phone NISSAN MURANO 2013 2.G Workshop Manual

Black plate (241,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SAA1978
Difference between predictive and actual
distances
GUID-B23DB747-73AB-40B0-A401-6731AEBFF5E1
Backing up on a steep uphill:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407When backing up the vehicle up a hill, the
distance guide lines and the vehicle width guide
lines are shown closer than the actual distance.For example, the display shows 3 ft (1 m) to the
place
*A, but the actual 3 ft (1 m) distance on
the hill is the place
*B. Note that any object on
the hill is viewed in the monitor further than it
appears.
SAA1979
Backing up on a steep downhill:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407When backing up the vehicle down a hill, the
distance guide lines and the vehicle width guide
lines are shown further than the actual distance.
For example, the display shows 3 ft (1 m) to the
place
*A, but the actual 3 ft (1 m) distance on
the hill is the place
*B. Note that any object on
Monitor, heater, air conditioner, audio, phone and voice recognition systems4-35
Condition:

Black plate (242,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
4-36Monitor, heater, air conditioner, audio, phone and voice recognition systems
the hill is viewed in the monitor closer than it
appears.
SAA1923
Backing up near a projecting object:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The predictive course lines*Ado not touch the
object in the display. However, the vehicle may
hit the object if it projects over the actual
backing up course.
SAA1980
Backing up behind a projecting object:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The position*Cis shown further than the
position
*Bin the display. However, the
position
*Cis actually at the same distance
as the position
*A. The vehicle may hit the
object when backing up to the position
*Aif
the object projects over the actual backing up
Condition:

Black plate (243,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
course.
HOW TO ADJUST THE SCREENGUID-676089A8-8409-437E-AF8B-BB7CEF8236C5To adjust the Display ON/OFF, Brightness, Tint,
Color, Contrast and Black Level of the RearView
Monitor, push the SETTING button with the
RearView Monitor on, select the item key and
adjust the level using the multi-function con-
troller.
Do not adjust the Brightness, Tint, Color,
Contrast and Black Level of the RearView
Monitor while the vehicle is moving. Make sure
the parking brake is firmly applied.
OPERATING TIPSGUID-8F6C8715-08BF-4B5F-BC87-114E3BD955AA.When the selector lever is shifted to the R
(Reverse) position, the monitor screen auto-
matically changes to the RearView Monitor
mode. However, the radio can be heard.
. When the temperature is extremely high or
low, the screen may not clearly display
objects. This is not a malfunction.
. When strong light directly enters the cam-
era, objects may not be displayed clearly.
This is not a malfunction.
. Vertical lines may be seen in objects on the
screen. This is due to strong reflected light
from the bumper. This is not a malfunction.
. The screen may flicker under fluorescent
light. This is not a malfunction. .
The colors of objects on the RearView
Monitor may differ somewhat from the actual
color of objects. This is not a malfunction.
. Objects on the monitor may not be clear in a
dark environment. This is not a malfunction.
. If dirt, rain or snow accumulates on the
camera, the RearView Monitor may not
display object clearly. Clean the camera.
. Do not use alcohol, benzine or thinner to
clean the camera. This will cause discolora-
tion. To clean the camera, wipe with a cloth
dampened with diluted mild cleaning agent
and then wipe with a dry cloth.
. Do not damage the camera as the monitor
screen may be adversely affected.
. Do not use wax on the camera window.
Wipe off any wax with a clean cloth
dampened with mild detergent diluted with
water.
. The MOD system will not operate if the
washer fluid is at a low level. Refill the
washer fluid if the level is low. (See
“Window washer fluid” in the “8. Mainte-
nance and do-it-yourself” section.)
MOVING OBJECT DETECTION (MOD)
FUNCTION
GUID-AEEBBBF8-0266-4DE4-9FF1-58ED071056E6The Moving Object Detection (MOD) system
can inform the driver of moving objects when
driving out of garages, maneuvering into parking
lots and in other such instances.
The MOD system detects moving objects by
using image processing technology on the
image shown in the display. The RearView
camera is equipped with the automatic washer
function using window washer fluid.
When the shift selector is in the R (Reverse)
position and the vehicle speed is approximately
5 MPH (8 km/h) or less, the MOD system
detects moving objects in the RearView Monitor.
The MOD system will not operate if the lift gate/
trunk is open or the washer fluid is at a low level.
WARNING
.The MOD system is not a substitute
for proper vehicle operation and
does not prevent contact with the
objects surrounding the vehicle.
When maneuvering, always use the
outside mirror and RearView mirror
and turn and look to check the
surroundings to make sure it is safe
to maneuver.
Monitor, heater, air conditioner, audio, phone and voice recognition systems4-37
Condition:

Black plate (244,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
4-38Monitor, heater, air conditioner, audio, phone and voice recognition systems
.The MOD system is not designed to
detect surrounding stationary ob-
jects.
If the MOD system detects moving objects
behind the vehicle, a yellow frame will be
displayed on the camera image and a chime
sounds.
When the MOD system detects a moving object
behind the vehicle, the yellow frame will be
displayed on the view where the objects are
detected and a chime will sound once. While the
MOD system continues to detect moving
objects, the yellow frame continues to be
displayed.
When dirt is detected on the camera during
driving, a camera washer operates automatically.
The washer will stop operation after a period of
time.
WARNING
. Do not use the MOD system when
towing a trailer. The system may not
function properly.
. Excessive noise (for example, audio
system volume or open vehicle
window) will interfere with the chime sound, and it may not be
heard.
. The MOD system performance will
be limited according to environmen-
tal conditions and surrounding ob-
jects such as:
— When there is low contrast be-
tween background and the mov-
ing objects
— When there is blinking source of light.
— When strong light such as an- other vehicle’s headlight or sun-
light is present.
— When there is dirt, water drops or snow on the camera lens.
— When the position of the moving objects in the display is not
changed.
. The MOD system might detect
something like flowing water dro-
plets on the camera lens, white
smoke from the muffler, moving
shadows, etc.
. The MOD system may not function
properly depending on the speed,
direction, distance or shape of the moving objects.
. If your vehicle sustains damage to
the parts where the camera is
installed, leaving it misaligned or
bent, the sensing zone may be
altered and the MOD system may
not detect objects properly.
Condition:

Black plate (245,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
JVH0365X
Turning the MOD system on or offGUID-6FFC799C-38DE-47D7-9694-F22E33AA88F31. Push the SETTING button, select the “DriverAssistance” key and push the ENTER
button.
JVH0345X
2. Then select the “Moving Object Detection
(MOD)” key and push the ENTER button.
JVH0344X
When the MOD system is turned on, the MOD
icon
*1is displayed.
MOD malfunctionGUID-9253042E-52DF-4D2C-9CC8-EB45D6EC9B51When the yellow MOD icon is displayed in the
view, the system is not functioning properly. This
will not hinder normal driving operation but the
system should be inspected by a NISSAN
dealer.
Monitor, heater, air conditioner, audio, phone and voice recognition systems4-39
Condition:

Black plate (246,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
4-40Monitor, heater, air conditioner, audio, phone and voice recognition systems
Camera maintenanceGUID-D122E1B9-F1F3-4CC4-AB1D-AEAA63E13D58If dirt, rain or snow accumulates on the camera,
the MOD system may not operate properly.
Clean the camera.
The camera washer operates automatically
when dirt is detected on the camera during
driving. The washer then stops operation after a
period of time.
GUID-5620F45C-95A1-4691-9F0B-E47071C3B894
SAA1991
Center ventilators
SAA1990
Side ventilators
SAA1066
Rear ventilators (for Hardtop models)
SAA0564B
Rear ventilators (for CrossCabriolet models)
VENTILATORS
Condition:

Black plate (247,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
Open or close, and adjust the air flow direction
of ventilators.
: This symbol indicates that the ventilators areclosed.
: This symbol indicates that the ventilators are
open.
GUID-FC7D28D6-FA80-42E2-A3B4-6CF8ABD33B6A
WARNING
. The air conditioner cooling function
operates only when the engine is
running.
. Do not leave children or adults who
would normally require the support
of others alone in your vehicle. Pets
should not be left alone either. On
hot, sunny days, temperatures in a
closed vehicle could quickly become
high enough to cause severe or
possibly fatal injuries to people or
animals.
. Do not use the recirculation mode
for long periods as it may cause the
interior air to become stale and the
windows to fog up.
Start the engine and operate the heater and air
conditioner system.
You can individually set the driver and front
passenger side temperature using each tem-
perature control buttons.
SAA2723
Models with navigation system
SAA1520
Models without navigation system
Monitor, heater, air conditioner, audio, phone and voice recognition systems4-41
HEATER AND AIR CONDITIONER
Condition:

Black plate (248,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
4-42Monitor, heater, air conditioner, audio, phone and voice recognition systems
For the models with the color display screen,
push the “STATUS” button to display the heater
and air conditioner status screen. (See “How to
use STATUS button” earlier in this section.)
SAA2040
Type A1. Temperature control button (driver side)
2. “AUTO” automatic air conditioner ON button
3. “
” front defroster button
4. “
” fan speed control dial/OFF button
5. “
” intake air control button
6. “MODE” manual air flow control button
7. Temperature control button (passenger side)
8. “A/C” air conditioner ON/OFF button
9. “
” rear window defroster button (See “Rear
window and outside mirror defroster switch” in
the “2. Instruments and controls” section.)
10. “
” upper vent system button
11. “DUAL” zone control ON/OFF button
Condition:

Black plate (249,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SAA2834
Type B1. “AUTO” automatic air conditioner ON button/Temperature control dial (driver side)
2. “A/C” air conditioner ON/OFF button
3. “
” intake air control button
4. “
” fan speed control dial/ON/OFF button
5. “
” upper vent system button
6. “DUAL” zone control ON/OFF button/Tempera- ture control dial (passenger side)
7. “
” front defroster button
8. “
” rear window defroster button (See “Rear
window and outside mirror defroster switch” in
the “2. Instruments and controls” section.)
9. “MODE” manual air flow control button
AUTOMATIC OPERATIONGUID-0FE56354-85D2-43F0-AEA7-6DFAE35EC270
Cooling and/or dehumidified heating
(AUTO)
GUID-501AABAA-75ED-4A8C-BDC5-F83D84729E33This mode may be used all year round. The
system works automatically to control the inside
temperature, air flow distribution and fan speed
after the preferred temperature is set manually.
1. Push the “AUTO” button on. (The indicator on the button will illuminate and AUTO will
be displayed.)
2. Operate the driver side temperature control buttons (type A) or dial (type B) to set the
desired temperature.
Adjust the temperature to about 758F
(248C) for normal operation.
.The temperature of the passenger com-partment will be maintained automati-
cally. Air flow distribution and fan speed
will also be controlled automatically.
3. You can individually set driver and front passenger side temperature using each
temperature control buttons (type A) or dial
(type B) . When the “DUAL” button is pushed
or the passenger side temperature control
buttons (type A) or dial (type B) is/are
operated, the DUAL indicator will come on.
To turn off the passenger side temperature
control, push the “DUAL” button.
Monitor, heater, air conditioner, audio, phone and voice recognition systems4-43
Condition:

Black plate (250,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
4-44Monitor, heater, air conditioner, audio, phone and voice recognition systems
A visible mist may be seen coming from the
ventilators in hot, humid conditions as the air is
cooled rapidly. This does not indicate a mal-
function.
Heating (A/C OFF)GUID-C4D96DF4-D0D2-4751-8F78-451CD5632566The air conditioner does not activate in this
mode. When you need to heat only, use this
mode.
1. Push the “A/C” button. (The A/C indicatorwill turn off.)
2. Operate the temperature control buttons (type A) or dial (type B) to set the desired
temperature.
. The temperature of the passenger compart-
ment will be maintained automatically. Air
flow distribution and fan speed are also
controlled automatically.
. Do not set the temperature lower than the
outside air temperature. Otherwise the
system may not work properly.
. Not recommended if windows fog up.
Dehumidified defrosting or defoggingGUID-6430F809-96AC-4582-A1F2-907A1F44D1CF1. Push the “” front defroster button. (The
indicator light on the button will come on.)
2. Operate the temperature control buttons (type A) or dial (type B) to set the desired
temperature. .
To quickly remove ice from the outside of the
windows, turn the “
” fan speed control
dial and set it to the maximum position.
. As soon as possible after the windshield is
clean, push the “AUTO” button to return to
the auto mode.
. When the “
” front defroster button is
pushed, the air conditioner will automatically
be turned on at outside temperatures above
238F (−58C) to defog the windshield, and
the air recirculate mode will automatically be
turned off.
Outside air is drawn into the passenger
compartment to improve the defogging
performance.
MANUAL OPERATIONGUID-DD9F85E6-993D-4D0F-AA81-0E42CFEE8E18
Fan speed controlGUID-A47CE066-351F-4CC8-AC17-7FC4FC991E14Turn the “” fan speed control dial to
manually control the fan speed.
Push the “AUTO” button to return to automatic
control of the fan speed.
Air recirculationGUID-2B823F0D-0272-430E-975F-993BF534048APush the intake air control button “” to
recirculate interior air inside the vehicle. The
indicator light “
” will come on.
The air recirculation mode cannot be activated
when the air conditioner is in the front defrosting mode “
”.
Outside air circulationGUID-E6DC013B-AF1A-40A2-93FA-8FF729A446D3Push the intake air control button “” to
change the air circulation from the intake air to
the outside air. The indicator light “
” will turn
off.
Automatic air intake controlGUID-8618E9EF-436B-4EE2-BD6B-EF915C7F0650In the AUTO mode, the intake air will be
controlled automatically. To manually control
the intake air, push the intake air control button
“
”. To return to the automatic control mode,
push the intake air control button “
” for
about 2 seconds. The indicator lights will flash
twice, and then the intake air will be controlled
automatically.
Air flow controlGUID-C19D08E9-C968-405F-8023-0A5995635CB9Pushing the “MODE” manual air flow control
button selects the air outlet to:
: Air flows from center and side ventilators.
: Air flows from center and side ventilators and foot outlets.
: Air flows mainly from foot outlets.
: Air flows from defroster and foot outlets.
Condition: