PNP)
SWITCH .................................................................... 97
Description .............................................................. 97
CONSULT-II Reference Value ................................ 97
On Board Diagnosis Logic ...................................... 97
Possible Cause ....................................................... 97
DTC Confirmation Procedure ................................. 97
Wiring Diagram — AT — PNP/SW ......................... 98
Diagnostic Procedure ............................................. 99
Component Inspection ..........................................101
DTC P0710 A/T FLUID TEMPERATURE SENSOR
CIRCUIT ..................................................................102
Description ............................................................102
CONSULT-II Reference Value ..............................102
On Board Diagnosis Logic ....................................102

AT-3
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa Diagnostic Procedure ........................................... 172
Component Inspection ......................................... 175
DTC TURBINE REVOLUTION SENSOR ............... 176
Description ........................................................... 176
CONSULT-II Reference Value .............................. 176
On Board Diagnosis Logic ................................... 176
Possible Cause .................................................... 176
DTC Confirmation Procedure ............................... 176
Wiring Diagram — AT — PT/SEN ........................ 177
Diagnostic Procedure ........................................... 178
CONTROL UNIT (RAM), CONTROL UNIT (ROM) . 182
Description ........................................................... 182
On Board Diagnosis Logic ................................... 182
Possible Cause .................................................... 182
DTC Confirmation Procedure ............................... 182
Diagnostic Procedure ........................................... 182
MAIN POWER SUPPLY AND GROUND CIRCUIT . 183
Wiring Diagram — AT — MAIN ............................ 183
Diagnostic Procedure ........................................... 184
PNP, OD SWITCH AND CLOSED THROTTLE,
WIDE OPEN THROTTLE POSITION SIGNAL CIR-
CUIT ........................................................................ 186
CONSULT-II Reference Value .............................. 186
TCM Terminals and Reference Value ................... 186
Diagnostic Procedure ........................................... 187
Component Inspection ......................................... 191
SHIFT POSITION INDICATOR CIRCUIT ............... 192
Description ........................................................... 192
CONSULT-II Reference Value .............................. 192
Diagnostic Procedure ........................................... 192
TROUBLE DIAGNOSIS FOR SYMPTOMS ............ 193
Wiring Diagram — AT — NONDTC ...................... 193
OD OFF Indicator Lamp Does Not Come On ...... 198
Engine Cannot Be Started in “P” and “N” Position . 200
In “P” Position, Vehicle Moves Forward or Backward
When Pushed ....................................................... 201
In “N” Position, Vehicle Moves ............................. 201
Large Shock “N” → “R” Position ........................... 202
Vehicle Does Not Creep Backward in “R” Position . 203
Vehicle Does Not Creep Forward in “D”, “2” or “1”
Position ................................................................ 205
Vehicle Cannot Be Started from D
1 ...................... 206
A/T Does Not Shift: D
1 → D2 or Does Not Kickdown:
D
4 → D2 ............................................................... 208
A/T Does Not Shift: D
2 → D3 ............................... 210
A/T Does Not Shift: D
3 → D4 ............................... 212
A/T Does Not Perform Lock-up ............................ 214
A/T Does Not Hold Lock-up Condition ................. 215
Lock-up Is Not Released ...................................... 216
Engine Speed Does Not Return to Idle (Light Brak-
ing D
4 → D3 ) ....................................................... 217
A/T Does Not Shift: D
4 → D3 , When OD OFF .... 218
A/T Does Not Shift: D
3 → 22 , When Selector Lever
“D” → “2” Position ................................................ 219
A/T Does Not Shift: 2
2 → 11 , When Selector Lever
“2” → “1” Position ................................................. 221
Vehicle Does Not Decelerate by Engine Brake .... 223
TCM Self-diagnosis Does Not Activate ................ 227TRANSMISSION CONTROL MODULE ..................228
Removal and Installation ......................................228
SHIFT CONTROL SYSTEM ....................................229
Control Device Removal and Installation ..............229
Control Device Disassembly and Assembly .........232
Selector Lever Knob Removal and Installation .....233
Adjustment of A/T Position ...................................233
Checking of A/T Position ......................................234
A/T SHIFT LOCK SYSTEM ....................................235
Description ............................................................235
Shift Lock System Parts Location .........................235
Wiring Diagram — AT — SHIFT ...........................236
Diagnostic Procedure ...........................................237
KEY INTERLOCK CABLE ......................................239
Removal and Installation ......................................239
ON-VEHICLE SERVICE ..........................................242
Control Valve Assembly and Accumulators ..........242
Park/Neutral Position (PNP) Switch .....................246
Revolution Sensor ................................................247
Turbine Revolution Sensor (Power Train Revolution
Sensor) .................................................................248
Differential Side Oil Seal .......................................250
AIR BREATHER HOSE ..........................................252
Removal and Installation ......................................252
TRANSAXLE ASSEMBLY ......................................253
Removal and Installation ......................................253
OVERHAUL ............................................................257
Components .........................................................257
Oil Channel ...........................................................265
Locations of Adjusting Shims, Needle Bearings and
Thrust Washers ....................................................266
Locations of Snap Rings .......................................267
DISASSEMBLY .......................................................268
Disassembly .........................................................268
REPAIR FOR COMPONENT PARTS .....................285
Manual Shaft ........................................................285
Oil Pump ...............................................................289
Control Valve Assembly ........................................293
Control Valve Upper Body ....................................302
Control Valve Lower Body ....................................306
Reverse Clutch .....................................................309
High Clutch ...........................................................314
Forward and Overrun Clutches ............................320
Low & Reverse Brake ...........................................327
Rear Internal Gear and Forward Clutch Hub ........332
Output Shaft, Output Gear, Idler Gear, Reduction
Pinion Gear and Bearing Retainer ........................336
Band Servo Piston Assembly ...............................343
Final Drive ............................................................349
ASSEMBLY .............................................................354
Assembly (1) .........................................................354
Adjustment (1) ......................................................355
Assembly (2) .........................................................361
Adjustment (2) ......................................................366
Assembly (3) .........................................................369
SERVICE DATA AND SPECIFICATIONS (SDS) ....378
General Specifications ..........................................378
Vehicle Speed at Which Gear Shifting Occurs .....378
Vehicle Speed at When Lock-up Occurs/Releases .378

