open hood NISSAN LEAF 2014 1.G Owners Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2014, Model line: LEAF, Model: NISSAN LEAF 2014 1.GPages: 397, PDF Size: 9.45 MB
Page 61 of 397
NOTE:
•To stop charging mid-charge, remove the
charge connector. Charging automatically
stops.
HOW TO TRICKLE CHARGE (IF SO
EQUIPPED)
WARNING
• If you use any medical electric devices,
such as an implantable cardiac pace-
maker or an implantable cardiovascu-
lar defibrillator, check with the electric
medical device manufacturer concern-
ing the effects that charging may have
on implanted devices before starting
the charge operation. Charging may
affect the operation.
• If you have an implantable cardiac
pacemaker or an implantable cardio-
vascular defibrillator, while the Li-ion
battery is charging:
– Do not stay inside the vehicle.
– Do not go inside the vehicle, for ex-
ample to remove or place an item in
the passenger compartment.– Do not open the rear hatch, for ex-
ample to remove or place an item in
the cargo area.
Charging may affect the operation of
electric medical device and result in
serious personal injury or death.
• In order to avoid an electric shock or
fire due to a short circuit, connect to
GFI (Ground Fault Interrupter) circuit
breaker and use a waterproof electri-
cal ground socket.
• The NISSAN Genuine EVSE (Electric
Vehicle Supply Equipment) charging
device provided with your vehicle
draws 12amps continuously while
charging the Li-ion battery. Do not plug
in to any electrical circuit unless it is
inspected by a licensed electrician to
confirm that the electrical circuit can
accept a 12 amp draw. Any electrical
circuit has a much higher likelihood of
being compromised in the following
conditions listed below.
– Improper use of the charger may
result in a fire and serious injury or
death.
– Do not use this charger in structures
more than 40 years old.– Do not use this charger in structures
using fuse-based circuit protection.
Use only with electrical circuits pro-
tected by circuit breakers.
– Do not use this charger on electrical
circuits with two-prong outlets.
– Do not use charger if outlet appears
damaged or will not hold plug firmly.
– Discontinue charger use immedi-
ately if plug or outlet becomes hot
to the touch or if you notice any
unusual odors.
– Do not use charger if other devices
are plugged into the same circuit.
– Never use extension cords or plug
adapters with charger.
– Do not operate with a damaged
cord.
– Always unplug the charger when not
in use.
– When unplugging, be sure to pull by
the plug and not the cord.
– The device has parts that may spark
inside. Do not use it where gasoline,
paint, or flammable liquids are used
or stored.
– Do not use if a malfunction occurs or
if charger has been damaged in any
manner. Return to a NISSAN certi-
fied LEAF dealer for replacement.
ChargingCH-11
Page 70 of 397
NOTE:
•Depending on the charging station, the
lock mechanism established by local
standards may not be compatible with
your vehicle. It may not be possible for the
charge connector to lock to your vehicle.
•When the power source is cut off while
charging in AUTO mode, the connector
will be continuously locked for 5 minutes,
then it will be released.
•When timer charging is set with AUTO
mode, the connector will not lock until
charging is started.
•In AUTO mode, the charge connector lock
will only lock during normal charging-
.When the following systems are operated
individually or the 12-volt battery is being
charged, the charging connector lock will
not lock:
•Climate Ctrl. Timer
•Remote climate control (if so equipped)
•Li-ion battery warmer
IF THE CHARGE CONNECTOR CAN
NOT BE UNLOCKED
1. Place power switch in the OFF position.
2. Open the hood.
3. Remove the jack rod from the tool set that is
located in the cargo area. See “Tools” in the
“In Case of Emergency” section.
4. Insert the suitable tool into the screw that is
located on the front of hood lock.
5. Turn it clockwise to release the charge con-
nector lock.
6. Remove the charge connector.
CH-20Charging
Page 201 of 397
3 Pre-driving checks and adjustments
Keys...............................3-2
NISSAN Intelligent Keys®...............3-2
Doors..............................3-3
Locking with Mechanical key..............3-4
Locking with inside lock knob..............3-4
Locking with power door lock switch..........3-5
Automatic door locks...................3-5
Child safety rear door lock................3-6
NISSAN Intelligent Key® system..............3-6
NISSAN Intelligent Key® operating range of
the door lock/unlock function..............3-8
Door locks/unlocks precaution.............3-8
NISSAN Intelligent Key® operation..........3-9
12-volt battery saver system..............3-10
Warning signals.....................3-11
Troubleshooting guide.................3-12
How to use remote keyless entry function......3-13Hood.............................3-16
Rear hatch..........................3-17
Secondary rear hatch release.............3-18
Charge port lid........................3-18
Opening charge port lid................3-18
Charge port cap.....................3-19
Tilt steering column.....................3-20
Tilt operation.......................3-20
Sun visors..........................3-20
Vanity mirror.......................3-21
Card holder (driver’s side only)..............3-21
Mirrors............................3-21
Inside rearview mirror..................3-21
Outside mirrors.....................3-23
Page 216 of 397
Switching procedure:
To switch the hazard indicator and horn (chime)
operation, push the LOCK
1and UN-
LOCK
2buttons on the Intelligent Key
simultaneously for more than 2 seconds.
• When the hazard indicator mode is set, the
hazard indicator flashes 3 times.
• When the hazard indicator and horn mode is
set, the hazard indicator flashes once and the
horn chirps once.
WARNING
• Make sure that the hood is completely
closed and latched before driving. Fail-
ure to do so could cause the hood to
open during driving and result in an
accident.
• If steam or smoke is emitting from the
motor compartment, do not open the
hood. Doing so could cause an injury.
When opening the hood:
1. Securely close the charge port door.2. Pull the hood release handle
1located be-
low the instrument panel. The hood will then
spring up slightly.
3. Locate the lever
2in between the hood and
charge port lid, and push the lever upward
with your fingertips.
4. Raise the hood
3.
5. Remove the support rod
4from the hood
and insert it into the slot
5.
Hold the coated part
Awhen removing or
resetting the support rod. Avoid direct con-
tact with the metal parts because they may
be hot immediately after the EV (Electric
Vehicle) system has been stopped.
HOOD
3-16Pre-driving checks and adjustments
Page 217 of 397
When closing the hood:
1. Return the support rod to its original position.
2. Slowly move the hood down to latch the lock.
3. Push the hood down to lock the hood se-
curely into place.
WARNING
• Always make sure that the rear hatch
has been closed securely to prevent it
from opening while driving.
• Do not drive with the rear hatch open.
• Make sure that all passengers have
their hands, etc. inside the vehicle be-
fore closing the rear hatch.
To open the rear hatch, unlock it and push the
rear hatch opener switch
A. Pull up the rear
hatch to open.The rear hatch can be unlocked by:
• Pushing the rear hatch request switch (See
“Intelligent Key system” earlier in this section) .
• Pushing the UNLOCK
button on the
Intelligent Key (See “Intelligent Key system” ear-
lier in this section) .
• Pushing the UNLOCK
button on the
remote controller (See “Intelligent Key system”
earlier in this section) .
• Pushing the power door lock switch to the
“UNLOCK” position.
REAR HATCH
Pre-driving checks and adjustments3-17
Page 326 of 397
In order to maintain the appearance of your ve-
hicle, it is important to take proper care of it.
To protect the paint surfaces, wash your vehicle
as soon as you can:
• after a rainfall to prevent possible damage from
acid rain
• after driving on coastal roads
• when contaminants such as soot, bird drop-
pings, tree sap, metal particles or bugs get on
the paint surface
• when dust or mud builds up on the surface
Whenever possible, store or park your vehicle
inside a garage or in a covered area.
When it is necessary to park outside, park in a
shady area or protect the vehicle with a body
cover.
Be careful not to scratch the paint surface
when putting on or removing the body
cover.
WASHING
Wash dirt off the vehicle with a wet sponge and
plenty of water. Clean the vehicle thoroughly
using a mild soap, a special vehicle soap or
general purpose dishwashing liquid mixed with
clean, lukewarm (never hot) water.
CAUTION
• Do not use car washes that use acid in
the detergent. Some car washes, espe-
cially brushless ones, use some acid
for cleaning. The acid may react with
some plastic vehicle components,
causing them to crack. This could af-
fect their appearance, and also could
cause them not to function properly.
Always check with your car wash to
confirm that acid is not used.
• Do not wash the vehicle with strong
household soap, strong chemical de-
tergents, gasoline or solvents.
• Do not wash the vehicle in direct sun-
light or while the vehicle body is hot, as
the surface may become water-
spotted.
• Avoid using tight-napped or rough
cloths, such as washing mitts. Care
must be taken when removing
caked-on dirt or other foreign sub-
stances so the paint surface is not
scratched or damaged.
Rinse the vehicle thoroughly with plenty of clean
water.
Inside flanges, seams and folds on the doors,
hatches and hood are particularly vulnerable tothe effects of road salt. Therefore, these areas
must be regularly cleaned. Make sure that the
drain holes in the lower edge of the door are
open. Spray water under the body and in the
wheel wells to loosen the dirt and wash away
road salt.
Avoid leaving water spots on the paint surface by
using a damp chamois to dry the vehicle.
WAXING
Regular waxing protects the paint surface and
helps retain new vehicle appearance. Polishing is
recommended to remove built-up wax residue
and to avoid a weathered appearance before
reapplying wax.
A NISSAN certified LEAF dealer can assist you in
choosing the proper product.
• Wax your vehicle only after a thorough washing.
Follow the instructions supplied with the wax.
• Do not use a wax containing any abrasives,
cutting compounds or cleaners that may dam-
age the vehicle finish.
Machine compound or aggressive polishing on a
base coat/clear coat paint finish may dull the
finish or leave swirl marks.
CLEANING EXTERIOR
7-2Appearance and care
Page 334 of 397
Your new NISSAN has been designed to have
minimum maintenance requirements with long
service intervals to save you both time and
money. However, some day-to-day and regular
maintenance is essential to maintain your NIS-
SAN’s fine mechanical condition, as well as its
EV (Electric Vehicle) system performance.
It is the owner’s responsibility to make sure that
the scheduled maintenance, as well as general
maintenance, is performed.
As the vehicle owner, you are the only one who
can ensure that your vehicle receives the proper
maintenance care. You are a vital link in the main-
tenance chain.
SCHEDULED MAINTENANCE
For your convenience, both required and optional
scheduled maintenance items are described and
listed in your “NISSAN Service and Maintenance
Guide”. You must refer to that guide to ensure
that necessary maintenance is performed on your
NISSAN at regular intervals.
GENERAL MAINTENANCE
General maintenance includes those items which
should be checked during normal day-to-day op-
eration. They are essential for proper vehicle op-eration. It is your responsibility to perform these
procedures regularly as prescribed.
Performing general maintenance checks requires
minimal mechanical skill and only a few general
automotive tools.
These checks or inspections can be done by
yourself, a qualified technician or, if you prefer, a
NISSAN certified LEAF dealer.
WHERE TO GO FOR SERVICE
If maintenance service is required or your vehicle
appears to malfunction, have the systems
checked and serviced by a NISSAN certified
LEAF dealer.
NISSAN technicians are well-trained specialists
and are kept up-to-date with the latest service
information through technical bulletins, service
tips, and in-dealership information systems. They
are completely qualified to work on NISSAN ve-
hiclesbeforework begins.
You can be confident that a NISSAN certified
LEAF dealer’s service department performs the
best job to meet the maintenance requirements
on your vehicle — in a reliable and economical
way.During the normal day-to-day operation of the
vehicle, general maintenance should be per-
formed regularly as prescribed in this section. If
you detect any unusual sounds, vibrations or
smell, be sure to check for the cause or have a
NISSAN certified LEAF dealer do it promptly. In
addition, you should notify a NISSAN certified
LEAF dealer if you think that repairs are required.
When performing any checks or maintenance
work, see “Maintenance precautions”.EXPLANATION OF MAINTENANCE
ITEMS
Additional information on the following
items with “*” is found later in this section.
Outside vehicle
The maintenance items listed here should be
performed from time to time, unless otherwise
specified.
Doors and motor hood:Check that all doors
and the motor hood operate properly. Also en-
sure that all latches lock securely. Lubricate
hinges, latches, latch pins, rollers and links if
necessary. Make sure that the secondary latch
keeps the motor hood from opening when the
primary latch is released.
MAINTENANCE REQUIREMENT GENERAL MAINTENANCE
8-2Maintenance and do-it yourself
Page 346 of 397
Pull up the wiper arm manually or using the wiper
rise-up function.
Wiper rise-up function:
To pull up the wiper arm, pull the lever
1within
one minute after the power switch is turned off.
The wiper operation stops in mid-operation and
wiper arm can be pulled up.
To lower the wiper arm, place the wiper arm in the
down position and then push the lever
2up
once after the power switch is turned on.
CAUTION
Do not operate the windshield wiper
while arm is pulled up. The wiper arm or
hood may be damaged.
Replacing
1. Push the release tabA, and move the wiper
blade down the wiper arm
1while pushing
the release tab to remove.
2. Insert the new wiper blade onto the wiper arm
until a click sounds.
3. Rotate the wiper blade so that the dimple is in
the groove.
CAUTION
• After wiper blade replacement, return
the wiper arm to its original position;
otherwise it may be damaged when
the hood is opened.
• Make sure the wiper blades contact
the glass; otherwise the arm may be
damaged from wind pressure.
Type A
8-14Maintenance and do-it yourself
Page 348 of 397
BRAKE PAD WEAR WARNING
The disc brake pads have audible wear warnings.
When a brake pad requires replacement, it will
make a high pitched scraping sound when the
vehicle is in motion. This scraping sound will first
occur only when the brake pedal is depressed.
After more wear of the brake pad, the sound will
always be heard even if the brake pedal is not
depressed. Have the brakes checked as soon as
possible if the wear warning sound is heard.
Under some driving or climate conditions, occa-
sional brake squeak, squeal or other noise may
be heard. Occasional brake noise during light to
moderate stops is normal and does not affect the
function or performance of the brake system.
Proper brake inspection intervals should
be followed.For additional information, see the
maintenance log section of your NISSAN Service
and Maintenance Guide.
MOTOR COMPARTMENT
WARNING
• Never touch, disassemble, remove or
replace the high-voltage parts and
cables, as well as their connectors.
High-voltage cables are colored or-
ange. Touching, disassembling, re-
moving or replacing those parts and
cables can cause severe burns or elec-
tric shock that may result in serious
injury or death.
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
If any electrical equipment does not operate,
check for an open fuse.
1. Confirm that the power switch and the head-
light switch are turned off.
2. Open the hood.
3. Remove the fuse/fusible link holder cover by
pushing the tab
1and lifting the cover from
the right side
2, and then the left side3.
FUSES
8-16Maintenance and do-it yourself
Page 391 of 397
Front passenger air bag and status light....1-42
Front seat, Front seat adjustment........1-3
Fuses.......................8-16
Fusiblelinks ...................8-17
G
Garage door open, HomeLink® Universal . . .2-59
Transceiver..................2-59
Gauge.......................2-5
Driving range..................2-8
ECOindicator ................2-10
Li-ion battery available charge gauge....2-9
Li-ion battery capacity level gauge.....2-10
Li-ion battery temperature gauge.......2-7
Odometer....................2-6
Power meter..................2-7
Speedometer..................2-6
Generalmaintenance...............8-2
Glovebox ....................2-53
H
Hazard warning flasher switch..........6-2
Headlights....................8-22
Bulb replacement...............8-22
Headlightswitch...............2-43Heated seat switch...............2-47
Heated steering wheel switch.........2-46
Highvoltageprecautions............EV-7
HillStart .....................5-25
Hill Start Assist.................5-25
HomeLink® universal transceiver........2-59
Hood release...................3-16
Horn .......................2-47
How to normal charge.............CH-9
How to quick charge.............CH-15
How to trickle charge (if so equipped)....CH-11
I
If the Li-ion battery becomes completely
discharged....................6-11
Immediate charge...............CH-26
Immobilizer system................2-38
In-cabin microfilter................4-15
Indicatorlights..................2-20
Indicators for operation.............2-24
Inside rearview mirror..............3-21
Instrument brightness control..........2-42
Instrument panel..................2-4
Intelligent Key system..............3-13
Remote keyless operation..........3-13
Interior light replacement............8-23
Interior lights...................2-58ISOFIX child restraint..............1-19
J
Jump starting...................6-9
K
Keyless entry...................3-13
With Intelligent Key system (See Intelligent
Key system)..................3-13
Keys ........................3-2
For Intelligent Key system...........3-6
L
Labels ......................1-48
Airbagwarninglabels............1-48
Air conditioner specification label.......9-9
Emission control information label......9-8
F.M.V.S.S./C.M.V.S.S. certification label . . .9-8
Motor serial number..............9-8
Tire and Loading information label . . .8-27, 9-9
Vehicle identification number (VIN)......9-7
LATCH system..................1-19
License plate, Installing front license plate . . .9-9
Light .......................1-48