belt NISSAN MURANO 2013 2.G User Guide

Black plate (26,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-4Safety — Seats, seat belts and supplemental restraint system
SSS0793
Seat lifter (if so equipped):GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Pull up or push down the adjusting lever to
adjust the seat height until the desired position
is achieved.
SSS0684
Lumbar support (if so equipped):GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The lumbar support feature provides lower back
support to the driver.
Move the lever
*1up or down to adjust the
seatback lumbar area.
Power seat adjustmentGUID-2155E48C-B77E-4502-84B7-2AF110D60DE4
Operating tips:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407. The power seat motor has an auto-reset
overload protection circuit. If the motor
stops during operation, wait 30 seconds,
then reactivate the switch.
. Do not operate the power seat switch for a
long period of time when the engine is off.
This will discharge the battery.
See “Automatic drive positioner” in the “3. Pre-
driving checks and adjustments” section for the
seat position memory function (if so equipped).
Condition:

Black plate (27,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
JVR0038X
Forward and backward:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Moving the switch*Aforward or backward will
slide the seat forward or backward to the
desired position.
Pushing the front
*1or back*2end of the
slide switch
*Bwill slide the driver seat forward
or backward to the desired position (Cross-
Cabriolet models driver’s seat only).
Safety — Seats, seat belts and supplemental restraint system1-5
Condition:

Black plate (28,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-6Safety — Seats, seat belts and supplemental restraint system
JVR0039X
Reclining:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Move the recline switch*Abackward until the
desired angle is obtained. To bring the seatback
forward again, move the switch
*Aforward.
Push and hold the back
*2end of the reclining
switch
*Buntil the desired angle is obtained.
To bring the seatback forward again, push and
hold the front
*1end of the switch (Cross-
Cabriolet models driver’s seat only).
The reclining feature allows adjustment of the
seatback for occupants of different sizes for
added comfort and to help obtain proper seat
belt fit. (See “Precautions on seat belt usage”
later in this section.) Also, the seatback can be
reclined to allow occupants to rest when the vehicle is stopped and the transmission is in the
P (Park) position.
SSS1027
Seat lifter (if so equipped):GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Push the front or rear end of the switch up or
down to adjust the angle of the front portion or
height of the seat.
Condition:

Black plate (29,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS1028
Lumbar support (if so equipped):GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The lumbar support feature provides lower back
support to the driver.
Push the front
*1or back*2end of the switch
to adjust the seatback lumbar area.
SSS1172
Front passenger’s seatback switch
SSS1175
Remote walk-in switch
Walk-in function (front passenger seat,
CrossCabriolet models):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
CAUTION
. When operating the walk-in func-
tion, be sure not to contact any
moving parts to avoid possible in-
juries and/or damages.
. When operating the walk-in func-
tion, be sure that the front passen-
ger seat is not occupied by a
passenger and/or any objects to
avoid possible injuries and/or da-
mages.
. After operating the walk-in function,
be sure to return the seat to the
rearmost position and then tilt up
the seatback until it latches.
This feature makes it easier to get in and out of
the rear seat. Use the following procedure when
getting in and out of the rear seat on the
passenger’s side. If the sun visor is used, close it
to the original position before operating the
walk-in feature.
1. Push the front passenger’s seatback switch to fold down the seatback and unlock the
seat position.
Safety — Seats, seat belts and supplemental restraint system1-7
Condition:

Black plate (30,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-8Safety — Seats, seat belts and supplemental restraint system
Alternatively, you can push the remote walk-
in switch located on the instrument panel to
fold down the front passenger’s seatback
and unlock the seat position.
2. Slide the seat forward to the foremost
position manually.
3. Get in or out the vehicle.
4. Return the front passenger seat to the
rearmost position. To slide the front passen-
ger seat, see “Manual seat adjustment”
earlier in this section.
SSS1173
Driver’s seatback release (CrossCabrio-
let models)
GUID-116F27BD-8437-47A9-8270-AD99D91FA75DTo exit the rear seat from the driver’s side, pull
the strap behind the driver’s seat to release the
driver’s seatback. The driver’s seatback will tilt
forward so that you can exit the vehicle.
NOTE:
Pulling the strap behind the driver’s seat
does not slide the driver’s seat forward.
You cannot slide the driver’s seat manu-
ally.
WARNING
Before using the driver’s seatback re-
lease, be sure that the driver’s seat is
not occupied by a driver and/or any
objects to avoid possible injuries and/
or damage.
Condition:

Black plate (31,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS0569
REAR SEATS (Hardtop models)GUID-42670C07-8DEA-4731-BDEC-1C3F2B7295A1
FoldingGUID-8333E9E4-6111-43A4-8DC3-B860D3C64DA7
Before folding the rear seats:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407.Secure the seat belts on the seat belt hooks
on the side wall. (See “Seat belt hooks
(Hardtop models)” later in this section.)
. Disconnect and stow the center seat belt
and tongue into the retractor base. (See
“Rear center seat belt (Hardtop models)”
later in this section.)
. Always reconnect the center seat belt when
the seat is returned to the upright position.
. Remove drink containers from the rear cup
holder. To fold down the seatbacks:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Pull the strap on the rear seat*A. Pull the lever
*Bbeside the cargo area and fold the seat-
back.
SSS0821
To return the seatbacks:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Manual operation:
Lift up each seatback and push it to the upright
position until it is latched.
Power operation (if so equipped):
Push and hold the corresponding switch located
on the lower side of the instrument panel
*Bor
the right or left side in the cargo area
*A.
A beep sounds once and the seatback will be
returned automatically.
A beep sounds twice when the seatback is fully
returned to the seating position.
If the control unit detects any obstacle or
malfunctions while in the power operation, a
Safety — Seats, seat belts and supplemental restraint system1-9
Condition:

Black plate (32,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-10Safety — Seats, seat belts and supplemental restraint system
beep sounds for 4 seconds and the seatback
will return to the folded position automatically.
Check if there are any obstacles caught that
prevent seats from returning to the folded
position. See a NISSAN dealer if the beep still
sounds.
CAUTION
When operating the rear power seat-
back return, make sure that the vehicle
is stopped and the transmission is in
the P (Park) position.
WARNING
.Never allow anyone to ride in the
cargo area or on the rear seats
when they are in the fold-down
position. In a collision, people riding
in these areas are more likely to be
seriously injured or killed.
. Do not allow people to ride in any
area of your vehicle that is not
equipped with seats and seat belts.
Be sure everyone in your vehicle is
in a seat and using a seat belt
properly. .
Do not fold down the rear seats
when occupants are in the rear seat
area or any luggage is on the rear
seats.
. When folding or returning the seat-
backs to the upright position, to
avoid injury to yourself and others:
— Make sure that the seat path is
clear before moving the seat.
— Be careful not to allow hands or feet to get caught or pinched in
the seat.
. Properly secure all cargo to help
prevent it from sliding or shifting.
Do not place cargo higher than the
seatbacks. In a sudden stop or
collision, unsecured cargo could
cause personal injury.
. When returning the seatbacks, be
sure to attach the rear center seat
belt connector.
. Do not unfasten the rear center seat
belt connector except when folding
down the rear seat.
. When attaching the rear center seat
belt connector, be certain that the
seatbacks are completely secured in
the latched position and the rear center seat belt connector is com-
pletely secured.
. If the rear center seat belt connector
and the seatbacks are not secured
in the correct position, serious per-
sonal injury may result in an acci-
dent or sudden stop.
Condition:

Black plate (33,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS0227A
RecliningGUID-1BFE5C97-1FC3-4054-A6B3-17A9466D0C05Pull the reclining strap*Aand position the
seatback at the desired angle. Release the
reclining strap after positioning the seat at the
desired angle.
The reclining feature allows adjustment of the
seatback for occupants of different sizes to help
obtain proper seat belt fit. (See “Precautions on
seat belt usage” later in this section.) The
seatback may also be reclined to allow occu-
pants to rest when the vehicle is parked.
WARNING
. Do not ride in a moving vehicle
when the seatback is reclined. This
can be dangerous. The shoulder belt
will not be against your body. In an
accident, you could be thrown into it
and receive neck or other serious
injuries. You could also slide under
the lap belt and receive serious
internal injuries.
. For the most effective protection
when the vehicle is in motion, the
seat should be upright. Always sit
well back in the seat with both feet
on the floor and adjust the seat belt
properly. See “Precautions on seat
belt usage” later in this section.
. After adjustment, check to be sure
the seat is securely locked.
HEAD RESTRAINTSGUID-5E605952-D804-4293-B401-616CD7C38955
WARNING
Head restraints supplement the other
vehicle safety systems. They may pro-
vide additional protection against injury
in certain rear end collisions. Adjust the
head restraints properly, as specified in
this section. Check the adjustment after
someone else uses the seat. Do not
attach anything to the head restraint
stalks or remove the head restraint. Do
not use the seat if the head restraint
has been removed. If the head restraint
was removed, install and properly ad-
just the head restraint before an occu-
pant uses the seating position. Failure
to follow these instructions can reduce
the effectiveness of the head restraints.
This may increase the risk of serious
injury or death in a collision.
Safety — Seats, seat belts and supplemental restraint system1-11
Condition:

Black plate (34,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-12Safety — Seats, seat belts and supplemental restraint system
JVR0140X
The illustration shows the seating positions
equipped with head restraints and headrest.
For Hardtop models, the head restraints and the
headrest are adjustable.
For CrossCabriolet models, the front head
restraints are adjustable and the rear head
restraints are not removable or adjustable.
Indicates the seating position is equipped
with a head restraint.
Indicates the seating position is equipped
with an adjustable headrest (for Hardtop mod-
els) .
SSS0992
ComponentsGUID-D58E33DF-16BC-41B1-B4C5-AA96E133EBC71. Head restraint
2. Adjustment notches
3. Lock knob
4. Stalks
SSS0997
AdjustmentGUID-ACB994E3-70CF-4004-BDD8-BB431714EC1EAdjust the head restraint so the center is level
with the center of your ears.
Condition:

Black plate (35,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS0993
To raise the head restraint, pull it up.
SSS0994
To lower, push and hold the lock knob and push
the head restraint down.
SSS0995
RemovalGUID-FC0E7C18-BEC7-4083-8503-66512F55EE99Use the following procedure to remove the
adjustable head restraints.
1. Pull the head restraint up to the highestposition.
2. Push and hold the lock knob.
3. Remove the head restraint from the seat.
4. Store the head restraint properly in a secure place so it is not loose in the vehicle.
5. Reinstall and properly adjust the head
restraint before an occupant uses the
seating position.
Safety — Seats, seat belts and supplemental restraint system1-13
Condition: