ECO mode NISSAN MURANO 2013 2.G Manual Online

Black plate (181,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
Be sure to follow the operating instructions, and
all the warnings and cautions in this section.
Improper operation of the top could cause
a system malfunction, damage, or dete-
rioration of the top material and related
parts.
SPA2873
WARNING
.Do not operate the top when there
is not enough clearance behind the
vehicle. Someone could become
trapped between the top storage
lid and another object (for example
a wall) which could result in serious
injury.
. Park the vehicle in a safe and level
place and apply the parking brake.
. Do not operate the top in a strong
wind. It could be blown by the wind,
striking someone or damaging the top.
. Do not allow anyone to stand up or
extend any portion of their body out
of the opening while the vehicle is in
motion or while the top is being
operated.
. In an accident you could be thrown
from the vehicle with an open top.
Always use seat belts and proper
child restraints.
Pre-driving checks and adjustments3-29
Condition:

Black plate (186,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-34Pre-driving checks and adjustments
fully opened or fully closed position.
When the soft top is operating, and any of the
following conditions occur, the top will stop
operating.
.When the selector lever is in the R (Reverse)
position.
. When the vehicle moves at a speed of 3
MPH (5 km/h) or more.
. When the battery voltage is extremely low.
. When the temperature of the soft top
system becomes extremely high.
Release the soft top operating switch, and push
the switch again to move the top to the fully
opened or closed position. The soft top indicator
light will turn off when the top operation is
completely finished.
If the soft top indicator light illuminates with the
ignition switch ON (whether the top is operated
or not, and when the top is engaged) , it may
indicate the top operating system is not
functioning properly. Have your vehicle checked
by a NISSAN dealer as soon as possible.AUTOMATIC WINDOW LOWERINGGUID-53158076-5049-419E-B46E-60FF9661FC5CWhen the soft top operating switch is pressed,
the power windows will automatically be low-
ered completely. The windows do not rise
automatically after the top operation is com-
pleted. Use the power window switches to raise
them.
SPA2632
OPENING THE TOPGUID-A212C8E0-E684-4914-9C6A-29123B5D454E1. Start the engine.
2. Push OPEN on the soft top operating switch and hold it until the top is fully opened.
.The soft top indicator light will illuminatewhile the top is in motion. (In about 20
seconds, the opening movement will
finish and the indicator light turns off.)
.Windows will automatically be fullyopened.
3. Release the switch when the top is fully opened. (The indicator light turns off.)
Condition:

Black plate (187,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
NOTE:
If you release the switch and press it again
while the top is being opened, the top will
slightly move to the closing direction, then
start moving to the opening direction
again. The top is designed to move in this
way. It is not a malfunction.
SPA2633
CLOSING THE TOPGUID-DAD80567-3F61-4CBF-86B1-D92B657E227A1. Start the engine.
2. Push CLOSE on the soft top operatingswitch and hold it until the top is fully closed.
.The soft top indicator light will illuminatewhile the top is in motion. (In about 20
seconds, the closing movement will
finish.)
.Windows will automatically be fullyopened.
3. Release the switch when the top is fully closed. (The indicator light will turn off.)
OPENING THE TOP USING THE IN-
TELLIGENT KEY
GUID-49044D36-3539-45EB-A570-6E07681CB5C9The soft top can be opened using the door
handle request switch.
Pre-driving checks and adjustments3-35
Condition:

Black plate (190,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-38Pre-driving checks and adjustments
IF THE TOP DOES NOT OPEN OR
CLOSE ELECTRICALLY
GUID-17B75AAD-7BCD-4553-9A36-FB3FA5E49CAFIf you cannot operate the soft top with the
operating switch, first check whether all the
following operating conditions are met.
.Vehicle is stopped
. Ignition switch is ON (Run the engine when
operating the top.)
. The trunk is closed
. The selector lever is in a position other than
the R (Reverse) position
. The luggage cover is pulled out and hooked
so that the roof storage area is separated
from the trunk.
If the top still does not move under the above
conditions or has any system malfunction, see a
NISSAN dealer as soon as possible. When you
must close the top by yourself, in the event of
emergency or when an immediate dealer service
is not available, close the top manually accord-
ing to the procedures shown in this section.
When closing the soft top manually:
. Move the vehicle to a safe place, away from
traffic.
. Two people should perform this procedure,
as some of the top parts are extremely
heavy.
The top cannot be opened manually.
WARNING
. Do not drive with the top partially
opened.
. If the top cannot be operated prop-
erly, see a NISSAN dealer as soon
as possible to have your vehicle
checked.
CAUTION
The storage lid is extremely heavy. The
storage lid should be manually opened
or closed by two people.
1. Open the trunk lid. In the event of a
discharged battery, the secondary trunk
release mechanism should be operated.
(See “Trunk lid (CrossCabriolet models)”
earlier in this section.)
2. Open the top storage lid.JVP0036X
a. Remove the trunk light*1.
b. Remove the lower trim clips
*3and
remove the upper and lower trim pieces
*2.
c. Remove the two luggage cover hooks
*4
on the left and right side of the trunk.
Then disconnect the connector
*5on
the left side luggage cover hook.
d. Remove the clips
*6behind the luggage
cover hooks.
Condition:

Black plate (198,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-46Pre-driving checks and adjustments
SPA2833
LOOSE FUEL CAP warningGUID-A04C09C8-3C53-423B-AC70-189E634F9E83The LOOSE FUEL CAP warning appears on the
dot matrix liquid crystal display when the fuel-
filler cap is not tightened correctly after the
vehicle has been refueled. It may take a few
driving trips for the message to be displayed. To
turn off the warning, perform the following steps:
1. Remove and install the fuel-filler cap as soonas possible. (See “Fuel-filler cap” earlier in
this section.)
2. Tighten the fuel-filler cap until a single click is heard.
3. Push the reset switch
*Aon the right side
of the combination meter for about 1 second to turn off the LOOSE FUEL CAP warning
after tightening the fuel cap.
GUID-24FBE4B2-4508-4AC7-A4F2-026DF692853E
WARNING
.
Do not adjust the steering wheel
while driving. You could lose control
of your vehicle and cause an acci-
dent.
. Do not adjust the steering wheel
any closer to you than is necessary
for proper steering operation and
comfort. The driver’s air bag inflates
with great force. If you are unrest-
rained, leaning forward, sitting side-
ways or out of position in any way,
you are at greater risk of injury or
death in a crash. You may also
receive serious or fatal injuries from
the air bag if you are up against it
when it inflates. Always sit back
against the seatback and as far
away as practical from the steering
wheel. Always use the seat belts.
TILT/TELESCOPIC STEERING
Condition:

Black plate (204,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-52Pre-driving checks and adjustments
Cancel or activate entry/exit functionGUID-58D4463D-3833-4D6F-AB39-9C380DA99AC9The selector lever must be in the P (Park)
position with the ignition switch in the OFF
position.
The entry/exit function can be activated or
canceled by pressing and holding the SET
switch for more than 10 seconds.
The indicator lights on the memory switches (1
and 2) will blink once when the function is
canceled, and the indicator lights will blink twice
when the function is activated. Note that the
indicator lights may illuminate after 5 seconds
while holding the SET switch. This indicates
readiness for linking the Intelligent Key to a
stored memory position. Keep the SET switch
pressed for more than 10 seconds to turn on or
off the entry/exit function.
The entry/exit function can also be activated or
canceled if the “Lift Steering Wheel on Exit” key
or “Slide Driver Seat Back on Exit” key is turned
to ON or OFF in the “Comfort” settings. (See
“Vehicle information and settings” in the “4.
Monitor, heater, air conditioner, audio, phone
and voice recognition systems” section.)
Initialize entry/exit functionGUID-3B7D11F0-51D7-4A5F-B078-9C3A3C24A746If the battery cable is disconnected, or if the fuse
opens, the entry/exit function will not work
though this function was set on before. In such
a case, after connecting the battery or replacing
with a new fuse, open and close the driver’s
door more than two times after the ignition
switch is placed in the LOCK position from the
ON position. The entry/exit function will be
activated.
SPA2756
MEMORY STORAGEGUID-1645D943-6DDE-4A8E-B347-C359AF16FEDFTwo positions for the driver’s seat, steering
column and outside mirrors can be stored in the
automatic drive positioner memory. Follow these
procedures to use the memory system.
1. Move the selector lever to the P (Park)position.
2. Push the ignition switch to the ON position.
3. Adjust the driver’s seat, steering column and outside mirrors to the desired positions by
manually operating each adjusting switch.
For additional information, see “Seats” in the
“1. Safety — Seats, seat belts and supple-
mental restraint system” section and “Tilt/
Condition:

Black plate (205,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
telescopic steering” earlier in this section
and “Outside mirrors” earlier in this section.
4. Push the SET switch and, within 5 seconds, push the memory switch (1 or 2) .
The indicator light for the pushed memory
switch will stay on for approximately 5
seconds after pushing the switch.
If memory is stored in the same memory
switch, the previous memory will be deleted.
Linking Intelligent Key to a stored mem-
ory position
GUID-83DABFB4-1BAC-4D52-AAD9-89B23BBFA840The Intelligent Key can be linked to a stored
memory position with the following procedure.
1. Follow one of the steps for storing a memory
position.
. While the indicator light for the memory
switch being set is illuminated for 5 sec-
onds, push the
button on the Intelligent
Key.
. Push the ignition switch to the OFF position,
and then push the SET switch. Push the
button while pushing the memory button
while the indicator light stays on for approxi-
mately 5 seconds.
If the indicator light blinks, the Intelligent Key is
linked to that memory setting.
Push the ignition switch to the OFF position, and then push the
button on the Intelligent Key.
The driver’s seat, steering wheel and outside
mirrors will move to the memorized position.
Confirming memory storageGUID-C42E9A63-7C42-464C-ABAE-3B9C731E9AA0. Push the ignition switch to the ON position
and push the SET switch. If the main
memory has not been stored, the indicator
light will come on for approximately 0.5
second. When the memory has stored in
position, the indicator light will stay on for
approximately 5 seconds.
. If the battery cable is disconnected, or if the
fuse opens, the memory will be canceled. In
this case, reset the desired position using
the previous procedure.
. If optional keys are added to your vehicle,
the memory storage procedure to switch 1
or 2 and linking Intelligent Key procedure to
a stored memory position should be per-
formed again for each Intelligent Key. For
additional Intelligent Key information, see
“Keys” earlier in this section.
Selecting the memorized positionGUID-1B13DD82-31E7-4920-83B1-6D7C94FBAB3E1. Move the selector lever to the P (Park)
position.
2. Use one of the following methods to move the driver’s seat, the outside mirrors and the
steering wheel.
.Push the ignition switch to the ONposition and push the memory switch (1
or 2) .
.Within 45 seconds of opening thedriver’s door, push the memory switch
(1 or 2) .
The driver’s seat, steering column and
outside mirrors will move to the memorized
position with the indicator light flashing, and
then the light will stay on for approximately 5
seconds.
SYSTEM OPERATIONGUID-6E092FC2-4164-461D-8930-0184862E613AThe automatic drive positioner system will not
work or will stop operating under the following
conditions:
. When the vehicle speed is above 4 MPH (7
km/h) (entry/exit function) .
. When the vehicle is driven (memory sto-
rage).
. When the adjusting switch for the driver’s
seat and steering column is turned on while
the automatic drive positioner is operating.
. When the seat, steering column and outside
mirrors have already been moved to the
memorized position.
. When no position is stored in the memory
switch.
Pre-driving checks and adjustments3-53
Condition:

Black plate (206,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-54Pre-driving checks and adjustments
.When the engine is started while moving the
automatic drive positioner.
. When the selector lever is moved from the P
(Park) position to any other position. (How-
ever, it will not be canceled while the seat
and steering column are returning to the
previous positions (entry/exit function).)
. When the driver’s door remains open for
more than 45 seconds and the ignition
switch is not in the ON position.
Condition:

Black plate (207,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
4 Monitor, heater, air conditioner, audio, phoneand voice recognition systems
Safety note ...
........................................................................\
.......... 4-3
Center multi-function control panel (models with color
display screen) ...
........................................................................\
.. 4-3
How to use multi-function controller ...
.............................. 4-5
How to use touch screen (models with
navigation system) ...
.............................................................. 4-5
Menu options (models with navigation system) ...
.......... 4-7
How to select menus on the screen ...
.............................. 4-8
Vehicle information and settings (if so equipped) ...
............ 4-9
How to use STATUS button ...
............................................. 4-9
How to use brightness control and display
ON/OFF button ...
................................................................... 4-9
How to use INFO button ...
.................................................. 4-9
How to use SETTING button ...
....................................... 4-13
RearView monitor (if so equipped) ...
................................... 4-23
How to read the displayed lines ...
.................................. 4-24
How to park with predictive course lines ...
.................. 4-24
Difference between predictive and
actual distances ...
................................................................ 4-26
Predictive course line settings ...
.................................... 4-28
How to adjust the screen ...
............................................. 4-28
Operating tips ...
................................................................... 4-29 Rear and rear-wide view monitor with Moving Object
Detection (MOD) (if so equipped)
...
................................... 4-30
How to switch the display ...
........................................... 4-31
How to park with predictive course lines ...
................ 4-33
How to adjust the screen ...
............................................ 4-37
Operating tips ...
................................................................. 4-37
Moving Object Detection (MOD) function ...
.............. 4-37
Ventilators ...
........................................................................\
........ 4-40
Heater and air conditioner ...
.................................................. 4-41
Automatic operation ...
...................................................... 4-43
Manual operation ...
............................................................ 4-44
To turn the system ON/OFF ...
....................................... 4-45
Operating tips ...
................................................................. 4-45
In-cabin microfilter ...
......................................................... 4-45
Servicing air conditioner ...
.............................................. 4-45
Audio system ...
........................................................................\
.. 4-46
Audio operation precautions ...
....................................... 4-46
FM-AM radio with Compact Disc (CD) changer ...
..... 4-61
FM-AM-SAT radio with Compact Disc
(CD) player ...
...................................................................... 4-66
DVD (Digital Versatile Disc) player operation
(models with navigation system) ...
................................ 4-70
Condition:

Black plate (208,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
USB memory operation (if so equipped)...
................... 4-73
Bluetooth®streaming audio (models with
navigation system) ...
........................................................... 4-77
iPod
®player operation (if so equipped) ...
.................... 4-82
Auxiliary input jacks (if so equipped) ...
.......................... 4-84
CD/DVD/USB memory care and cleaning ...
................ 4-85
Steering-wheel-mounted controls for audio
(if so equipped) ...
................................................................ 4-87
Antenna ...
........................................................................\
....... 4-88
Car phone or CB radio ...
........................................................ 4-89
Bluetooth
®Hands-Free Phone System (models with
navigation system) ...
................................................................. 4-89
Regulatory information ...
.................................................... 4-91
Voice commands ...
.............................................................. 4-91
Control buttons ...
................................................................. 4-91
Connecting procedure ...
.................................................... 4-92
Phone selection ...
................................................................ 4-92
Vehicle phonebook ...
.......................................................... 4-92
Making a call ...
..................................................................... 4-95
Receiving a call ...
................................................................. 4-96
During a call ...
...................................................................... 4-97
Phone setting ...
.................................................................... 4-97
Troubleshooting guide ...
..................................................... 4-99 Bluetooth
®Hands-Free Phone System (models
without navigation system) (if so equipped) ...
............... 4-100
Regulatory information ...
............................................... 4-101
Control buttons ...
............................................................ 4-102
Voice recognition system ...
.......................................... 4-102
Pairing procedure ...
....................................................... 4-106
Phonebook registration ...
.............................................. 4-107
Making a call ...
................................................................ 4-107
Receiving a call ...
........................................................... 4-108
During a call ...
................................................................. 4-108
Phone settings ...
............................................................. 4-109
Voice adaptation mode ...
.............................................. 4-112
NISSAN voice recognition system (models with
navigation system) ...
............................................................. 4-113
NISSAN voice recognition Standard Mode ...
......... 4-113
Using the system ...
........................................................ 4-116
NISSAN voice recognition Alternate
Command Mode ...
......................................................... 4-125
Using the system ...
........................................................ 4-134
Troubleshooting guide ...
............................................... 4-139
Condition: