key NISSAN MURANO 2007 1.G Quick Reference Guide

HEADLIGHT AIMING CONTROL SWITCH
(with Xenon headlamps, if so equipped)
Depending on the number of occupants in the vehicle and
the load it is carrying, the headlight axis may be higher
than desired. If the vehicle is traveling on a hilly road, the
headlights may directly hit the rearview mirror of the
vehicle ahead or the windshield of the oncoming vehicle.
The light axis can be lowered with the operation of the
switch.
 The larger the number designated on the switch, the lower the axis.
 When traveling without a heavy load or on a flat road, select position 0.
HEADLIGHT CONTROL AND TURN SIGNAL
CONTROL
HEADLIGHT SWITCH
 Turn the headlight switch to the position to turn
on the front parking, tail, license plate and instrument
panel lights.
 Turn the headlight switch to the position to turn on
the headlights. All other lights remain on.
AUTOMATIC HEADLIGHT OPERATION (if so equipped)
The autolight system allows the headlights to be set so they turn on and off automatically.
The autolight system can:

Turn on the headlights, front parking, tail, license plate and instrument panel lights
automatically when it is dark.
 Turn off all the lights when it is light.
 Keep all the lights on for 45 seconds after you turn the key to OFF and all doors
are closed.
TO ACTIVATE THE AUTOLIGHT SYSTEM :
 Turn the headlight switch to the AUTO position, then turn the ignition switch to ON.
TO DEACTIVATE THE AUTOLIGHT SYSTEM :
 Turn the headlight switch to the OFF, or position.
FOG LIGHT OPERATION
NOTE: The headlights must be on and the low beams selected for the fog lights to operate.

Turn the switch to the position to turn on the fog lights.
 Turn the switch to the OFF position to turn off the fog lights.

REMOTE KEYLESS ENTRY SYSTEM
LOCK DOORS Press the LPD0150 button to lock all doors.
UNLOCK DOORS Press the
lpd0151
button once to unlock the driver’s door only. Press the button again within 5 seconds to unlock all doors.
USING THE PANIC ALARM Press and hold the button for longer than 0.5 seconds. The panic alarm will sound and headlights will stay on for 25 seconds. The panic alarm stops when it has run for 25 seconds or when any button is pressed on the keyfob.
HORN BEEP FEATURE The horn beep feature can be deactivated. Refer to the “Display screen, heater, air conditioner and audio systems” section in your Owner’s Manual for the procedure.
INTELLIGENT K EY SYSTEM
The Intelligent Key System allows you to lock or unlock your vehicle and start the engine.
NOTE: It is important to make sure the Intelligent Key is with you (that is, in your pocket or purse).
 The operating range of the door and trunk lock/unlock function is approximately 31 in (0.8 m).
 Locking the vehicle - Push any door handle Request Switch 01 once.
 Unlocking the vehicle - Push any door handle Request Switch 01 once. The corresponding door will unlock. Push the door handle Request Switch 01 again within 1 minute; all other doors will unlock.
STARTING THE ENGINE
 Push the ignition knob in.
 Confirm the Intelligent Key warning light is illuminated green.
 Turn the ignition knob to start the engine.
TURNING THE ENGINE OFF
 Shift transmission into P (Park).
 Turn ignition knob to LOCK position.
 An audible warning chime will sound when exiting the vehicle if the ignition knob is not completely turned to the OFF position.
01
XTRONIC CONTINUOUSL Y VARIABLE
T RANSMISSION
(CVT) ™
 The Xtronic CVT™ does not produce a gear change
sensation like traditional automatic transmissions.
 The transmission in your Murano requires a special fluid available only at your NISSAN dealer. No other fluid will
meet the exact requirements of the new Xtronic CVT™.

CONTROL PANEL DISPLAY WITH
N AVIGATION S YSTEM (if so equipped)
TRIP BUTTON
When the TRIP button is pressed, the following
modes will display on the screen:
 Warning messages (if there are any)
 TRIP 1 (Elapsed Time, Driving Distance,
Average Speed)
 TRIP 2 (Elapsed Time, Driving Distance, Average Speed)
 FUEL ECONOMY (Average Fuel Economy, Distance to Empty)
 MAINTENANCE (Engine Oil, Tire Rotation)
 OFF
MAINTENANCE ITEMS
You can set the engine oil and the tire rotation interval. To display the setting of the
maintenance interval, select the ENGINE O IL or TIRE R OTATION key using the joystick
and press the ENTER button.
To set the maintenance interval, select the MAINTENANCE SCHEDULE key by
using the joystick and pushing the joystick to the right or left. To reset the maintenance
interval, select the RESET key using the joystick and press the ENTER button.
CLOCK/SE T ADJUSTMENT

The clock on the display screen can be adjusted using the joystick and the following
procedure.

 Press the SETTING button, then select SYSTEM SETTINGS from the menu on
the display screen.
 Next select CLOCK to enter the CLOCK SETTINGS mode.
 Then select the HOURS or MINUTES key and hold the joystick left or right to adjust
the time. After the desired time is shown on the display screen, press the BACK
button to store.
Refer to both the Navigation System Owner’s Manual and your Owner’s Manual for
additional information.
MANUAL SHIFT MODE (if so equipped)
 When the shift selector lever is shifted from D (Drive) to the manual shift gate, the
transmission enters the manual shift mode.
 In the manual shift mode, shift range is displayed on the position indicator in the meter.
 When shifting up, move the shift selector lever to the + (up) side. (Shifts to higher range.)
 When shifting down, move the shift selector lever to the - (down) side. (Shifts to lower
range.)
 In manual shift mode, the transmission automatically shifts down to M1 (first) before
the vehicle comes to a stop. When accelerating again, it is necessary to shift up to the
desired range.
 When canceling the manual shift mode, return the shift selector lever to the D (Drive)
position. The transmission returns to the normal driving mode.

AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function.
 Entry/exit function.
MEMORY STOR AGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic
driver positioner memory. Follow these procedures to set driver preferences.
SET THE DESIRED POSITIONING
1. Set the shift selector lever to the P (Park) position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and

outside mirrors to the desired positions.
3. Press the
SET (memory) button and within 5 seconds press the position button (1 or
2) for at least 1 second until the indicator light illuminates. The position is now stored
in memory.
LINK TO KEYFOB
 Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
lpd0151
button on the remote.
 A keyfob can be linked to each memory button.
 If memory positioning is reset to a new location, it will be necessary to re-link the keyfob.
RECALLING A MEMORY SETTING FROM THE MEMORY PAD
 With the ignition on and shift selector lever in the P (Park) position, press the position
button (1 or 2) for at least 1 second.
FROM THE KEYFOB
 If properly linked, operation of the
lpd0151
button will automatically return the driver’s seat,
accelerator and brake pedals, and outside mirrors to the memorized position.
ENTRY/ EXIT FUNCTION
The driver’s seat automatically moves to allow the driver to get into and out of the driver’s
seat more easily. The driver’s seat slides backward when:
 The driver’s door is opened with the ignition switch in the LOCK position.
The driver’s seat returns to the previous position when:
 The key is inserted into the ignition switch.
 The ignition switch is pushed with the driver’s door closed (Intelligent Key models)
 The ignition switch is placed in the ON position.
POWER SEAT AND PEDAL ADJUSTMENTS
(if so equipped)
PEDAL POSITION ADJUSTMENT
(if so equipped)
 Push the switch 01 forward or backward to move
the brake and accelerator pedal to the desired
position. Only adjust the pedals when the shift
selector lever is in P (Park.)
SEAT P OSITION ADJUSTMENT
 Move the control 02 forward or backward to adjust the seat cushion forward or backward.
010203
04
FUEL-FILLER DOOR
The fuel-filler door automatically unlocks when the driver’s
door is unlocked.
 With the driver’s door unlocked, push the right side of
the fuel-filler door to open.
 To lock, close the fuel-filler door and lock the
driver’s door.

SEAT BELT WARNING LIGHT AND CHIME
 The light and chime remind you to fasten your seat belts. The
light illuminates whenever the ignition key is turned to the ON
or START position and remains illuminated until the driver’s seat
belt is fastened. At the same time, the chime sounds for about 6
seconds unless the driver’s seat belt is securely fastened.
 The seat belt warning light may also illuminate if the front passenger’s seat belt is
not fastened when the front passenger’s seat is occupied. For 5 seconds after the
ignition switch is in the ON position, the system does not activate the warning light
for the front passenger.
Refer to the Owner’s Manual for detailed information regarding seat belt usage.
FRONT-PASSENGER AIR BAG STATUS LIGHT
This vehicle is equipped with the Nissan Advanced Air Bag system. Under some conditions, depending on the type of occupant or object detected in the front passenger seat by the occupant classification sensor, the front-passenger air bag is designed to automatically turn OFF. When the front-passenger air bag is OFF, the front-passenger air bag status light will illuminate*. For example:
 When the system detects that the front-passenger’s seat is occupied by a small adult, child or child restraint as outlined in the Owner’s Manual, the will illuminate to indicate that the front-passenger air bag is OFF and will not inflate in a crash.
 When the front-passenger’s seat is occupied and the passenger meets the conditions outlined in the Owner’s Manual, the will not illuminate to indicate that the front-passenger air bag is operational.
*When the system detects that the front-passenger’s seat is unoccupied, the passenger air bag status light will not illuminate even though the front-passenger air bag is OFF.
Refer to the Owner’s Manual for detailed information regarding the Nissan Advanced Air Bag System.
TIRE PRESSURE MONITORING SYSTEM (if so equipped)
This system monitors tire pressure. Please remember, this system does not detect a sudden drop in tire pressure (for example, a blowout while driving). It also does not monitor the air pressure in the spare tire.
Tire pressure is affected by temperature. Low outside temperature causes lower tire pressure. This may cause the low tire pressure warning light to illuminate.
If the low tire pressure warning light comes on, check the tire pressure in all four tires.
Adjust the low tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light off.
If TPMS is not functioning properly, the low tire pressure warning light will flash for approximately 60 seconds when the key is turned on. The light will remain on after the 60 seconds. Have the system checked by a NISSAN dealer.