ignition NISSAN MURANO 2013 2.G Owners Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2013, Model line: MURANO, Model: NISSAN MURANO 2013 2.GPages: 507, PDF Size: 4.61 MB
Page 383 of 507
![NISSAN MURANO 2013 2.G Owners Manual Black plate (381,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSD0336B
AWD WARNING LIGHTGUID-9D8CB64F-35DD-4A37-956F-52AA71579753The AWD warning light is located in the meter.
The AWD warning light illuminat NISSAN MURANO 2013 2.G Owners Manual Black plate (381,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSD0336B
AWD WARNING LIGHTGUID-9D8CB64F-35DD-4A37-956F-52AA71579753The AWD warning light is located in the meter.
The AWD warning light illuminat](/img/5/332/w960_332-382.png)
Black plate (381,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSD0336B
AWD WARNING LIGHTGUID-9D8CB64F-35DD-4A37-956F-52AA71579753The AWD warning light is located in the meter.
The AWD warning light illuminates when the
ignition switch is pushed to the ON position. It
turns off soon after the engine is started.
If any malfunction occurs in the AWD systemwhile the engine is running, the warning light will
come on.
The warning light may blink rapidly (about twice
per second) while trying to free a stuck vehicle
due to high powertrain oil temperature. The
driving mode may change to 2WD. The AUTO
mode may change to the LOCK mode before the
warning light blinks. If the warning light blinks
rapidly during operation, stop the vehicle with
the engine idling in a safe place immediately.
Then if the light turns off after a while, you can
continue driving.
A large difference between the diameters of
front and rear wheels will make the warning light
blink slowly (about once per two seconds) . Pull
off the road in a safe area, and idle the engine.
Check that all tire sizes are the same, tire
pressure is correct and tires are not worn.
CAUTION
.
If the warning light remains on after
the above operation, have your
vehicle checked by a NISSAN dealer
as soon as possible.
. If the warning light comes on while
driving there may be a malfunction
in the AWD system. Reduce the
vehicle speed and have your vehicle checked by a NISSAN dealer as
soon as possible.
. The powertrain may be damaged if
you continue driving with the warn-
ing light blinking.
. Never drive on dry hard surface
roads in the LOCK mode, as this
will overload the powertrain and
may cause a serious malfunction.
Starting and driving5-35
Condition:
Page 384 of 507
![NISSAN MURANO 2013 2.G Owners Manual Black plate (382,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5-36Starting and driving
GUID-6A33C11E-91A4-41FA-95B0-22BCFAAF7D4F
SSD0488
WARNING
.Do not stop or park the vehicle over
flammable materials such NISSAN MURANO 2013 2.G Owners Manual Black plate (382,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5-36Starting and driving
GUID-6A33C11E-91A4-41FA-95B0-22BCFAAF7D4F
SSD0488
WARNING
.Do not stop or park the vehicle over
flammable materials such](/img/5/332/w960_332-383.png)
Black plate (382,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5-36Starting and driving
GUID-6A33C11E-91A4-41FA-95B0-22BCFAAF7D4F
SSD0488
WARNING
.Do not stop or park the vehicle over
flammable materials such as dry
grass, waste paper or rags. They
may ignite and cause a fire.
. Safe parking procedures require
that both the parking brake be set
and the transmission placed into P
(Park) . Failure to do so could cause
the vehicle to move unexpectedly or
roll away and result in an accident.
Make sure the selector lever has
been pushed as far forward as it can go and cannot be moved without
depressing the foot brake pedal.
. Never leave the engine running
while the vehicle is unattended.
. Do not leave children unattended
inside the vehicle. They could un-
knowingly activate switches or con-
trols. Unattended children could
become involved in serious acci-
dents.
1. Firmly apply the parking brake.
2. Move the selector lever to the P (Park) position. 3. To help prevent the vehicle from rolling into
traffic when parked on an incline, it is a good
practice to turn the wheels as illustrated.
