change time NISSAN MAXIMA 2003 A33 / 5.G Navigation Manual

Thank you for purchasing a NISSAN automo-
bile. This user’s manual is for the navigation
system only .
Please read this manual carefully to ensure safe
operation of the navigation system.

Please read your vehicle’s owner’s manual
first.

Do not remove this manual from the vehicle
when selling this vehicle. The next user of
this navigation system may need the
manual.

Because of possible specification changes,
parts of this manual may not apply to your
vehicle.

All information, specifications and illustra-
tions in this manual are those in effect at the
time of printing. NISSAN reserves the right
to change specifications or design at any
time without notice.

may not be possible.

The following may occur when the route is
being displayed.
— Even if you are requesting calculation from
the main road, the origin of the route may
not exactly match the current vehicle posi-
tion.
— Even if you are requesting calculation to the
destination on the main road, the end of the
route may not exactly match the destination.
— Even if you are requesting calculation from
the main road, the system may show a route
from another main road. This may be be-
cause the icon to show the current vehicle
position (vehicle icon) is not set accurately .
In that case, park the car in a safe place and
reset the vehicle icon, or continue driving
to see if the vehicle icon appears on the
main road before requesting route calcula-
tion again.
— There are cases in which the system showsa detoured route to reach the destination or
waypoints, if you set them from memory or
facility information. In order to correct this,
you will have to be careful about the traffic
direction, especially when the lanes with
different travel directions are shown sepa-
rately . Such places are interchanges and
service areas.
— This system makes no distinction between
limited traffic control and total control
(blockage). It may show a detoured route
even if the road is usable.
— Even if the freeway preference is set to OFF ,
the route may be set on them. T o avoid this,
set a waypoint on another road type and re-
quest calculation.
— Even if the preference is set as OFF for a
ferry line, the route may be set on it. T o
avoid this, set a waypoint on a road and re-
quest calculation.
— Ferry lines, except those which accept onlypedestrians, bicycles and motorcycles, are
stored in this system. When using them,
take into consideration the travel time re-
quired and operational condition to decide
whether to use them or not.
ABOUT THE DISPLAY ERROR
The following cases may affect the display ac-
curacy of the vehicle’s position or travel direc-
tion. The accuracy will return to normal if the
driving conditions return to normal.
— When there is a similar road nearby .
— When the vehicle is traveling on a long
stretch of straight road or series of curves
with a large radius.
— When the vehicle is traveling in an area with
a checkerboard road system.
— When the vehicle is making consecutive S
curves.
— When the vehicle is at a large Y -shaped
junction.
HOW DO I OPERATE THE NISSAN NAVIGATION SYSTEM?
4-15

4. The display shows the direction and dis-
tance from the current vehicle position to
the selected facility .
Select the facility name you want to set as
a destination (waypoint).5. The display shows the [ROUTE PRIORI-
TIES] screen.
Set route priorities, then press the
OK
key . The route calculation to the destination
will be started.
INFO:
If quick stop is set after the destination was set,
the system starts the route calculation to the
location as the waypoint. Five waypoints can be
registered at the same time.Quick Stop Customer Setting
1. For example, set “REST AURANT”.
Change to the current vehicle location screen.
Select the
Setting key .
2. Select the
System Setting key on the
[SETTINGS] screen.
INV0355INV0274INV0259
HOW DO I PROGRAM A DESTINATION?
5-27

SCREEN INFORMA TION —
PLANVIEW DISPLA Y
Direction key:
This indicates and sets the direction of the map
on the display .
Please refer to “Changing the display direc-
tion” on page 11-6.
Map scale:
This display indicates the scale on the current
map.
V ehicle icon:
This icon indicates your vehicle and the direc-
tion of travel.
GPS indicator:
This will tell you the strength of the GPS signal
received.
Please refer to “Accuracy of positioning” on
page 2-2.
:
This will indicate the approximate distance of
route and traveling time to the destination. This
indicator will appear when you set the desti-
nation with the route guidance ON.
:
When the route guidance is OFF or when routecalculation is not started after you set the des-
tination, it will show the direction and approxi-
mate straight distance to the destination.
SCREEN INFORMA TION —
BIRD VIEWTMDISPLA Y
Map scale:
This display indicates the scale on the current
map.
By using the ZM− ZM+ buttons, you can
change the scale of the map.
INV0419
INV0422
HOW DO I ADJUST THE DISPLAY?
11-2

In order to avoid complication of the map,
all road names are not always shown on the
screen. When the display re-draws the map,
a road name which is shown on the pre-
vious screen may not appear on the new
screen.
ZOOMING IN AND OUT OF
THE MAP
Use the ZM− / ZM+ button to change the
scale of the display and height view.
Nine map scales are available from the most
detailed (1 : 10,000) to the widest (1 : 20.48
million).
Each time the ZM+ button is pressed, the
map scale will change one level to display a
more detailed map.
Each time the ZM− button is pressed, the
map scale will change one level to display a
map that shows a wider area.The chosen map scale will be displayed on the
left side of the screen.
INFO:
By pressing the button repeatedly , you can skip
the levels to reach the map of desired scale.
Scale level on the Planview display
Map scale Actual distance
1 : 20.48 million 160 miles
1 : 5.12 million 40 miles
1 : 1.28 million 10 miles
1 : 320,000 2.5 miles
1 : 160,000 1 mile
1 : 80,000 1/2 mile
1 : 40,000 1/4 mile
1 : 20,000 1/8 mile
1 : 10,000 1/16 mile
Scales on the BirdviewTMis listed on page
11-3. Most detailed level (1: 10,000)
The widest level (1: 20.48 million)
INV0425
INV0426
HOW DO I ADJUST THE DISPLAY?
11-5

6. Adjust the direction using theand
key .
The arrow on the display shows the direction
of the vehicle icon.
7. Select the
Set key .INFO:

It is not possible to update the vehicle lo-
cation when the vehicle is moving.

Depending on the driving conditions, the
vehicle icon may not exactly correspond to
the actual location of the vehicle. T o verify
position, refer to map books or check actual
landmarks.

If you notice that the system is displaying
a different road from the one the vehicle is
actually traveling, and the vehicle icon doesnot go back to the right road after traveling
approximately 6-1/4 miles (10 km), update
the vehicle location.
CHANGING THE DISPLA Y
MODE
Y ou can split the screen into two sections to
display the map and A/C setting at the same
time.
1. Change to the current vehicle location
screen.
2. Select the
Setting key .
INV0451INV0452
HOW DO I ADJUST THE DISPLAY?
11-15