A/T FLUID
AT-17
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
Changing A/T FluidUCS005M9
1. Warm up A/T fluid.
2. Stop engine.
3. Drain A/T fluid by removing the drain plug. Reinstall the drain plug to the specified torque.
CAUTION:
Do not reuse drain plug gasket.
4. Refill the transaxle with new specified A/T fluid through the A/T fluid charging pipe. Always refill the tran-
saxle with the same volume of A/T fluid that was drained out.
5. Run engine at idle speed for 5 minutes.
6. Check A/T fluid level and condition. Refer to AT- 1 6 , "
Checking A/T Fluid" .
A/T Fluid Cooler CleaningUCS006KH
Whenever the A/T is repaired, overhauled, or replaced, the A/T fluid cooler mounted in the radiator must be
inspected and cleaned.
Metal debris and friction material, if present, can become trapped in the A/T fluid cooler. This debris can con-
taminate the newly serviced A/T or, in severe cases, can block or restrict the flow of A/T fluid. In either case,
malfunction of the newly serviced A/T may result.
Debris, if present, may build up as A/T fluid enters the cooler inlet. It will be necessary to back flush the cooler
through the cooler outlet in order to flush out any built up debris.
A/T FLUID COOLER CLEANING PROCEDURE
1. Identify the A/T inlet and outlet fluid cooler hoses.
2. Position an oil pan under the A/T inlet and outlet fluid cooler
hoses.
3. Disconnect the A/T fluid cooler inlet and outlet rubber hoses
from the steel cooler tubes or bypass valve.
NOTE:
Replace the cooler hoses if rubber material from the hose
remains on the tube fitting.
4. Allow any A/T fluid that remains in the cooler hoses to drain into
the oil pan.
5. Insert the extension adapter hose of a can of Transmission
Cooler Cleaner (Nissan P/N 999MP-AM006) into the cooler out-
let hose.
CAUTION:

Wear safety glasses and rubber gloves when spraying
the Transmission Cooler Cleaner.

Spray Transmission Cooler Cleaner only with adequate
ventilation.

Avoid contact with eyes and skin.

