driver seat adjustment NISSAN MAXIMA 2017 A36 / 8.G Quick Reference Guide

15
4
CANCEL SWITCH
The trunk lid cancel switch 4 is located in
the glove box.
The trunk lid c annot be opened when the
cancel switch
4 is off.
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating and
feature information.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your
Owner’s Manual.
SEAT ADJUSTMENTS
SEAT FABRIC
If so equipped , your vehicle’s seats may be made from a material known as
Alcantara®. In the case of most localized stains, using lukewarm water and
soap will restore Alcantara® to its factory condition. For more details on proper
cleaning, please refer to your Owner’s Manual.
POWER SEATS
To slide the seat forward or backward, push the
switch 1 forward or backward.
To recline the seatback, push the
switch
2 forward or backward.
POWER SEAT LIFTER (driver’s seat)
To adjust the angle of the front seat cushion or height of the seat, push the front or rear
end of the
switch 1 up or down.
POWER LUMBAR SUPPORT
(if so equipped for driver’s seat)
To adjust the seat lumbar support, push the front or back end of the
switch 3.
THIGH SUPPORT (if so equipped for driver’s seat)
Pull up and hold the lever 4 to extend
the front portion of the seat to the
desired position.
FOLDING DOWN THE REAR SEAT
To fold the rear seatback, press down on the button on the rear parcel shelf
5. The
passenger’s side rear seatback will release.
The pull straps 6 located in the trunk will
release the rear seatbacks to allow them to
fold forward.
123
5
4
6
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.

16
AUTOMATIC DRIVE POSITIONER (if so equipped)
Two positions for the driver’s seat, steering column (if so equipped) and outside mirrors
can be stored in the automatic drive
positioner memory.
Follow this procedure to set the memory positions:



•

Plac
e the ignition switch in the ON or ACC position. (The vehicle should be
stopped while setting the memory.)



•

A
djust the driver’s seat, steering column (if so equipped) and outside mirrors to
the desired positions using the adjusting switches for each feature.



•

Push the
SET switch, and within 5 seconds, push the memory switch (1 or 2).



• The indic
ator light for the memory switch you select will illuminate for
approximately 5 seconds, and a chime will sound when the memory is stored.



• The driv
er’s seat, steering column (if so equipped) and outside mirror positions
are now set to your preferences.
These memoriz ed positions can also be linked to your Nissan Intelligent Key®.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your
Owner’s Manual.
OUTSIDE MIRROR CONTROL SWITCH
To select the right or lef t side mirror, slide the
mirror control switch
1 right or lef t.
To adjust the mirror angle, move the control switch up, down, right or lef t.
To prevent accidentally moving the mirror, slide the mirror control switch
1 to the
center (neutral) position.
REVERSE TILT-DOWN FEATURE (if so equipped)
The reverse tilt-down feature will turn both outside mirror surfaces downward to
provide better rear visibility close to the vehicle.
1.

Apply the brake.
2.

Place the ignition switch in the ON position.
1
FIRST DRIVE FEATURES
To raise the seatback, lif t up each seatback and push it to the upright position until it is latched.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Safety — Seats, seat belts and supplemental restraint system
(section 1)” of your Owner’s Manual.
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.