fold seats NISSAN MURANO 2013 2.G Owners Manual

Black plate (29,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS1028
Lumbar support (if so equipped):GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The lumbar support feature provides lower back
support to the driver.
Push the front
*1or back*2end of the switch
to adjust the seatback lumbar area.
SSS1172
Front passenger’s seatback switch
SSS1175
Remote walk-in switch
Walk-in function (front passenger seat,
CrossCabriolet models):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
CAUTION
. When operating the walk-in func-
tion, be sure not to contact any
moving parts to avoid possible in-
juries and/or damages.
. When operating the walk-in func-
tion, be sure that the front passen-
ger seat is not occupied by a
passenger and/or any objects to
avoid possible injuries and/or da-
mages.
. After operating the walk-in function,
be sure to return the seat to the
rearmost position and then tilt up
the seatback until it latches.
This feature makes it easier to get in and out of
the rear seat. Use the following procedure when
getting in and out of the rear seat on the
passenger’s side. If the sun visor is used, close it
to the original position before operating the
walk-in feature.
1. Push the front passenger’s seatback switch to fold down the seatback and unlock the
seat position.
Safety — Seats, seat belts and supplemental restraint system1-7
Condition:

Black plate (30,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-8Safety — Seats, seat belts and supplemental restraint system
Alternatively, you can push the remote walk-
in switch located on the instrument panel to
fold down the front passenger’s seatback
and unlock the seat position.
2. Slide the seat forward to the foremost
position manually.
3. Get in or out the vehicle.
4. Return the front passenger seat to the
rearmost position. To slide the front passen-
ger seat, see “Manual seat adjustment”
earlier in this section.
SSS1173
Driver’s seatback release (CrossCabrio-
let models)
GUID-116F27BD-8437-47A9-8270-AD99D91FA75DTo exit the rear seat from the driver’s side, pull
the strap behind the driver’s seat to release the
driver’s seatback. The driver’s seatback will tilt
forward so that you can exit the vehicle.
NOTE:
Pulling the strap behind the driver’s seat
does not slide the driver’s seat forward.
You cannot slide the driver’s seat manu-
ally.
WARNING
Before using the driver’s seatback re-
lease, be sure that the driver’s seat is
not occupied by a driver and/or any
objects to avoid possible injuries and/
or damage.
Condition:

Black plate (31,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS0569
REAR SEATS (Hardtop models)GUID-42670C07-8DEA-4731-BDEC-1C3F2B7295A1
FoldingGUID-8333E9E4-6111-43A4-8DC3-B860D3C64DA7
Before folding the rear seats:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407.Secure the seat belts on the seat belt hooks
on the side wall. (See “Seat belt hooks
(Hardtop models)” later in this section.)
. Disconnect and stow the center seat belt
and tongue into the retractor base. (See
“Rear center seat belt (Hardtop models)”
later in this section.)
. Always reconnect the center seat belt when
the seat is returned to the upright position.
. Remove drink containers from the rear cup
holder. To fold down the seatbacks:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Pull the strap on the rear seat*A. Pull the lever
*Bbeside the cargo area and fold the seat-
back.
SSS0821
To return the seatbacks:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Manual operation:
Lift up each seatback and push it to the upright
position until it is latched.
Power operation (if so equipped):
Push and hold the corresponding switch located
on the lower side of the instrument panel
*Bor
the right or left side in the cargo area
*A.
A beep sounds once and the seatback will be
returned automatically.
A beep sounds twice when the seatback is fully
returned to the seating position.
If the control unit detects any obstacle or
malfunctions while in the power operation, a
Safety — Seats, seat belts and supplemental restraint system1-9
Condition:

Black plate (32,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-10Safety — Seats, seat belts and supplemental restraint system
beep sounds for 4 seconds and the seatback
will return to the folded position automatically.
Check if there are any obstacles caught that
prevent seats from returning to the folded
position. See a NISSAN dealer if the beep still
sounds.
CAUTION
When operating the rear power seat-
back return, make sure that the vehicle
is stopped and the transmission is in
the P (Park) position.
WARNING
.Never allow anyone to ride in the
cargo area or on the rear seats
when they are in the fold-down
position. In a collision, people riding
in these areas are more likely to be
seriously injured or killed.
. Do not allow people to ride in any
area of your vehicle that is not
equipped with seats and seat belts.
Be sure everyone in your vehicle is
in a seat and using a seat belt
properly. .
Do not fold down the rear seats
when occupants are in the rear seat
area or any luggage is on the rear
seats.
. When folding or returning the seat-
backs to the upright position, to
avoid injury to yourself and others:
— Make sure that the seat path is
clear before moving the seat.
— Be careful not to allow hands or feet to get caught or pinched in
the seat.
. Properly secure all cargo to help
prevent it from sliding or shifting.
Do not place cargo higher than the
seatbacks. In a sudden stop or
collision, unsecured cargo could
cause personal injury.
. When returning the seatbacks, be
sure to attach the rear center seat
belt connector.
. Do not unfasten the rear center seat
belt connector except when folding
down the rear seat.
. When attaching the rear center seat
belt connector, be certain that the
seatbacks are completely secured in
the latched position and the rear center seat belt connector is com-
pletely secured.
. If the rear center seat belt connector
and the seatbacks are not secured
in the correct position, serious per-
sonal injury may result in an acci-
dent or sudden stop.
Condition:

Black plate (43,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSS1181
Seat belt guide (front seats, CrossCab-
riolet models)
GUID-3EF9ED5F-135A-43B1-8954-CAD684674E27When the seat belt guide is used with the front
seat, the seat belt can easily be pulled out.
Release the seat belt guide, clip the seat belt
and install the seat belt guide again.
When using the seat belt guide, do not allow it
to twist.
WARNING
When using the seat belt guide, make
sure that the seat belt guide is securely
installed to the seat. Otherwise, theseat belt may slip and result in personal
injury.
CAUTION
.
When entering or exiting the rear
seat, or inserting or retrieving lug-
gage with the seatback folded
down, always release the seat belt
guide. Otherwise, the seat belt
guide may be damaged.
. Do not fold the seat forward or pull
it backward by holding the seat belt
guide in your hand. Doing so may
damage the seat belt guide.
SSS0351A
Shoulder belt height adjustment (Hard-
top models)
GUID-E8DCDEEB-44E6-4A0A-B2D9-EB6DBF18146CThe shoulder belt anchor height should be
adjusted to the position best for you. (See
“Precautions on seat belt usage” earlier in this
section.)
To adjust, pull the adjustment button
*1, and
then move the shoulder belt anchor to the
desired position
*2, so that the belt passes
over the center of the shoulder. The belt should
be away from your face and neck, but not falling
off of your shoulder. Release the adjustment
button to lock the shoulder belt anchor into
position.
Safety — Seats, seat belts and supplemental restraint system1-21
Condition:

Black plate (44,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-22Safety — Seats, seat belts and supplemental restraint system
WARNING
.After adjustment, release the ad-
justment button and try to move the
shoulder belt anchor up and down
to make sure it is securely fixed in
position.
. The shoulder belt anchor height
should be adjusted to the position
best for you. Failure to do so may
reduce the effectiveness of the
entire restraint system and increase
the chance or severity of injury in an
accident.
SSS0845
Seat belt hooks (Hardtop models)GUID-0F6C8515-923F-4DA4-BED8-81B474353BA2When the rear seat belts are not in use and
when folding down the rear seats, hook the rear
outer seat belts on the seat belt hooks.
SSS0846
Rear center seat belt (Hardtop models)GUID-D2977525-73CC-440E-AC17-490B6791BECAThe rear center seat belt has a connector tongue
*1and a seat belt tongue*2. Both the
connector tongue and the seat belt tongue must
be securely latched for proper seat belt opera-
tion.
Condition:

Black plate (46,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-24Safety — Seats, seat belts and supplemental restraint system
Stowing rear center seat belt:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407When folding down the rear seat, the rear center
seat belt can be retracted into a stowed position
as follows:
1. Hold the connector tongue
*1so that the
seat belt does not retract suddenly when the
tongue is released from the connector
buckle. Release the connector tongue by
inserting a suitable tool such as key
*Ainto
the connector buckle.
2. Insert the seat belt tongue into the retractor base first
*2.
3. Then secure the connector tongue into the retractor base
*3.
WARNING
.Do not unfasten the rear center seat
belt connector except when folding
down the rear seat.
. When attaching the rear center seat
belt connector, be certain that the
seatbacks are completely secured in
the latched position and the rear
center seat belt connector is com-
pletely secured.
. If the rear center seat belt connector
and the seatbacks are not secured in the correct position, serious per-
sonal injury may result in an acci-
dent or sudden stop.
SSS0232
Condition:

Black plate (47,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
Attaching rear center seat belt:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Always be sure the rear center seat belt
connector tongue and connector buckle are
attached. Disconnect only when folding down
the rear seat.
To connect the buckle:
1.Pull out the connector tongue from the
retractor base
*1.
2. Pull out the seat belt tongue from the
retractor base
*2.
3. Pull the seat belt and secure the connector buckle until it clicks
*3.
The center seat belt connector tongue and
buckle are indicated by the !and ~mark.
The center seat belt connector tongue can be
attached only into the rear center seat belt
connector buckle.
To fasten the seat belt, see “Fastening the seat
belts” earlier in this section.
WARNING
. Do not unfasten the rear center seat
belt connector except when folding
down the rear seat.
. When attaching the rear center seat
belt connector, be certain that the seatbacks are completely secured in
the latched position and the rear
center seat belt connector is com-
pletely secured.
. If the rear center seat belt connector
and the seatbacks are not secured
in the correct position, serious per-
sonal injury may result in an acci-
dent or sudden stop.
SSS0235
Storing rear seat belt buckles (Hardtop
models)
GUID-34BA1AAF-B284-4222-A05C-7E212FF3C674Before folding down the seat, put the buckles in
the storage of the seat cushion to avoid
dropping it under the seat cushion.
SEAT BELT EXTENDERSGUID-798C755D-7740-4606-AB38-FAC398986CFAIf, because of body size or driving position, it is
not possible to properly fit the lap-shoulder belt
and fasten it, an extender that is compatible with
the installed seat belts is available that can be
purchased. The extender adds approximately 8
in (200 mm) of length and may be used for either
the driver or front passenger seating position.
See a NISSAN dealer for assistance with
Safety — Seats, seat belts and supplemental restraint system1-25
Condition: