mirror NISSAN MURANO 2003 1.G User Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2003, Model line: MURANO, Model: NISSAN MURANO 2003 1.GPages: 265, PDF Size: 2.03 MB
Page 90 of 265
LUGGAGEWhen the switch is in the ON position
A, the
light illuminates while the back door is opened.
When the back door is closed, the light will go
off.
When the switch is in the OFF position
B, the
light will turn off.The light on the vanity mirror will turn on when
the cover on the vanity mirror is opened.
When the ceiling light or the map light
switch or rear light switch is in the ON
position, the ceiling, map, rear and vanity
mirror lights will automatically turn off 30
minutes after the ignition switch has been
turned to the OFF position. To turn on the
light again, insert the key into the ignition
switch and move it to the ONposition.The HomeLink
Universal Transceiver provides a
convenient way to consolidate the functions of
up to three individual hand-held transmitters into
one built-in device.
HomeLink
Universal Transceiver:
Will operate most Radio Frequency (RF)
devices such as garage doors, gates, home
and office lighting, entry door locks and se-
curity systems.
Is powered by your vehicle’s battery. No
separate batteries are required. If the vehi-
cle’s battery is discharged or is discon-
nected, HomeLink
will retain all program-
ming.
Once the HomeLinkUniversal Transceiver
is programmed, retain the original trans-
mitter for future programming procedures
(i.e., new vehicle purchases). Upon sale of
the vehicle, the programmed HomeLink
Universal Transceiver buttons should be
erased for security purposes. For addi-
tional information, refer to “Programming
HomeLink
” later in this section.
SIC2131
SIC2064
VANITY MIRROR LIGHT (if so
equipped)HomeLink
UNIVERSAL
TRANSCEIVER (if so equipped)Instruments and controls
2-39
03.1.28/Z50-D/V5.0
Page 98 of 265
3 Pre-driving checks and adjustmentsKeys ........................................................................................... 3-2
Doors......................................................................................... 3-2
Locking with key ............................................................... 3-3
Locking with inside lock knob...................................... 3-3
Locking with power door lock switch ......................... 3-4
Child safety rear door lock ............................................ 3-4
Remote keyless entry system ............................................. 3-4
How to use remote keyless entry system.................. 3-5
Battery replacement ........................................................ 3-7
Hood ......................................................................................... 3-9
Back door ................................................................................ 3-9
Fuel filler lid ........................................................................... 3-11
Open the filler lid ........................................................... 3-11
Fuel filler cap .................................................................. 3-11
Steering wheel ..................................................................... 3-13Tilt operation ................................................................... 3-13
Pedal position adjustment ................................................. 3-13
Sun visors.............................................................................. 3-14
Mirrors .................................................................................... 3-14
Inside mirror .................................................................... 3-14
Automatic anti-glare inside mirror (if so
equipped)......................................................................... 3-15
Outside mirrors .............................................................. 3-15
Automatic drive positioner (if so equipped) ................. 3-16
Automatic drive positioner operation........................ 3-16
Procedure for storing memory ................................... 3-17
03.1.28/Z50-D/V5.0
Page 111 of 265
CAUTION
Do not adjust the pedal position with
your foot on the pedal.
CAUTION
Store the main sun visor after storing
the extension sun visor.
INSIDE MIRRORThe night position will reduce glare from the
headlights of vehicles behind you at night.
WARNING
Use the night position only when neces-
sary, because it reduces rear view clar-
ity.
SPA1583
PD1006M
SUNVISORS MIRRORS
3-14
Pre-driving checks and adjustments
03.1.28/Z50-D/V5.0
Page 112 of 265
AUTOMATIC ANTI-GLARE INSIDE
MIRROR (if so equipped)
WARNING
Use Automatic Anti-glare only when
necessary, because it reduces rear view
clarity.
The inside mirror is designed so that it automati-
cally changes reflection according to the inten-
sity of the headlights of the vehicle following you.
When the inside MIRROR switch is in the ONposition (The Auto indicator light will illuminate),
excessive glare from the headlights of the ve-
hicle behind you will be reduced. When the
switch of the inside mirror is in the OFF position,
the inside mirror will operate normally.
For the HomeLink
Universal Transceiver and
the compass display, see the description in the
“2. Instruments and controls” section.
OUTSIDE MIRRORS
WARNING
Objects viewed in the outside mirror on
the passenger side are closer than they
appear. Be careful when moving to the
right. Using only this mirror could cause
an accident. Use inside mirror or glance
over your shoulder to properly judge
distances to other objects.
The outside mirror will operate only when the
SPA1448
SPA1449A
Pre-driving checks and adjustments
3-15
03.1.28/Z50-D/V5.0
Page 113 of 265
ignition switch is in the ACC or ON position.
Move the switch to right
A
or left
B
to select
the right or left outside mirror, then adjust the
mirror to the desired position by pushing the
button
C.
Foldable outside mirrorsPush the outside mirror backward to fold it.
AUTOMATIC DRIVE POSITIONER
OPERATIONThis system is designed so that the driver’s seat,
outside mirror and pedals (Brake, Accelerator)
will automatically move when the selector lever is
in the P (Park) position. This allows the driver to
get in and out of the driver’s seat more easily.
When one of the following conditions is met, the
driver’s seat will slide backward while the selec-
tor lever is in the P (Park) position:
When the key is removed from the ignition
switch.
When the driver’s door is opened with the
key turned to LOCK.
When the key is turned from ACC to LOCK
with the driver’s door open.
When one of the following conditions is met
while the selector lever is in the P (Park) position,
the driver’s seat will return to the positions
before being set.
When the key is inserted into the ignition
switch.
When the driver’s door is closed with the key
turned to LOCK.
When the key is turned from ACC to ON.
MPA0008
AUTOMATIC DRIVE POSITIONER
(if so equipped)
3-16
Pre-driving checks and adjustments
03.1.28/Z50-D/V5.0
Page 114 of 265
PROCEDURE FOR STORING
MEMORYTwo positions can be stored in the automatic
drive positioner memory.Follow these proce-
dures to use the memory system.
1. Set the selector lever to the P (Park)
position.
2. Turn the ignition ON.
3. Adjust the driver’s seat, outside mirrors and
pedals to the desired positions by manually
operating each adjusting switch. For addi-
tional information, see “Seats” in the “1.
Seats, restraints and supplemental air bag
systems” section and “Pedal position adjust-
ment” earlier in this section.
During this step, do not turn the ignition to
any positions other than ON.
4. Push the SET switch and, within 5 seconds,push the memory switch 1 or 2 fully for at
least 1 second.
The indicator light for the pushed memory
switch will come on and stay on for approxi-
mately 5 seconds after pushing the switch.
After the indicator light goes off, the selected
positions are stored in the selected memory
(1 or 2). Pushing the unlock button on the
keyfobwithin this 5 seconds, will link the
selected memory to the keyfob.
When the link is completed, the indicator light
of the selected memory switch will blink for
approximately 5 seconds.
When you unlock the door with the link
completed keyfob, the driver’s seat will move
back and move to the memorized position.
If memory is stored in the same memory
switch, the previous memory and the memory
which is linked to the keyfob, will be deleted.
Confirming memory storageTurn the ignition ON and push the SET
switch. If the main memory has not been
stored, the indicator light will come on for
approximately 0.5 seconds. When the
memory has stored the position, the indicator
light will stay on for approximately 5 seconds.
If the battery cable is disconnected, or if the
SPA1584
Pre-driving checks and adjustments
3-17
03.1.28/Z50-D/V5.0
Page 115 of 265
fuse blows, the memory will be canceled. In
such a case, reset the desired positions
using the following procedures.
1. Open and close the driver’s door more than
two times with the ignition key in the LOCK
position.
2. Reset the desired position using the previous
procedure.
Selecting the memorized position1. Set the selector lever to the P (Park) position.
2. Turn the ignition ON.
3. Push the memory switch 1 or 2 fully for at
least 1 second.
The driver’s seat, pedals and outside mirror
will move to the memorized position with the
indicator light flashing. Then the light will stay
on for approximately 5 seconds.Cancellation of the systemThe automatic drive positioner system can be
canceled.
See “4. Display screen, heater, air conditioner
and audio systems” section.System operationThe automatic drive positioner system will notwork or will stop operating under the following
conditions:
when the vehicle speed is above 4 MPH (7
km/h).
when either of the memory switches is
pressed while the automatic drive positioner
is operating.
when the adjusting switch for the driver’s
seat, pedal or outside mirror is turned on
while the automatic drive positioner is oper-
ating.
when the memory switch 1 or 2 is not pushed
for at least 1 second.
when the seat, pedal and outside mirror has
already been moved to the memorized posi-
tion.
when no seat position is stored in the
memory switch.3-18
Pre-driving checks and adjustments
03.1.28/Z50-D/V5.0
Page 158 of 265
This position turns on the ignition system and the
electrical accessories.
START (4)
This position activates the starter motor, starting
the engine.NISSAN VEHICLE IMMOBILIZER
SYSTEMThe Nissan Vehicle Immobilizer System will not
allow the engine to start without the use of the
registered Nissan Vehicle Immobilizer System
key.
If the engine fails to start using the registered
Nissan Vehicle Immobilizer System key, it may be
due to interference caused by another Nissan
Vehicle Immobilizer System key, an automated
toll road device or automated payment device on
the key ring. Restart the engine using the follow-
ing procedures:
1. Leave the ignition switch in the ON position
for approximately 5 seconds.
2. Turn the ignition switch to the OFF or LOCK
position and wait approximately 10 seconds.
3. Repeat step 1 and 2 again.
4. Restart the engine while holding the device
(which may have caused the interference)
separate from the registered Nissan VehicleImmobilizer System key.
If this procedure allows the engine to start,
NISSAN recommends placing the registered
Nissan Vehicle Immobilizer System key on a
separate key ring to avoid interference from
other devices.Make sure the area around the vehicle is
clear.
Maintenance items should be checked peri-
odically, for example, each time you check
engine oil.
Check that all windows and lights are clean.
Visually inspect tires for their appearance and
condition. Also, check tires for proper infla-
tion.
Lock all doors.
Position seat and adjust head restraints.
Adjust inside and outside mirrors.
Adjust the pedal position.
Fasten seat belts and ask all passengers to
do likewise.
Check the operation of warning lights when
key is turned to the ON (3) position.
BEFORE STARTING THE ENGINE
Starting and driving
5-9
03.1.28/Z50-D/V5.0
Page 221 of 265
EXTERIOR AND INTERIOR LIGHTS
Item Wattage (W) BulbNo.
Front turn signal* 21 T20
Front park light* 3.8 T10 C-2F
Front side marker light* 3.8 T10 C-2F
Front fog light (if so equipped)* 51 HB4
Rear combination light*
Turn signal 21 T20
Stop/Tail 21/5 T20
Side marker light 5 T10
Back-up* 16 21CP
License plate light* 5 T10
High-mounted stop light* 2.4 LED
Ceiling light 8
Map light 8
Rear personal light* 8
Step light* 2.7 161
Luggage light 8 158
Vanity mirror light (if so equipped) 2 —
*: See a NISSAN dealer for replacement.
Replacement proceduresAll other lights are either type A, B, C or D. When
replacing a bulb, first remove the lens and/or
cover.
MDI0006
8-26
Maintenance and do-it-yourself
03.1.28/Z50-D/V5.0
Page 250 of 265
After the hitch is removed, seal the
bolt holes to prevent exhaust fumes,
water or dust from entering the pas-
senger compartment.
Regularly check all hitch mounting
bolts are securely mounted.
To reduce the possibility of addi-
tional damage if your vehicle is
struck from the rear, where practical,
remove the hitch and/or receiver
when not in use.
Never connect a trailer brake system
directly to the vehicle brake system.Tire pressuresWhen towing a trailer, inflate the vehicle tires
to the recommended cold tire pressure indi-
cated on the tire placard (located on the
driver’s door center pillar).
Trailer tire condition, size, load rating and
proper inflation pressure should be in accor-
dance with the trailer and tire manufacturers’
specifications.
Safety chainAlways use a suitable chain between your ve-
hicle and the trailer. The chain should be
crossed and should be attached to the hitch, not
to the vehicle bumper or axle. Be sure to leave
enough slack in the chain to permit turning
corners.Trailer lightsTrailer lights should comply with federal and/or
local regulations. When wiring the vehicle for
towing, connect the stop and tail light pickup
into the vehicle electrical circuit at a point be-
tween the sensor and stop light or light switch.Trailer brakesIf your trailer is equipped with a braking system,
make sure it conforms to federal and/or local
regulations and that it is properly installed.
WARNING
Never connect a trailer brake system
directly to the vehicle brake system.Pre-towing tipsBe certain your vehicle maintains a levelposition when a loaded and/or unloaded
trailer is hitched. Do not drive the vehicle if it
has an abnormal nose-up or nose-down con-
dition; check for improper tongue load, over-
load, worn suspension or other possible
causes of either condition.
Always secure items in the trailer to prevent
load shifts while driving.
Be certain your rear view mirrors conform to
all federal, state or local regulations. If not,
install any mirrors required for towing before
driving the vehicle.
Trailer towing tipsIn order to gain skill and an understanding of the
vehicle’s behavior, you should practice turning,
stopping and backing up in an area which is free
from traffic. Steering stability, and braking per-
formance will be somewhat different than under
normal driving conditions.
Always secure items in the trailer to prevent
load shift while driving.
Avoid abrupt starts, acceleration or stops.
Avoid sharp turns or lane changes.
Always drive your vehicle at a moderate
speed.
Always block the wheels on both vehicle andTechnical and consumer information
9-19
03.1.28/Z50-D/V5.0