ECU NISSAN MURANO 2007 1.G User Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2007, Model line: MURANO, Model: NISSAN MURANO 2007 1.GPages: 345, PDF Size: 3.57 MB
Page 33 of 345
Storing rear seat belt bucklesBefore folding down the seat, put the buckles in
the storage of the seat cushion to avoid drop-
ping it under the seat cushion.SEAT BELT EXTENDERSIf, because of body size or driving position, it is
not possible to properly fit the lap-shoulder belt
and fasten it, an extender is available. The ex-
tender adds approximately 8 inches (200 mm) of
length and may be used for either the driver or
front passenger seating position. See a NISSAN
dealer for assistance if the extender is required.
WARNING
Only NISSAN seat belt extenders,
made by the same company which
made the original equipment seat
belts, should be used with NISSAN
seat belts.
Adults and children who can use the
standard seat belt should not use an
extender. Such unnecessary use
could result in serious personal in-
jury in the event of an accident.
Never use seat belt extenders to in-
stall child restraints. If the child re-
straint is not secured properly, the
child could be seriously injured in a
collision or a sudden stop.SEAT BELT MAINTENANCETo clean the seat belt webbings,apply a
mild soap solution or any solution recom-
mended for cleaning upholstery or carpets.
Then brush the webbing, wipe it with a cloth
and allow it to dry in the shade. Do not allow
the seat belts to retract until they are com-
pletely dry.If dirt builds up in the shoulder belt guide of
the seat belt anchors, the seat belts may
retract slowly. Wipe the shoulder belt guide
with a clean, dry cloth.
Periodically check to see that the seat
belt and the metal componentssuch as
buckles, tongues, retractors, flexible wires
and anchors work properly. If loose parts,
deterioration, cuts or other damage on the
webbing is found, the entire belt assembly
should be replaced.
SSS0235
1-20
Safety — seats, seat belts and supplemental restraint system
06.7.5/Z50-D/V5.0
Page 35 of 345
Child restraint anchor points are de-
signed to withstand only those loads
imposed by correctly fitted child re-
straints. Under no circumstances are
they to be used for adult seat belts or
harnesses.
Adjustable seatbacks should be po-
sitioned to fit the child restraint, but
as upright as possible.
After attaching the child restraint,
test it before you place the child in it.
Push it from side to side while hold-
ing the seat near the LATCH attach-
ment or by the seat belt path. Try to
tug it forward and check to see if the
belt holds the restraint in place. The
child restraint should not move more
than 1 in (25 mm). If the restraint is
not secure, tighten the belt as neces-
sary, or put the restraint in another
seating position and test it again.
You may need to try a different child
restraint. Not all child restraints fit in
all types of vehicles.
When your child restraint is not in
use, keep it secured with the LATCH
System or a seat belt to prevent it
from being thrown around in case of
a sudden stop or accident.
CAUTION
Remember that a child restraint left in a
closed vehicle can become very hot.
Check the seating surface and buckles
before placing your child in the child
restraint.
This vehicle is equipped with a universal child
restraint lower anchor system, referred to as the
Lower Anchors and Tethers for CHildren System
or LATCH. Some child restraints include two
rigid or webbing-mounted attachments that can
be connected to these lower anchors. For de-
tails, see “Lower Anchors and Tethers for CHil-
dren System (LATCH)” in this section.
If you do not have a LATCH compatible child
restraint, the vehicle seat belts can be used. See
“Child restraint installed using the seat belts”
later in this section. In general, child restraints
are also designed to be installed with the lap
portion of a lap/shoulder seat belt.
Several manufacturers offer child restraints for
infants and small children of various sizes. When
selecting any child restraint, keep the following
points in mind:
Choose only a restraint with a label certifyingthat it complies with Federal Motor Vehicle
Safety Standard 213 or Canadian Motor
Vehicle Safety Standard 213.
Check the child restraint in your vehicle to be
sure it is compatible with the vehicle’s seat
and seat belt system.
If the child restraint is compatible with your
vehicle, place your child in the child restraint
and check the various adjustments to be sure
the child restraint is compatible with your
child. Choose a child restraint that is de-
signed for your child’s height and weight.
Always follow all recommended procedures.
All U.S. states and Canadian provinces or
territories require that infants and small
children be restrained in an approved child
restraint at all times while the vehicle is
being operated.
1-22
Safety — seats, seat belts and supplemental restraint system
06.7.5/Z50-D/V5.0
Page 36 of 345
Lower Anchors and Tethers for
CHildren SYSTEM (LATCH)Your vehicle is equipped with special anchor
points that are used with Lower Anchors and
Tethers for CHildren System (LATCH) compat-
ible child restraints. This system may also be
referred to as the ISOFIX or ISOFIX compatible
system. With this system, you do not have to use
a vehicle seat belt to secure the child restraint.
The LATCH anchor points are provided to install
child restraints in the rear outboard seating
positions only. Do not attempt to install a child
restraint in the center position using the LATCH
anchors.
LATCH lower anchor point locationsThe LATCH anchors are located at the rear of
the seat cushion near the seatback. A label is
attached to the seatback to help you locate the
LATCH anchors.
WARNING
Attach LATCH compatible child re-
straints only at the locations shown
in the illustration. If a child restraint
is not secured properly, your child
could be seriously injured or killed in
an accident.
Do not secure a child restraint in the
center rear seating position using the
LATCH anchors. The child restraint
SSS0419B
LATCH label location
SSS0689
LATCH lower anchor location
Safety — seats, seat belts and supplemental restraint system
1-23
06.7.5/Z50-D/V5.0
Page 37 of 345
will not be secured properly.
Child restraint anchor points are de-
signed to withstand only those loads
imposed by correctly fitted child re-
straints. Under no circumstance are
they to be used for adult seat belts or
harnesses.
Installing child restraint LATCH
anchor attachmentsLATCH compatible child restraints include two
rigid or webbing-mounted attachments that can
be connected to two anchors located at certain
seating positions in your vehicle. With this sys-
tem, you do not have to use a vehicle seat belt to
secure the child restraint. Check your child
restraint for a label stating that it is compatible
with LATCH. This information may also be in the
instructions provided by the child restraint
manufacturer.LATCH child restraints generally require the use
of a top tether strap. See “Top tether strap child
restraint” in this section for installation instruc-
tions.
When installing a child restraint, carefully read
and follow the instructions in this manual and
those supplied with the child restraint. See
“Child restraint installation using LATCH” in this
section.
SSS0643
LATCH webbing-mounted attachment
SSS0644
LATCH rigid attachment
1-24
Safety — seats, seat belts and supplemental restraint system
06.7.5/Z50-D/V5.0
Page 38 of 345
TOP TETHER STRAP CHILD
RESTRAINTIf the manufacturer of your child restraint re-
quires the use of a top tether strap, it must be
secured to an anchor point.
WARNING
Child restraint anchor points are de-
signed to withstand only those loads
imposed by correctly fitted child re-
straints. Under no circumstances arethey to be used for adult seat belts or
harnesses.
The child restraint top tether strap
may be damaged by contact with the
tonneau cover or items in the cargo
area. Remove the tonneau cover from
the vehicle or secure it in the cargo
area. Also secure any items in the
cargo area. Your child could be seri-
ously injured or killed in a collision if
the top tether strap is damaged.
Top tether anchor point locationsAnchor points are located as illustrated.A
: for rear left side seat position
B
: for rear right side seat position
C
: for rear center seat position
Installing top tether strapFirst, secure the child restraint with the seat belt
or LATCH (rear outboard seat positions only), as
applicable.
For the center position
C, remove the anchor
cover from the anchor point as illustrated. Keep
the removed cover in a secure place to prevent
loss or damage.
Remove the head restraint from the seatback.
Store it in a secure place. Position the top tether
strap over the top of the seatback and secure it
to the tether anchor bracket that provides the
straightest installation. Tighten the strap accord-
ing to the manufacturer’s instructions to remove
any slack.
If you have any questions when installing a
top tether strap child restraint on the rear
seat, consult your NISSAN dealer for de-
tails.
SSS0234
SSS0393
Safety — seats, seat belts and supplemental restraint system
1-25
06.7.5/Z50-D/V5.0
Page 39 of 345
CHILD RESTRAINT INSTALLATION
USING LATCH
WARNING
Attach LATCH compatible child re-
straints only at the locations shown.
For the LATCH lower anchor loca-
tions, see “Lower Anchors and Teth-
ers for CHildren System (LATCH)” in
this section. If a child restraint is not
secured properly, your child could be
seriously injured or killed in an acci-
dent.
The LATCH anchors are designed to
withstand only those loads imposed
by correctly fitted child restraints. Un-
der no circumstance are they to be
used for adult seat belts or har-
nesses.
Inspect the lower anchors by insert-
ing your fingers into the lower anchor
area and feeling to make sure there
are no obstructions over the LATCH
anchors, such as seat belt webbingor seat cushion material. The child
restraint will not be secured properly
if the LATCH anchors are obstructed.
Front-facingFollow these steps to install a front-facing child
restraint using LATCH:
1. Adjust the seatback so that it is upright.
Do not move the rear seatbacks with the child
restraints attached to them.
2. Position the child restraint on the seat. Al-
ways follow the child restraint manufacturer’s
instructions.
SSS0645
Front facing — step 3
1-26
Safety — seats, seat belts and supplemental restraint system
06.7.5/Z50-D/V5.0
Page 40 of 345
3. Secure the child restraint anchor attach-
ments to the LATCH lower anchors.
4. The back of the child restraint should be
secured against the vehicle seatback. If nec-
essary, adjust or remove the head restraint to
obtain the correct child restraint fit. See
“Head restraint adjustment” in this section.
When the head restraint is removed, store it
in a secure place. Be sure to install the head
restraint when the child restraint is removed.5. For child restraints that are equipped with
webbing mounted attachments, remove any
additional slack from the anchor attachments.
Press downward and rearward firmly in the
center of the child restraint with your knee to
compress the vehicle seat cushion and seat-
back while tightening the webbing of the
anchor attachments.
6. If the child restraint is equipped with a top
tether strap, route the top tether strap and
secure the tether strap to the tether anchor
point. See “Top tether strap child restraint” in
this section.7. Before placing the child in the child restraint,
hold child restraint near the LATCH attach-
ment and use force to push the child restraint
from side to side, and tug it forward to make
sure that it is securely held in place. It should
not move more than 1 in (25 mm). If it does
move more than 1 in (25 mm), pull again on
the anchor attachments to further tighten the
child restraint. If you are unable to properly
secure the restraint, move the restraint to
another seating position and try again, or try a
different child restraint. Not all child restraints
fit in all types of vehicles.
8. Check to make sure the child restraint is
properly secured prior to each use. If the
SSS0646
Front facing — step 3
SSS0647
Front facing — step 5
SSS0638
Front facing — step 7
Safety — seats, seat belts and supplemental restraint system
1-27
06.7.5/Z50-D/V5.0
Page 41 of 345
child restraint is loose, repeat steps 4
through 7.
Rear-facingFollow these steps to install a rear-facing child
restraint using LATCH:
1. Adjust the seatback so that it is upright.
Do not move the rear seatbacks with the child
restraints attached to them.
2. Position the child restraint on the seat. Al-
ways follow the child restraint manufacturer’s
instructions.3. Secure the child restraint anchor attach-
ments to the LATCH lower anchors.
SSS0648
Rear facing — step 3
SSS0649
Rear facing — step 3
1-28
Safety — seats, seat belts and supplemental restraint system
06.7.5/Z50-D/V5.0
Page 42 of 345
4. For child restraints that are equipped with
webbing mounted attachments, remove any
additional slack from the anchor attachments.
Press downward and rearward firmly in the
center of the child restraint with your hand to
compress the vehicle seat cushion and seat-
back while tightening the webbing of the
anchor attachments.5. Before placing the child in the child restraint,
hold the child restraint near the LATCH at-
tachment and use force to push the child
restraint from side to side, and tug it forward
to make sure that it is securely held in place.
It should not move more than 1 in (25 mm). If
it does move more than 1 in (25 mm), pull
again on the anchor attachments to further
tighten the child restraint. If you are unable to
properly secure the restraint, move the re-
straint to another seating position and try
again, or try a different child restraint. Not all
child restraints fit in all types of vehicles.
6. Check to make sure the child restraint is
properly secured prior to each use. If thechild restraint is loose, repeat steps 4
through 5.
SSS0639
Rear facing — step 4
SSS0650
Rear facing — step 5
Safety — seats, seat belts and supplemental restraint system
1-29
06.7.5/Z50-D/V5.0
Page 43 of 345
CHILD RESTRAINT INSTALLATION
USING THE SEAT BELTS
WARNING
Even with the NISSAN Advanced Air
Bag System, never install a rear-
facing child restraint in the front pas-
senger seat. Supplemental front air
bags inflate with great force. A rear-
facing child restraint could be struck
by the supplemental front air bag in acrash and could seriously injure or
kill your child.
NISSAN recommends that child re-
straints be installed in the rear seat.
However, if you must install a for-
ward facing child restraint in the front
passenger seat, move the passenger
seat to the rearmost position. Also,
be sure the front passenger air bag
status light is illuminated to indicate
the passenger air bag is OFF. See
“Front passenger air bag and status
light” in this section for details.
The three-point seat belt in your ve-
hicle is equipped with an automatic
locking mode retractor which must
be used when installing a child re-
straint.
Failure to use the retractor’s locking
mode will result in the child restraint
not being properly secured. The re-
straint could tip over or otherwise be
unsecured and cause injury to the
child in a sudden stop or collision.
Also, it can change the operation ofthe front passenger air bag. See
“Front passenger air bag and status
light” in this section.
A child restraint with a top tether
strap should not be used in the front
passenger seat.
The instructions in this section apply to child
restraint installation using the vehicle seat belts
in the rear seat or the front passenger seat.
SSS0100
1-30
Safety — seats, seat belts and supplemental restraint system
06.7.5/Z50-D/V5.0