Do not breath vapors or spray mist.
6. Hold the hose and can as high as possible and spray Transmis-
sion Cooler Cleaner in a continuous stream into the cooler outlet hose until A/T fluid flows out of the cooler
inlet hose for 5 seconds. Drain plug: Refer to AT- 2 5 7 , "
Components" .
Fluid grade and capacity: Refer to MA-11, "
RECOMMENDED FLUIDS AND LUBRICANTS" .
SCIA5628E
SCIA5629E

AT-18
A/T FLUID
Revision: June 20062007 Versa
7. Insert the tip of an air gun into the end of the cooler outlet hose.
8. Wrap a shop rag around the air gun tip and end of cooler outlet
hose.
9. Blow compressed air regulated to 5 - 9 kg/cm
2 (70 - 130 psi) through the cooler outlet hose for 10 sec-
onds to force out any remaining A/T fluid.
10. Repeat steps 5 through 9 three additional times.
11. Position an oil pan under the banjo bolts that connect the A/T fluid cooler steel lines to the A/T.
12. Remove the banjo bolts.
13. Flush each steel line from the cooler side back toward the A/T by spraying Transmission Cooler Cleaner
in a continuous stream for 5 seconds.
14. Blow compressed air regulated to 5 - 9 kg/cm
2 (70 - 130 psi) through each steel line from the cooler side
back toward the A/T for 10 seconds to force out any remaining A/T fluid.
15. Ensure all debris is removed from the steel cooler lines.
16. Ensure all debris is removed from the banjo bolts and fittings.
17. Perform AT-18, "
A/T FLUID COOLER DIAGNOSIS PROCEDURE" .
A/T FLUID COOLER DIAGNOSIS PROCEDURE
NOTE:
Insufficient cleaning of the cooler inlet hose exterior may lead to inaccurate debris identification.
1. Position an oil pan under the A/T inlet and outlet cooler hoses.
2. Clean the exterior and tip of the cooler inlet hose.
3. Insert the extension adapter hose of a can of Transmission
Cooler Cleaner (Nissan P/N 999MP-AM006) into the cooler out-
let hose.
CAUTION:

Wear safety glasses and rubber gloves when spraying
the Transmission Cooler Cleaner.

Spray Transmission Cooler Cleaner only with adequate
ventilation.

Avoid contact with eyes and skin.

Do not breath vapors or spray mist.
4. Hold the hose and can as high as possible and spray Transmis-
sion Cooler Cleaner in a continuous stream into the cooler outlet hose until A/T fluid flows out of the cooler
inlet hose for 5 seconds.
5. Tie a common white, basket-type coffee filter to the end of the
cooler inlet hose.
SCIA5630E
SCIA5629E
SCIA5631E

AT-22
A/T CONTROL SYSTEM
Revision: June 20062007 Versa
CLUTCH AND BAND CHART

*1: Operates when OD OFF. (OD OFF indicator lamp is on.)

*2: Oil pressure is applied to both 2nd “apply” side and 3rd “release” side of band servo piston. However, brake band does not con-
tract because oil pressure area on the “release” side is greater than that on the “apply” side.

*3: Oil pressure is applied to 4th “apply” side on condition *2 above, and brake band contracts.

*4: A/T will not shift to 4th when OD OFF. (OD OFF indicator lamp is on.)

: Operates.

A: Operates when throttle opening is less than specification**, activating engine brake.

B: Operates during “progressive” acceleration.

C: Operates but does not affect power transmission.

D: Operates when throttle opening is less than specification**, but does not affect engine brake.
–**: Overrun clutch remains in engaged condition when throttle opening is less than 1/16. Shift posi-
tionR/C
5H/C
6F/C
15O/C
17Band servo
F/O.C
16L/O.C
18L&R/B
19Lock-
upRemarks
2nd
apply3rd
release4th
apply
PPA R K
POSITION
RREVERSE
POSITION
NNEUTRAL
POSITION
D*4 1st *1D B B
2nd *1A BAutomatic
shift
3rd *1A *2C C B
*11 ⇔ 2 ⇔ 3
⇔ 4
4th C *3C C
21stBB
Automatic
shift
1 ⇔ 2 ⇐ 3 2ndB
3rd *2C C B
11stBB
Locks (held
stationary)
in 1st speed
1 ⇐ 2 ⇐ 3 2ndB
3rd *2C C B

A/T CONTROL SYSTEM
AT-23
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
POWER TRANSMISSION
“N” and “P” Positions

“N” position
Power from the input shaft is not transmitted to the output shaft because the clutches do not operate.

“P” position
Similar to the “N” position, the clutches do not operate. The parking pawl engages with the parking gear to
mechanically hold the output shaft so that the power train is locked.
SAT9 9 1I

AT-28
A/T CONTROL SYSTEM
Revision: June 20062007 Versa
“D4 ” (OD) Position

High clutch

Brake band

Forward clutch (Does not affect power
transmission)Input power is transmitted to front carrier through high clutch.
This front carrier turns around the sun gear which is fixed by brake band and makes
front internal gear (output) turn faster.
Engine brakeAt D
4 position, there is no one-way clutch in the power transaxle line and engine
brake can be obtained when decelerating.
SAT3 8 0J

A/T CONTROL SYSTEM
AT-31
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
CAN CommunicationUCS005M D
SYSTEM DESCRIPTION
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only. For details, refer to LAN-47,
"CAN System Specification Chart" .
Input/Output Signal of TCMUCS005M E
*1: Spare for vehicle speed sensor·A/T (revolution sensor)
*2: Spare for accelerator pedal position signal
*3: If these input and output signals are different, the TCM triggers the fail-safe function.
*4: Used as a condition for starting self-diagnostics; if self-diagnosis are not started, it is judged that there is some kind of error.
*5: Input by CAN communications.
*6: Output by CAN communications.Control itemLine
pressure
controlVehicle
speed
controlShift
controlLock-up
controlEngine
brake
controlFail-safe
functionSelf-diag-
nostics
function
InputAccelerator pedal position signal
(*5)XXXXX(*3) XX
Vehicle speed sensor·A/T
(Revolution sensor)XXXXX(*3) XX
Vehicle speed sensor·MTR (*1) X (*1) X (*1) X (*1) X X
Closed throttle position signal
(*5)(*2) X(*2) XXX(*4) X
Wide open throttle position signal
(*5)(*2) X (*2) X (*4) X
Turbine revolution sensor (Power
train revolution sensor)XX X XX
Engine speed signal X X X X
PNP switch X X X X X (*3) X (*4) X
Stop lamp switch signal
(*5)XX (*4) X
A/T fluid temperature sensors
(*5)XXXX XX
Overdrive control switch signal
(*5)XXXX (*4) X
TCM power supply voltage signal X X X X
Out-
putShift solenoid valve A/B X (*3) X X
Line pressure solenoid X (*3) X X
Torque converter clutch solenoid
valveX(*3) XX
Overrun clutch solenoid valve X X (*3) X X
OD OFF indicator lamp
(*6)XX

AT-34
A/T CONTROL SYSTEM
Revision: June 20062007 Versa
CONTROL OF SHIFT VALVES A AND B
Pilot pressure generated by the operation of shift solenoid valves A and B is applied to the end face of shift
valves A and B.
The figure above shows the operation of shift valve B. When the shift solenoid valve is “ON”, pilot pressure
applied to the end face of the shift valve overcomes spring force, moving the valve upward.
Lock-up ControlUCS005MH
The torque converter clutch piston in the torque converter is locked to eliminate torque converter slip and to
increase power transmission efficiency. The solenoid valve is controlled by an ON-OFF duty signal sent from
the TCM. The signal is converted to an oil pressure signal which controls the torque converter clutch piston.
CONDITIONS FOR LOCK-UP OPERATION
When vehicle is driven in 3rd and 4th gear positions, vehicle speed and throttle opening are detected. If the
detected values fall within the lock-up zone memorized in the TCM, lock-up is performed.
TORQUE CONVERTER CLUTCH SOLENOID VALVE CONTROL
Lock-up Control System Diagram
SAT0 0 9J
OD ON OFF
Selector lever “D” position
Gear position D
4D3
Vehicle speed sensor More than set value
Accelerator pedal position signal Less than set opening
Closed throttle position signal OFF
A/T fluid temperature sensor More than 40°C (104°F)
SCIA5623E