reset NISSAN MURANO 2013 2.G Owners Manual

Black plate (16,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
0-10Illustrated table of contents
GUID-32B6101A-1F0F-4AD4-AF3B-40C2CE7B8097
JVO0067X
1. Heated steering wheel switch* (P.2-41)
2. Power lift gate switch* (Hardtop models)(P.3-20) or trunk lid release switch (Cross-
Cabriolet models) (P.3-25)
3. Warning systems switch* (P.2-43) — Lane Departure Warning (LDW) system*
(P.5-20) — Blind Spot Warning (BSW) system* (P.5-20)
4. Instrument brightness control switch (P.2-40)
5. Headlight, fog light and turn signal switch — Headlight (P.2-37)
— Turn signal light (P.2-40)
— Fog light* (P.2-41)
6. Trip computer switch (P.2-25) 7. TRIP/RESET switch (P.2-6)
8. Wiper and washer switch (P.2-32)
9. Vehicle Dynamic Control (VDC) off switch (P.
2-44, P.5-39)
10. Power lift gate main switch* (Hardtop models) (P.3-20) or All-Wheel Drive (AWD) LOCK
switch (CrossCabriolet models) (P.5-33)
11. Power rear seatback switch* (Hardtop models) (P.1-9)
12. Power rear seatback switch* (Hardtop models) (P.1-9) or Remote walk-in switch (CrossCabrio-
let models) (P.1-7)
13. Fuel-filler door opener switch (P.3-44)
14. Manual tilting/telescopic steering wheel lever* (P.3-47)
15. Electric tilting/telescopic steering wheel switch* (P.3-47)
16. Steering-wheel-mounted controls (left side)* — Audio control* (P.4-87)
— Bluetooth
®Hands-Free Phone System con-
trol (models with navigation system)* (P.4-89)
— Bluetooth
®Hands-Free Phone System con-
trol (models without navigation system)*
(P.4-100)
17. Steering wheel — Horn (P.2-41)
— Driver supplemental air bag (P.1-45)
— Power steering system (P.5-37)
18. Steering-wheel-mounted controls (right side) — Cruise control switches (P.5-30)
19. Center-console mounted controls
COCKPIT
Condition:

Black plate (19,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
GUID-8035B36E-5604-4EA6-AA6B-CA8C0BC1732D
JVO0043X
1. Instrument brightness control switch (P.2-40)
2. Tachometer (P.2-7)
3. Speedometer (P.2-6)
4. Fuel gauge (P.2-8)
5. Warning/indicator lights (P.2-11)
6. Trip computer switch (P.2-25)
7. Dot matrix liquid crystal display (P.2-20)— Trip computer (P.2-40)
8. Engine coolant temperature gauge (P.2-7)
9. Odometer/twin trip odometer (P.2-6)/Continu- ously Variable Transmission (CVT) position
indicator (P.2-17)
10. RESET switch for trip odometer (P.2-6)
Illustrated table of contents0-13
METERS AND GAUGES
Condition:

Black plate (26,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
1-4Safety — Seats, seat belts and supplemental restraint system
SSS0793
Seat lifter (if so equipped):GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Pull up or push down the adjusting lever to
adjust the seat height until the desired position
is achieved.
SSS0684
Lumbar support (if so equipped):GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The lumbar support feature provides lower back
support to the driver.
Move the lever
*1up or down to adjust the
seatback lumbar area.
Power seat adjustmentGUID-2155E48C-B77E-4502-84B7-2AF110D60DE4
Operating tips:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407. The power seat motor has an auto-reset
overload protection circuit. If the motor
stops during operation, wait 30 seconds,
then reactivate the switch.
. Do not operate the power seat switch for a
long period of time when the engine is off.
This will discharge the battery.
See “Automatic drive positioner” in the “3. Pre-
driving checks and adjustments” section for the
seat position memory function (if so equipped).
Condition:

Black plate (87,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
GUID-06B56D4D-A0AA-4178-A121-A31F959AC846
JVO0067X
1. Heated steering wheel switch*
2. Power lift gate switch* (Hardtop models) ortrunk lid release switch (CrossCabriolet models)
3. Warning systems switch* - Lane Departure Warning (LDW) system*
- Blind Spot Warning (BSW) system*
4. Instrument brightness control switch 5. Headlight, fog light and turn signal switch
— Headlight
— Turn signal light
— Fog light*
6. Trip computer switch
7. TRIP/RESET switch
8. Wiper and washer switch 9. Vehicle Dynamic Control (VDC) off switch
10. Power lift gate main switch* (Hardtop models) or
All-Wheel Drive (AWD) LOCK switch (Cross-
Cabriolet models)
11. Power rear seatback switch* (Hardtop models)
12. Power rear seatback switch* (Hardtop models) or Remote walk-in switch (CrossCabriolet mod-
els)
13. Fuel-filler door opener switch
14. Manual tilting/telescopic steering wheel lever*
15. Electric tilting/telescopic steering wheel switch*
16. Steering-wheel-mounted controls (left side)* — Audio control*
— Bluetooth
®Hands-Free Phone System con-
trol (models with navigation system)*
— Bluetooth
®Hands-Free Phone System con-
trol (models without navigation system)*
17. Steering wheel — Horn
— Driver supplemental air bag
— Power steering system
18. Steering-wheel-mounted controls (right side) — Cruise control switches
19. Center-console mounted controls — Heated seat switches*
— All-Wheel Drive (AWD) LOCK switch*
(Hardtop models)
— Soft top operating switch (CrossCabriolet
models)
*: if so equipped
Instruments and controls2-3
COCKPIT
Condition:

Black plate (89,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
GUID-A68BAE6F-B6C6-458C-9E0C-28DA5D3B2890
JVO0043X
1. Instrument brightness control switch
2. Tachometer
3. Speedometer
4. Fuel gauge
5. Warning/indicator lights
6. Trip computer switch
7. Dot matrix liquid crystal display— Trip computer
8. Engine coolant temperature gauge
9. Odometer/twin trip odometer/Continuously Vari- able Transmission (CVT) position indicator
10. RESET switch for trip odometer
The needle indicators may move slightly
after the ignition switch is pushed to the LOCK position. This is not a malfunction.
Instruments and controls2-5
METERS AND GAUGES
Condition:

Black plate (90,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-6Instruments and controls
JVI0252X
Speedometer
SPEEDOMETER AND ODOMETERGUID-A5312850-B162-4691-B245-BFE52CFF92CD
SpeedometerGUID-6D108D90-F044-4A12-A5A1-80A313264F81The speedometer indicates vehicle speed in
miles per hour (MPH) and kilometers per hour
(km/h) .
SIC4699
Odometer/twin trip odometer
Odometer/twin trip odometerGUID-8971DF72-32A1-467A-9B68-200871A5DCCCThe odometer*1and twin trip odometer*2
are displayed when the ignition switch is in the
ON position.
The odometer records the total distance the
vehicle has been driven.
The twin trip odometer records the distance of
individual trips.
Changing the display:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Pushing the TRIP RESET switch*3on the right
side of the combination meter panel changes
the display as follows:
TRIP A ?TRIP B ?TRIP A Resetting the trip odometer:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Pushing the TRIP RESET switch*3for more
than 1 second resets the trip odometer to zero.
Condition:

Black plate (99,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
position as long as the low tire pressure warning
light remains illuminated.
For additional information, see “Dot matrix liquid
crystal display” later in this section, “Tire
Pressure Monitoring System (TPMS)” in the “5.
Starting and driving” section and “Tire Pressure
Monitoring System (TPMS)” in the “6. In case of
emergency” section.
TPMS malfunction:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407If the TPMS is not functioning properly, the low
tire pressure warning light will flash for approxi-
mately 1 minute when the ignition switch is
pushed ON. The light will remain on after the 1
minute. Have the system checked by a NISSAN
dealer. The CHECK TIRE PRESSURE warning
does not appear if the low tire pressure warning
light illuminates to indicate a TPMS malfunction.
For additional information, see “Tire Pressure
Monitoring System (TPMS)” in the “5. Starting
and driving” section. For the CHECK TIRE
PRESSURE warning, see “Dot matrix liquid
crystal display” later in this section.
WARNING
.If the light does not illuminate with
the ignition switch pushed ON, have
the vehicle checked by a NISSAN dealer as soon as possible.
. If the light illuminates while driving,
avoid sudden steering maneuvers or
abrupt braking, reduce vehicle
speed, pull off the road to a safe
location and stop the vehicle as
soon as possible. Driving with un-
der-inflated tires may permanently
damage the tires and increase the
likelihood of tire failure. Serious
vehicle damage could occur and
may lead to an accident and could
result in serious personal injury.
Check the tire pressure for all four
tires. Adjust the tire pressure to the
recommended COLD tire pressure
shown on the Tire and Loading
Information label to turn the low
tire pressure warning light OFF. If
the light still illuminates while driv-
ing after adjusting the tire pressure,
a tire may be flat. If you have a flat
tire, replace it with a spare tire as
soon as possible.
. When a spare tire is mounted or a
wheel is replaced, the TPMS will not
function and the low tire pressure
warning light will flash for approxi-
mately 1 minute. The light will remain on after 1 minute. Contact
your NISSAN dealer as soon as
possible for tire replacement and/
or system resetting.
. Replacing tires with those not ori-
ginally specified by NISSAN could
affect the proper operation of the
TPMS.
CAUTION
.The TPMS is not a substitute for the
regular tire pressure check. Be sure
to check the tire pressure regularly.
. If the vehicle is being driven at
speeds of less than 16 MPH (25
km/h) , the TPMS may not operate
correctly.
. Be sure to correctly install the
specified size of tires to the four
wheels.
Instruments and controls2-15
Condition:

Black plate (108,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-24Instruments and controls
SIC4237
MAINTENANCE INDICATORSGUID-0A851647-6BB2-4E92-AEB5-E04319FCA2E4
1. Engine oil replacement indicatorGUID-9CEF8B90-48A9-4FB5-BFD9-0CF43586EC4FThis indicator appears when the customer set
time comes for changing the engine oil. You can
set or reset the distance for changing the engine
oil. (See “Trip computer” later in this section.)
2. Oil filter replacement indicatorGUID-C344252D-B1CB-46F2-AEAD-7C37EC262221This indicator appears when the customer set
time comes for replacing the oil filter. You can
set or reset the distance for replacing the oil
filter. (See “Trip computer” later in this section.)
3. Tire replacement indicatorGUID-1A74526D-9B7C-43A3-95CF-62EFC05FBC61This indicator appears when the customer set
distance comes for replacing tires. You can set
or reset the distance for replacing tires. (See
“Trip computer” later in this section.)
WARNING
The tire replacement indicator is not a
substitute for regular tire checks, in-
cluding tire pressure checks. See
“Changing wheels and tires” in the “8.
Maintenance and do-it-yourself” sec-
tion. Many factors including tire infla-
tion, alignment, driving habits and road
conditions affect tire wear and whentires should be replaced. Setting the
tire replacement indicator for a certain
driving distance does not mean your
tires will last that long. Use the tire
replacement indicator as a guide only
and always perform regular tire checks.
Failure to perform regular tire checks,
including tire pressure checks could
result in tire failure. Serious vehicle
damage could occur and may lead to a
collision, which could result in serious
personal injury or death.
4. “OTHER” indicatorGUID-17015DA7-2755-4CAC-AF46-619CAF47DE9DThis indicator appears when the customer set
time comes for replacing items other than the
engine oil, oil filter and tires. You can set or reset
the distance for replacing the items. (See “Trip
computer” later in this section.)
More maintenance reminders are also available
on the center display (if so equipped). (See
“How to use INFO button” in the “4. Monitor,
heater, air conditioner, audio, phone and voice
recognition systems” section.)
Condition:

Black plate (110,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-26Instruments and controls
SIC3674
Average fuel consumption (MPG, l/100
km) and speed (MPH or km/h)
GUID-5567CAAC-37CB-49C0-8903-54489EC24183
Fuel consumption:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The average fuel consumption mode shows the
average fuel consumption since the last reset.
Resetting is done by pushing the
switch*B
for longer than 1 second. (The average speed is
also reset at the same time.)
The display is updated every 30 seconds. At
about the first 1/3 mile (500 m) after a reset, the
display shows “——”.
Speed:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The average speed mode shows the average
vehicle speed since the last reset. Resetting isdone by pushing the
switch*Bfor longer
than 1 second. (The average fuel consumption is
also reset at the same time.)
The display is updated every 30 seconds. The
first 30 seconds after a reset, the display shows
“——”.
SIC4701
Elapsed time and trip odometer (miles or
km)
GUID-FEA80D52-9DA7-4A2D-BD49-7619EBBECCF9
Elapsed time:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The elapsed time mode shows the time since
the last reset. The displayed time can be reset
by pushing the
switch*Bfor longer than 1
second. (The trip odometer is also reset at the
same time.)
Trip odometer:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The trip odometer mode shows the total
distance the vehicle has been driven since the
last reset. Resetting is done by pushing the
switch*Bfor longer than 1 second. (The
elapsed time is also reset at the same time.)
Condition:

Black plate (112,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-28Instruments and controls
SIC3678
SettingGUID-180A1674-9E9A-45F6-9ECF-354F636CDD00Setting cannot be made while driving. A
message “Setting can only be operated
when stopped” is also displayed on the dot
matrix crystal display.
The
switch*Aandswitch*Bare
used in the setting mode to select and decide a
menu.
SKIP:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Push theswitch*Ato move to the warning
check mode.
Push the
switch*Bto select other menus. ALERT:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Alert menu can be set to notify the following
items.
.
TIMER
Select this submenu to specify when the
“TIMER” indicator activates.
. ICY
Select this submenu to display the low
outside temperature warning.
To return to the top page of the setting mode,
select “BACK”.
MAINTENANCE:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The maintenance intervals of the following items
can be set or reset for the reminders.
. OIL
Select this submenu to set or reset the
distance for changing the engine oil.
. FILTER
Select this submenu to set or reset the
distance for replacing the oil filter.
. TIRE
Select this submenu to set or reset the
distance for replacing tires.
. OTHER
Select this submenu and set or reset the
distance for replacing items other than the
engine oil, oil filter and tires. To return to the top page of the setting mode,
select “BACK”.
OPTIONS:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The following option menus can be set to your
preference.
.
LANGUAGE
Select this submenu to choose English,
French or Spanish for display.
. UNIT
Select this submenu to choose the unit from
MPG or l/100 km.
. EFFECTS
Select this menu to set the dial effects
described below to on or off.
— The indicator needles sweep in the
meters and the ring illumination will be
brightened gradually when the engine is
started.
To return to the top page of the setting mode,
select “BACK”.
Condition: