display NISSAN MURANO 2014 2.G Quick Reference Guide

INSTRUMENT BRIGHTNESS CONTROL SWITCH*
TWIN TRIP ODOMETER SWITCHES*
HEADLIGHT AND TURN SIGNAL CONTROL
LOW TIRE PRESSURE WARNING LIGHT
VEHICLE INFORMATION DISPLAY
WINDSHIELD WIPER AND WASHER SWITCH STEERING WHEEL SWITCHES FOR
AUDIO* / BLUETOOTH
® / NAVIGATION
CRUISE CONTROL
TRUNK LID / LIFTGATE RELEASE SWITCH
FUEL-FILLER DOOR RELEASE SWITCH
INTELLIGENT KEY
® PORT VEHICLE DYNAMIC CONTROL (VDC)
OFF SWITCH*
ALL-WHEEL DRIVE (AWD) LOCK SWITCH*
REMOTE WALK-IN SWITCH
TILT / TELESCOPIC STEERING COLUMN*
HOOD RELEASE*
CONTROL PANEL DISPLAY* PUSH-BUTTON IGNITION SWITCH
AU D I O SYSTE M
AUTOMATIC CLIMATE CONTROLS
FRONT PASSENGER AIR BAG
STATUS LIGHT*
SOFT TOP OPENER SWITCH
*See your Owner’s Manual for information.010203040506
09
15
0710
1617
1819202122
0811
131214
1920
16
12
1014
09
02
05
0611
18
08
0301
04
15
13
07
17
21
22
Behind
steering wheel
Behind
steering wheel
1591421_14d_Murano_QRG_012714b.indd 31/27/14 3:11 PM

2
NEW SYSTEM FEATURES
HEATED STEERING WHEEL (if so equipped)
Once activated, your heated steering wheel
will automatically turn on and off to maintain a
temperature above 68°F (20°C).

When the surface temperature of the steering wheel
is above 68°F (20°C) and the control switch

01 is
turned on, the system will not heat the steering wheel. This does not indicate a malfunction.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
01
MOVING OBJECT DETECTION (MOD) (if so equipped)
If the MOD system detects moving objects while in rearview, a yellow frame
01 will be
displayed on the camera image and a chime will sound.

To temporarily disable the MOD function, follow this procedure:
1. Start with the vehicle in the P (PA R K ) position.
2. On the vehicle information display, push the
SETTING button.
3. Select DRIVER ASSISTANCE and push ENTER.
4. Select MOVING OBJECT DETECTION ( MOD)
and press ENTER.

When the following are displayed:
• Blue MOD

02 icon; the system is operative in this view.
• Gray MOD
02 icon; the system is not operative in this view.
• No MOD icon; the system is off.
For more information, refer to the “Monitor, heater, air conditioner, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual.
02
01
BLIND SPOT WARNING (BSW) SYSTEM (if so equipped)
The Blind Spot Warning (BSW) system alerts the
driver when another vehicle moves into the vehicle’s
blind spot area.

An indicator light near the driver’s outside mirror will
illuminate if the radar sensors detect a vehicle in the
detection zone.

The indicator light will first illuminate in orange and then turn green\
while
the system is on. This indicates that the Blind Spot Warning (BSW)
system is operational.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
1591421_14d_Murano_QRG_012714b.indd 21/27/14 3:11 PM
To view detailed instructional videos regarding features in this Quick Reference Guide, please go to www.nissanownersinfo.mobi.

3
LANE DEPARTURE WARNING (LDW) SYSTEM (if so equipped)
The LANE DEPARTURE WARNING ( LDW) system alerts the driver
when the vehicle moves close to either the left or the right of a clearl\
y
marked traveling lane.

When the vehicle approaches either the left or right of the clearly marked
traveling lane, a chime will sound and the LDW light
01 (orange) on the
instrument panel will blink.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
01
REARVIEW MONITOR (if so equipped)
When the shift lever is shifted into the R (REVERSE)
position, the monitor display shows a rearward view
from the vehicle.

The colored guide lines on the display screen indicate
vehicle width and approximate distances to objects
with reference to the vehicle body line:
• Red 1.5 ft (0.5 m); Yellow 3 ft (1 m); Green 7 ft
(2 m) and 10 ft (3 m).
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4)” of your
Owner’s Manual.
1591421_14d_Murano_QRG_012714b.indd 31/27/14 3:11 PM
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.

4
FUEL-FILLER DOOR
To open the fuel-filler door, push the opener switch 01, located on the instrument panel to the left of the
steering wheel.

The fuel-filler door is located on the driver’s side of
the vehicle.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
01
ESSE NTIAL I N FOR MATION
TIRE PRESSURE MONITORING SYSTEM (TPMS)
A CHECK TIRE PRESSURE warning
message will appear in the vehicle information
display
01 and the low tire pressure warning
light 02 will illuminate when one or more tires
are low on pressure and air is needed.
• The tire pressures should be checked when
the tires are cold. The tires are considered cold after the vehicle has
been parked for 3 hours or more or driven less than 1 mile (1.6 km)
at moderate speeds.

After tire pressures are adjusted, drive the vehicle at speeds above 16 \
MPH (25 km/h). The
CHECK TIRE PRESSURE warning message and low tire pressure warning light will disappear.

When the low tire pressure warning light flashes for 1 minute and then \
remains on, the TPMS
is not functioning properly. Have the system checked by a NISSAN dealer.

Tire pressure rises and falls depending on the heat caused by the vehicle\
’s operation and the
outside temperature. Low outside temperature can lower the temperature o\
f the air inside
the tire, which can cause a lower tire inflation pressure. This may cause the low tire pressure
warning light to illuminate. If the warning light illuminates, check the tire pressure in your tires.
• Check the tire pressure (including the spare tire) often and always prior \
to long distance trips.

The Tire and Loading Information label contains valuable information. Please refer to section 9,
“Technical and consumer information”, in your Owner’s Manual for the location of the Tire and
Loading Information label.
For more information, refer to the “Instruments and controls (section 2)” , the “Starting and driving (section 5)” and the
“Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
01
02
LOOSE FUEL CAP
A LOOSE FUEL CAP warning message will appear
in the vehicle information display 01 when the fuel-
filler cap is not tightened correctly.

To tighten, turn the cap clockwise until a single click
is heard.

The warning message will disappear when the vehicle detects the fuel-
filler cap is properly tightened and the reset button
02 is pressed.
If the cap is not properly tightened, the Malfunction Indicator Light

may illuminate.
For more information, refer to the “Instruments and controls (section 2)” and the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
01
02
1591421_14d_Murano_QRG_012714b.indd 41/27/14 3:11 PM
To view detailed instructional videos regarding features in this Quick Reference Guide, please go to www.nissanownersinfo.mobi.

5
AUTOMATIC POWER WINDOWS
(CrossCabriolet models)
Your power windows have an automatic adjusting
function to ensure windows close completely to help
seal against wind noise and weather leaks.

When the front doors are opened, the windows
automatically lower slightly to avoid contact between
the windows and the side roof panels.

If your vehicle’s battery has been discharged or disconnected, the power window automatic
adjusting function will not operate.

Refer to your Owner’s Manual for information on how to initialize your power window system.

If the power window functions do not operate properly after initializing\
the system, have your
vehicle checked by a NISSAN dealer.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
TOWING YOUR VEHICLE
ALL-WHEEL DRIVE (AWD) VEHICLE

An all-wheel drive vehicle must be towed with all wheels off the ground.\


For proper towing and to avoid accidental damage to your vehicle, NISSAN recommends that
a service operator tow your vehicle after carefully reading the Owner’s Manual precautions.
For more information, refer to the “In case of emergency (section 6)” of your Owner’s Manual.
CLOCK SET/ADJUSTMENT
To adjust the time and the appearance of the clock
on the display:
1. Press the SETTING button on the control panel.
2. Touch the Others key.
3. Touch the Clock key.

The following settings can be adjusted:
• On-screen Clock: The clock in the upper right
corner of the display can be turned ON or OFF.
• Clock Format (24h): The clock can be set to 12 hours or 24 hours.
• Offset (hour): The time can be adjusted by increasing or decreasing per hour.
• Offset (min): The time can be adjusted by increasing or decreasing per minute.
• Daylight Savings Time: The application of daylight savings time can be turned ON or OFF.
• Time Zone: Adjust the time zone. Choose a time zone from the available list.

Press the BACK button to return to the previous screen.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4)” of
your Owner’s Manual.
1591421_14d_Murano_QRG_012714b.indd 51/27/14 3:11 PM
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.

6
NISSAN INTELLIGENT KEY® SYSTE M
The NISSAN Intelligent Key® system allows you to lock
or unlock your vehicle, open your trunk lid and start the
engine. It is important to make sure the Intelligent Key is
with you (that is, in your pocket or purse).

The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.

To lock the vehicle, push either door handle
request switch
01 once or press the
button
02 on the key fob.

To unlock the vehicle, perform one of the
following procedures:
• Push either door handle request switch
01 once;
the corresponding door will unlock. Push the door
handle request switch
01 again within 1 minute; all
other doors will unlock, or
• Press the

button 03 on the key fob to unlock the
driver’s side door. Press the button again; all other doors will unlock.

The Intelligent Key can also be used to activate the panic alarm by pressing and holding \
the

button 04 for more than 1 second. Once activated, the panic alarm and headlights w\
ill stay on
for a period of time.
NISSAN INTELLIGENT KEY
® BATTERY DISCHARGE

If the battery in the Intelligent Key is almost discharged,
the guide light

05 of the Intelligent Key port blinks, and
the key battery discharge indicator 06 is displayed in
the vehicle information display.

To start the engine under these circumstances, insert
the Intelligent Key into the key port with the buttons
facing upward and the key ring end toward you until
it latches into place. Then push the ignition switch to
start the engine.

To remove the Intelligent Key from the port, push the
ignition switch to turn the engine off and then pull the
Intelligent Key out of the port.

The Intelligent Key port does not charge the Intelligent
Key battery. If you see the key battery discharge
indicator

06, replace the battery in the Intelligent Key.

Do not insert the mechanical key or other objects into the key port because they will damage
the key port.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” , the “Starting and driving (section
5)” and the “Maintenance and do-it yourself (section 8)” of your Owner’s Manual.
FIRST DRIVE FEATURES
F
02
03
04
01
06
05
1591421_14d_Murano_QRG_012714b.indd 61/27/14 3:11 PM
To view detailed instructional videos regarding features in this Quick Reference Guide, please go to www.nissanownersinfo.mobi.

16
FIRST DRIVE FEATURES
03
0506
02
01
FM/AM/SiriusXM®* SATELLITE RADIO WITH CD/DVD PLAYER
(if so equipped)
01 ON•OFF BUTTON/VOL (volume) CONTROL KNOB

Press the VOL/ON•OFF control knob to turn the system on or off.

Turn the knob right or left to increase or decrease the volume.
02 SEEK/CAT AND TRACK BUTTONS

To scan quickly through each broadcasting station, press the SEEK/CAT button or
the TRACK
button to stop at the previous or next broadcast station.

For satellite radio, to switch to the first channel of the previous or next category, press the
SEEK/CAT button or the TRACK button.

To change tracks on a CD, press the SEEK/CAT button or the TRACK button.

To rewind or fast forward a track on a CD, press and hold the SEEK/CAT button or
the TRACK
button.
03 AUDIO BUTTON/TUNE•FOLDER CONTROL KNOB

Press the AUDIO button to go to the audio settings screen.

To manually tune the radio, turn the TUNE/FOLDER knob left or right.
04 STATION PRESET BUTTONS

Twelve stations can be set for the FM band, six for the AM band and eighteen for
satellite radio.

To store a station in a preset, you must first select a radio band by pressing the
AM•FM button
05 or
S AT button
06, then tune to the desired AM, FM or XM
satellite radio station.

Then press and hold the desired station preset button (1-6) until the sound is briefly
muted. The channel indicator will then display and the sound will resume. Programing\
is
now complete.

To retrieve a previously set station, select the radio band where the preset was stored
then press the corresponding station select button (1-6).
*SiriusXM® Satellite Radio is only available on vehicles equipped with an optional s\
atellite radio subscription service.
For more information, refer to the “Monitor, heater, air conditioner, audio, phone and voice recognition systems (section
4)” of your Owner’s Manual.
04
1591421_14d_Murano_QRG_012714b.indd 161/27/14 3:11 PM
To view detailed instructional videos regarding features in this Quick Reference Guide, please go to www.nissanownersinfo.mobi.

17
FRONT ARMREST/CENTER CONSOLE STORAGE BOX
To access the top storage bin, pull
up on the driver’s side lever
01.

To access the bottom storage bin, pull
up on the passenger side lever
02.
For more information, refer to the “Instruments and
controls (section 2)” of your Owner’s Manual.0201
CRUISE CONTROL
The cruise control system enables you to set a
constant cruising speed once the vehicle has
reached 25 MPH (40 km/h).

The system will automatically maintain the set speed
until you tap the brake pedal, accelerate, cancel or
turn the system off.

To activate the cruise control, push the ON/OFF
switch
01. The CRUISE indicator light in the instrument panel will illuminate.

To set a cruising speed, accelerate the vehicle to the desired speed, pus\
h the COAST/SET
switch
02 and release. Take your foot off the accelerator pedal. Your vehicle will maintain

the set speed.

To reset at a faster cruising speed, push and hold the ACCEL/RES switch 03. When the
vehicle attains the desired speed, release the switch.

To reset at a slower cruising speed, push and hold the COAST/SET switch 02. Release
the switch when the vehicle slows to the desired speed.

To cancel the preset speed, tap the brake pedal or push the CANCEL switch 04.

To turn off cruise control, push the ON/OFF switch 01. The CRUISE indicator light
in the
instrument panel will extinguish.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
01
02
03
04
USB/ iP OD® INTERFACE (if so equipped)
The USB jack 01 is located in the center console
under the arm rest.

When a compatible USB memory device or iPod® is
plugged into the USB jack, compatible audio and
video files stored on the device can be played
through the vehicle’s audio system and front display.
For more information, refer to the “Monitor, climate, audio, phone and
voice recognition systems (section 4)” of your Owner’s Manual.01
1591421_14d_Murano_QRG_012714b.indd 171/27/14 3:11 PM
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.

18
TRIP COMPUTER
When the button 01
is pressed, the following

modes will appear on the vehicle information
display
02 :
• MPG/AVG – Displays the current and average
fuel consumption since the last reset.
• MPG/MPH – Displays the average fuel
consumption and speed since the last reset.
• TIME/miles – Displays the elapsed time and
total distance the vehicle has been driven since
the last reset.
• RANGE – Displays the estimated distance
to empty (dte) the vehicle can be driven
before refueling.
• OUTSIDE TEMP – Displays the exterior air
temperature, including a low temperature
warning feature.
• SETTING – Allows you to set reminders for alerts and maintenance intervals or change
the language and units used in the system.
— Press the

button 03 to cycle through the various setting modes.

— Press the

button 01 to choose the selected menu.

• WARNING – Displays when a warning is present.

Press and hold the TRIP RESET button 04 for approximately 1 second to reset the currently
displayed trip odometer to zero.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
03
01
SYSTEM GUIDE
04
02
1591421_14d_Murano_QRG_012714b.indd 181/27/14 3:11 PM
To view detailed instructional videos regarding features in this Quick Reference Guide, please go to www.nissanownersinfo.mobi.

20
SYSTEM GUIDE
Bluetooth® System with Navigation (if so equipped)
Bluetooth® Streaming Audio allows you to use a
compatible Bluetooth® phone to play audio files on
your device. Your compatible cellular phone can be
connected to the vehicle’s audio system, allowing audio files to play through the vehicle’s speakers.
CONNECTING PROCEDURE

The vehicle must be stationary when connecting
the phone.
1. Press the PHONE button on the instrument panel
or the
button on the steering wheel and select the
“Connect Phone” key.
2. Initiate connecting from the phone.

• The connecting procedure varies according to each
cellular phone model. For detailed connecting instructions and a list of compatible phones, please
visit www.nissanusa.com/bluetooth.
• When prompted for a PIN code, enter “1234” from
the handset. (The PIN code is assigned by NISSAN
and cannot be changed.)
3. When the connecting is complete, the screen will
return to the “Phone” menu display.
PHONEBOOK SETUP

Depending on your cellular phone, the system may
automatically download your cellular phone’s entire phonebook to the vehicle’s Bluetooth
® system.

If the phonebook does not download automatically,
the vehicle phonebook may be set for up to
40 entries.

To manually download entries:
1. Press the

button and select the
“Quick Dial” key.
2. Select the “Add New” key at the top of
the display. There are different methods
to input a phone number. Select one of
the following options:
•

“Copy from Call History” to save a number from the Outgoing, Incoming or Missed
Calls lists.
• “Copy from the Phonebook” to save a number that has been downloaded from your
handset to the vehicle.
•
“Enter Number by Keypad” to input the number and name manually.
1591421_14d_Murano_QRG_012714b.indd 201/27/14 3:12 PM
To view detailed instructional videos regarding features in this Quick Reference Guide, please go to www.nissanownersinfo.mobi.