parking brake NISSAN MURANO 2013 2.G Quick Reference Guide

FRONT SEAT ADJUSTMENTS
MANUAL SEATS (if so equipped)

To slide the seat forward or backward, pull up on
the lever
01 under the front of the seat and slide
forward or backward. Release the lever to lock the
seat in position.

To adjust your seatback forward or backward, lift the
lever
02 on the side of the seat.

Release the lever when you have found a comfortable
angle and the seat belt fi ts properly.
SEAT LI FTE R (if so equipped)

To adjust the seat height, pull up or push down on
the adjusting lever
03 repeatedly.
LUMBAR SUPPORT (if so equipped)

Your driver’s seat lumbar support 04 is located on
the inboard side of the driver’s front seat.

Adjust by moving the lever up or down.
8
first drive features
SOFT TOP OPERATION (CrossCabriolet models)
The soft top can be operated only when the trunk is
separated by the luggage cover. The luggage cover must
be pulled out and hung on both hooks or the top will not
operate. Before opening or closing your soft top, refer to
the Owner’s Manual for detailed warnings and cautions
regarding soft top operation.
Soft Top Operation
1. Make sure the area around the vehicle is clear of obstructions and that \
there is more
than 10 feet (3 m) of clearance from the ground and more than 4.9 feet (1.5 m) of\

clearance from the rear of the vehicle.
2. Pull out the luggage cover and hang on both hooks
01 .
3. Apply the parking brake and move the shift lever to the P (PARK) position.
4. Depress the brake pedal.
5. Start the engine.
6. Push and hold the soft top operating switch, located
on the center console, to OPEN
02 or CLOSE
03
until the top is fully opened or closed.
For more information, refer to the “Instruments and controls (section 2)”
and the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
02
03
01
01
0203
04
P




S

L

F
O
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.

HEADLIGHT CONTROL SWITCH
HEADLIGHT CONTROL

Turn the headlight control switch to the
position

01 to turn on the front parking, side
marker, tail, license plate and instrument panel
lights. Turn the switch to the
position
02 to
turn on the headlights.
AUTOLIGHT SYSTEM (if so equipped)

The autolight system will automatically turn the headlights on when it is\
dark and off when it
is light. The system will keep the headlights on for a period of time after you tur\
n the ignition
off and all doors are closed.

To activate the autolight system, turn the headlight control switch to the AUTO position
03
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight
control switch to the OFF,
01 or
position
02 .
HIGH BEAM SELECT

Push the headlight control switch forward 04 to
select the high beam function. The blue indicator
light
illuminates in the instrument panel. Pull
the headlight switch back to the original position to
select the low beam. The blue indicator light goes off.

Pull and release the headlight control switch 05 to
fl ash the headlight high beams on and off.
12
first drive features
01
03
02
STARTING/STOPPING THE EN GINE
Depress the brake pedal.

Press the ignition switch START/STOP button to
start the engine.
NOTE: It is important to make sure the NISSAN Intelligent
Key
® is with you (that is, in your pocket or purse).
TURNING THE ENGINE OFF

Move the shift lever to the P (PARK) position and
apply the parking brake.

Press the ignition switch START/STOP button to
turn the engine off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
04
05
W
















s




To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.