.HEADED DOWNHILL WITH CURB:*1
Turn the wheels into the curb and move
the vehicle forward until the curb side
wheel gently touches the curb.
.HEADED UPHILL WITH CURB:*2
Turn the wheels away from the curb and
move the vehicle back until the curb side
wheel gently touches the curb.
.HEADED UPHILL OR DOWNHILL, NOCURB:
*3
Turn the wheels toward the side of the
road so the vehicle will move away from
the center of the road if it moves.
4. Push the ignition switch to the LOCK
position.
PARKING/PARKING ON HILLS
Condition:
Page 387 of 507
![NISSAN MURANO 2013 2.G Owners Manual Black plate (385,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
Normal operationGUID-2399D9B9-0F57-4BAD-9F01-56588EEEEE14The ABS operates at speeds above 3 to 6 MPH
(5 to 10 km/h). The speed varies according t NISSAN MURANO 2013 2.G Owners Manual Black plate (385,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
Normal operationGUID-2399D9B9-0F57-4BAD-9F01-56588EEEEE14The ABS operates at speeds above 3 to 6 MPH
(5 to 10 km/h). The speed varies according t](/img/5/332/w960_332-386.png)
Black plate (385,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
Normal operationGUID-2399D9B9-0F57-4BAD-9F01-56588EEEEE14The ABS operates at speeds above 3 to 6 MPH
(5 to 10 km/h). The speed varies according to
road conditions.
When the ABS senses that one or more wheels
are close to locking up, the actuator rapidly
applies and releases hydraulic pressure. This
action is similar to pumping the brakes very
quickly. You may feel a pulsation in the brake
pedal and hear a noise from under the hood or
feel a vibration from the actuator when it is
operating. This is normal and indicates that the
ABS is operating properly. However, the pulsa-
tion may indicate that road conditions are
hazardous and extra care is required while
driving.
GUID-6F99BD6B-AA3F-475B-9D6B-0401F20418AFThe Vehicle Dynamic Control (VDC) system
uses various sensors to monitor driver inputs
and vehicle motion. Under certain driving con-
ditions, the VDC system helps to perform the
following functions.
.Controls brake pressure to reduce wheel
slip on one slipping drive wheel so power is
transferred to a non slipping drive wheel on
the same axle.
. Controls brake pressure and engine output
to reduce drive wheel slip based on vehicle
speed (traction control function) .
. Controls brake pressure at individual wheels
and engine output to help the driver maintain
control of the vehicle in the following
conditions:
— understeer (vehicle tends to not follow
the steered path despite increased
steering input)
— oversteer (vehicle tends to spin due to certain road or driving conditions) .
The VDC system can help the driver to maintain
control of the vehicle, but it cannot prevent loss
of vehicle control in all driving situations.
When the VDC system operates, the
warning light in the instrument panel flashes so
note the following:
. The road may be slippery or the system may
determine some action is required to help keep the vehicle on the steered path.
. You may feel a pulsation in the brake pedal
and hear a noise or vibration from under the
hood. This is normal and indicates that the
VDC system is working properly.
. Adjust your speed and driving to the road
conditions.
See “Vehicle dynamic control (VDC) warning
light” in the “2. Instruments and controls”
section and “Vehicle Dynamic Control (VDC)
off indicator light” in the “2. Instruments and
controls” section.
If a malfunction occurs in the system, the
warning light comes on in the instrument panel.
The VDC system automatically turns off when
the warning light is on.
The VDC OFF switch is used to turn off the VDC
system. The VDC off indicator
illuminates to
indicate the VDC system is off. When the VDC
switch is used to turn off the system, the VDC
system still operates to prevent one drive wheel
from slipping by transferring power to a non
slipping drive wheel. The
warning light
flashes if this occurs. All other VDC functions
are off and the
warning light will not flash.
The VDC system is automatically reset to on
when the ignition switch is placed in the OFF
position then back to the ON position.
The computer has a built-in diagnostic feature
Starting and driving5-39
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM
Condition:
Page 394 of 507
![NISSAN MURANO 2013 2.G Owners Manual Black plate (392,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
6-2In case of emergency
GUID-6A75B42D-D28E-4CDF-84D2-DC5652B93673
SIC2574
Push the switch on to warn other drivers when
you must stop or park und NISSAN MURANO 2013 2.G Owners Manual Black plate (392,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
6-2In case of emergency
GUID-6A75B42D-D28E-4CDF-84D2-DC5652B93673
SIC2574
Push the switch on to warn other drivers when
you must stop or park und](/img/5/332/w960_332-393.png)
Black plate (392,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
6-2In case of emergency
GUID-6A75B42D-D28E-4CDF-84D2-DC5652B93673
SIC2574
Push the switch on to warn other drivers when
you must stop or park under emergency condi-
tions. All turn signal lights will flash.
WARNING
.If stopping for an emergency, be
sure to move the vehicle well off the
road.
. Do not use the hazard warning
flashers while moving on the high-
way unless unusual circumstances
force you to drive so slowly that
your vehicle might become a hazard to other traffic.
. Turn signals do not work when the
hazard warning flasher lights are
on.
The flasher can be actuated with the ignition
switch in any position.
Some state laws may prohibit the use of
the hazard warning flasher switch while
driving.
GUID-A4BE01F9-B39B-4F16-AEA3-8AD0D549DC73To shut off the engine in an emergency situation
while driving perform the following procedure:
. Rapidly push the push-button ignition switch
3 consecutive times in less than 1.5
seconds, or
. Push and hold the push-button ignition
switch for more than 2 seconds.
HAZARD WARNING FLASHER
SWITCH EMERGENCY ENGINE SHUT OFF
Condition:
Page 406 of 507
![NISSAN MURANO 2013 2.G Owners Manual Black plate (404,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
6-14In case of emergency
SCE0871
6.Push the ignition switch to the “ACC”
position. Then turn the compressor switch
to the ON (−) position a NISSAN MURANO 2013 2.G Owners Manual Black plate (404,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
6-14In case of emergency
SCE0871
6.Push the ignition switch to the “ACC”
position. Then turn the compressor switch
to the ON (−) position a](/img/5/332/w960_332-405.png)
Black plate (404,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
6-14In case of emergency
SCE0871
6.Push the ignition switch to the “ACC”
position. Then turn the compressor switch
to the ON (−) position and inflate the tire up
to the pressure that is specified on the tire
and loading information label affixed to the
driver’s side center pillar if possible, or to the
minimum of 180 kPa (26 psi) . Turn the air
compressor off briefly in order to check the
tire pressure with the pressure gauge.
If the tire is inflated to higher than the
specified pressure, lower the tire pressure
by releasing air with the pressure release
valve. NOTE:
The compressor tire pressure gauge
may show a pressure reading of 87 psi
(600 kPa) for about 30 seconds while
inflating the tire. The pressure gauge is
indicating the pressure inside the sea-
lant can. When the sealant has been
injected into the tire the pressure
gauge will drop and indicate actual tire
pressure.
WARNING
.
To avoid serious personal injury
while using the emergency tire
puncture repair kit:
— Securely tighten the compressor
hose to the tire valve. Failure to
do so can cause the sealant to
spray into the air and get into
your eyes or on the skin.
. Do not stand directly beside the
damaged tire while it is being
inflated because of the risk of the
rupture. If there are any cracks or
bumps, turn the compressor off
immediately.
If the tire pressure does not increase to 180kPa (26 psi) within 10 minutes, the tire
may be seriously damaged and
the tire
cannot be repaired with this tire repair
kit. Contact a NISSAN dealer.
7. When the tire pressure is at the specified amount, turn the air compressor off. If the
pressure cannot be inflated to the specified
amount, the air compressor can be turned
off at the minimum of 180 kPa (26 psi) .
Remove the power plug from the power
outlet and quickly remove the hose from the
tire valve. Attach the protective cap and
valve cap. Properly stow the emergency tire
puncture repair kit in the trunk.
CAUTION
To avoid serious personal injury when
stowing the emergency tire puncture
repair kit:
.Keep the sealant bottle screwed
into the compressor. Failure to do
so can cause the sealant to spray
into the air and get into your eyes or
on the skin.
8. Immediately drive the vehicle for 10 minutes or 3 km (2 miles) at a speed of 80 km/h (50
MPH) or less.
Condition:
Page 408 of 507
![NISSAN MURANO 2013 2.G Owners Manual Black plate (406,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
6-16In case of emergency
.Whenever working on or near a
battery, always wear suitable eye
protectors (for example, goggles or
industrial safety s NISSAN MURANO 2013 2.G Owners Manual Black plate (406,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
6-16In case of emergency
.Whenever working on or near a
battery, always wear suitable eye
protectors (for example, goggles or
industrial safety s](/img/5/332/w960_332-407.png)
Black plate (406,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
6-16In case of emergency
.Whenever working on or near a
battery, always wear suitable eye
protectors (for example, goggles or
industrial safety spectacles) and
remove rings, metal bands, or any
other jewelry. Do not lean over the
battery when jump starting.
. Do not attempt to jump start a
frozen battery. It could explode
and cause serious injury.
. Your vehicle has an automatic en-
gine cooling fan. It could come on at
any time. Keep hands and other
objects away from it.
SCE0719
WARNING
Always follow the instructions below.
Failure to do so could result in damage
to the charging system and cause
personal injury.
1. If the booster battery is in another vehicle
*B, position the two vehicles (*Aand*B)
to bring their batteries into close proximity to
each other.
Do not allow the two vehicles to touch. 2. Apply the parking brake. Move the selector
lever to the P (Park) position. Switch off all
unnecessary electrical systems (lights, hea-
ter, air conditioner, etc.).
3. Remove vent caps on the battery (if so equipped) . Cover the battery with a firmly
wrung out moist cloth to reduce explosion
hazard.
4. Connect jumper cables in the sequence as illustrated (
*1?*2?*3?*4) .
If the battery is discharged, the ignition
switch cannot be moved from the OFF
position. Connect the jumper cables to
the booster vehicle
*Bbefore pushing
the ignition switch.
CAUTION
. Always connect positive (+) to posi-
tive (+) and negative (−) to body
ground (for example, as illustrated) ,
not to the battery.
. Make sure the jumper cables do not
touch moving parts in the engine
compartment and that the cable
clamps do not contact any other
metal.
Condition:
Page 409 of 507
![NISSAN MURANO 2013 2.G Owners Manual Black plate (407,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5. Start the engine of the booster vehicle*B
and let it run for a few minutes.
6. Keep the engine speed of the booster
vehicle
*Bat about 2,000 r NISSAN MURANO 2013 2.G Owners Manual Black plate (407,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5. Start the engine of the booster vehicle*B
and let it run for a few minutes.
6. Keep the engine speed of the booster
vehicle
*Bat about 2,000 r](/img/5/332/w960_332-408.png)
Black plate (407,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5. Start the engine of the booster vehicle*B
and let it run for a few minutes.
6. Keep the engine speed of the booster
vehicle
*Bat about 2,000 rpm, and start
the engine of the vehicle
*Abeing jump
started.
CAUTION
Do not keep the starter motor engaged
for more than 10 seconds. If the engine
does not start right away, place the
ignition switch in the OFF position and
wait 10 seconds before trying again.
7. After starting your engine, carefully discon- nect the negative cable and then the positive
cable (
*4?*3?*2?*1) .
8. Replace the vent caps (if so equipped). Be sure to dispose of the cloth used to cover
the vent holes as it may be contaminated
with corrosive acid.
GUID-C5D48490-7786-4F89-AA89-502A3A18D71FDo not attempt to start the engine by pushing.
CAUTION
Continuously Variable Transmission
(CVT) models cannot be push-started
or tow-started. Attempting to do so may
cause transmission damage.
GUID-F7BD7B71-591F-48BF-AF5A-8E7582E463D3
CAUTION
.Do not continue to drive if your
vehicle overheats. Doing so could
cause engine damage or a vehicle
fire.
. To avoid the danger of being
scalded, never remove the radiator
cap while the engine is still hot.
When the radiator cap is removed,
pressurized hot water will spurt out,
possibly causing serious injury.
. Do not open the hood if steam is
coming out.
If your vehicle is overheating (indicated by an
extremely high temperature gauge reading) , or if
you feel a lack of engine power, detect abnormal
noise, etc., take the following steps:
1. Move the vehicle safely off the road, apply the parking brake and move the selector
lever to the P (Park) position.
Do not stop the engine.
2. Turn off the air conditioner. Open all the windows, move the heater or air conditioner
temperature control to maximum hot and fan
control to high speed.
In case of emergency6-17
PUSH STARTING IF YOUR VEHICLE OVERHEATS
Condition:
Page 413 of 507
![NISSAN MURANO 2013 2.G Owners Manual Black plate (411,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SCE0438
Two-Wheel Drive (2WD) models
Two-Wheel Drive (2WD) modelsGUID-F69CDF34-4EA1-44CF-824A-16A614B5B272NISSAN recommends that your vehicle be
NISSAN MURANO 2013 2.G Owners Manual Black plate (411,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SCE0438
Two-Wheel Drive (2WD) models
Two-Wheel Drive (2WD) modelsGUID-F69CDF34-4EA1-44CF-824A-16A614B5B272NISSAN recommends that your vehicle be](/img/5/332/w960_332-412.png)
Black plate (411,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SCE0438
Two-Wheel Drive (2WD) models
Two-Wheel Drive (2WD) modelsGUID-F69CDF34-4EA1-44CF-824A-16A614B5B272NISSAN recommends that your vehicle be
towed with the driving (front) wheels off the
ground or place the vehicle on a flat bed truck as
illustrated.
For All-Wheel Drive (AWD) models, see “All-
Wheel Drive (AWD) models” earlier in this
section.
CAUTION
.Never tow Continuously Variable
Transmission (CVT) models with
the front wheels on the ground or four wheels on the ground (forward
or backward) , as this may cause
serious and expensive damage to
the drivetrain. If it is necessary to
tow the vehicle with the rear wheels
raised, always use towing dollies
under the front wheels.
. When towing CVT models with the
front wheels on towing dollies:
— Push the ignition switch to the
ACC or ON position, and secure
the steering wheel in a straight-
ahead position with a rope or
similar device. — Move the selector lever to the N
(Neutral) position.
. When towing a CVT model with the
rear wheels on the ground (if you do
not use towing dollies): Always
release the parking brake.
In case of emergency6-21
Condition:
Page 429 of 507
![NISSAN MURANO 2013 2.G Owners Manual Black plate (427,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
GUID-706DBDF3-66DE-4E0B-A1AF-17943A0D7966When performing any inspection or mainte-
nance work on your vehicle, always take care
to prevent seriou NISSAN MURANO 2013 2.G Owners Manual Black plate (427,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
GUID-706DBDF3-66DE-4E0B-A1AF-17943A0D7966When performing any inspection or mainte-
nance work on your vehicle, always take care
to prevent seriou](/img/5/332/w960_332-428.png)
Black plate (427,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
GUID-706DBDF3-66DE-4E0B-A1AF-17943A0D7966When performing any inspection or mainte-
nance work on your vehicle, always take care
to prevent serious accidental injury to yourself or
damage to the vehicle. The following are general
precautions which should be closely observed.
WARNING
.Park the vehicle on a level surface,
apply the parking brake securely
and block the wheels to prevent
the vehicle from moving. Move the
selector lever to P (Park) .
. Be sure the ignition switch is in the
OFF or LOCK position when per-
forming any parts replacement or
repairs.
. If you must work with the engine
running, keep your hands, clothing,
hair and tools away from moving
fans, belts and any other moving
parts.
. It is advisable to secure or remove
any loose clothing and remove any
jewelry, such as rings, watches, etc.
before working on your vehicle.
. Always wear eye protection when-
ever you work on your vehicle. .
If you must run the engine in an
enclosed space such as a garage, be
sure there is proper ventilation for
exhaust gases to escape.
. Never get under the vehicle while it
is supported only by a jack. If it is
necessary to work under the vehicle,
support it with safety stands.
. Keep smoking materials, flame and
sparks away from fuel tank and the
battery.
. The fuel filter or fuel lines should be
serviced by a NISSAN dealer be-
cause the fuel lines are under high
pressure even when the engine is
off.
CAUTION
.Do not work under the hood while
the engine is hot. Turn the engine
off and wait until it cools down.
. Avoid direct contact with used en-
gine oil and coolant. Improperly
disposed engine oil, and engine
coolant and/or other vehicle fluids
can damage the environment. Al- ways conform to local regulations
for disposal of vehicle fluid.
. Never leave the engine or the CVT
related component harnesses dis-
connected while the ignition switch
is in the ON position.
. Never connect or disconnect the
battery or any transistorized com-
ponent while the ignition switch is
in the ON position.
. Your vehicle is equipped with an
automatic engine cooling fan. It may
come on at any time without warn-
ing, even if the ignition key is in the
OFF position and the engine is not
running. To avoid injury, always
disconnect the negative battery
cable before working near the fan.
This “8. Maintenance and do-it-yourself” section
gives instructions regarding only those items
which are relatively easy for an owner to perform.
A genuine NISSAN Service Manual is also
available. (See “Owner’s Manual/Service Man-
ual order information” in the “9. Technical and
consumer information” section.)
You should be aware that incomplete or
improper servicing may result in operating
Maintenance and do-it-yourself8-5
MAINTENANCE PRECAUTIONS
Condition:
Page 439 of 507
![NISSAN MURANO 2013 2.G Owners Manual Black plate (437,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
JUMP STARTINGGUID-8388D2A5-1AA4-4543-8945-3818D12359C5If jump starting is necessary, see “Jump starting”
in the “6. In case of emergency” NISSAN MURANO 2013 2.G Owners Manual Black plate (437,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
JUMP STARTINGGUID-8388D2A5-1AA4-4543-8945-3818D12359C5If jump starting is necessary, see “Jump starting”
in the “6. In case of emergency”](/img/5/332/w960_332-438.png)
Black plate (437,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
JUMP STARTINGGUID-8388D2A5-1AA4-4543-8945-3818D12359C5If jump starting is necessary, see “Jump starting”
in the “6. In case of emergency” section. If the
engine does not start by jump starting, the
battery may have to be replaced. Contact a
NISSAN dealer.
GUID-A57D0C74-2880-49D1-B6F8-A870230F48C1
CAUTION
.Do not ground accessories directly
to the battery terminal. Doing so will
bypass the variable voltage control
system and the vehicle battery may
not charge completely.
. Use electrical accessories with the
engine running to avoid discharging
the vehicle battery.
The variable voltage control system measures
the amount of electrical discharge from the
battery and controls voltage generated by the
generator.
GUID-C7A9F001-0CB6-4300-AC6F-E7BA2ACAD7EA
SDI2186
1. Power steering oil pump
2. Alternator
3. Drive belt auto-tensioner
4. Crankshaft pulley
5. Air conditioner compressor
WARNING
Be sure the ignition switch is in the OFF
or LOCK position before servicing drive
belt. The engine could rotate unexpect-
edly.
1. Visually inspect the belt for signs of unusual wear, cuts, fraying or looseness. If the belt is
Maintenance and do-it-yourself8-15
VARIABLE VOLTAGE CONTROL
SYSTEM (if so equipped) DRIVE BELT
Condition: