ignition NISSAN PATHFINDER 2013 R52 / 4.G Quick Reference Guide

To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.2
new system features
REMoTE ENGiN E START (if so equipped)
The remote start operating range is approximately
200 feet (60 m) from the vehicle. The effective
operating range may be shorter if there are walls or
other obstructions between the key and the car.
For remote start to function the car must be in park with the ignition off and all doors must be closed and
locked. Please see your Owner’s Manual for additional information.
To start your car remotely:



1. Press the button 01 .



2.


W

ithin 5 seconds press and hold the engine start
button 02 for at least 2 seconds.
The engine will start.
The parking lights will turn on.
Automatic climate control will begin heating or cooling the vehicle depe\
nding on the

outside temperature.
The engine will run for 10 minutes and then turn off.
Repeat steps 1 and 2 to extend the time for an additional 1 0 minute period.



•

After two remote st
arts the ignition switch must be cycled before remote start can be
used again.
To start driving depress the brake pedal and push the ignition switch START/STo P button.
*Laws in some communities may restrict the use of remote starters. check local regulations before using this feature.
F or more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
0201
ARo UND viEW® MoNi To R SYSTEM
W
i
TH CAMERA A i
D
ED S
o
NAR
(parking sensor) (if so equipped)
With the ignition switch in the o N position, the
Around View® Monitor is activated by pressing the
CAMERA button
01 , located on the control panel,
or by moving the shift lever to the R (RE v ERSE)
position. The control panel displays various views of
the position of the vehicle.
When the shift lever is in the P (PARK), N (NEUTRA l ) or D (DR
iv
E) position and the
CAMERA button
01 is pressed, the front view &
bird’s eye view screen is displayed.
When CAMERA button 01 is pressed again the


front view & front-side view screen is displayed.

01
FRoNT viEW & BiR D’S EYE viEW
FRoNT viEW & FRo NT-SiD E viEW
1351506_13c_Pathfinder_QRG_013013.indd 21/31/13 9:10 AM

TiRE PRESSURE MoNi To RiN G SYSTEM (TPMS)
with Easy Fill Tire Alert
A Tire Pressure l ow – Add Air warning message
will appear in the vehicle information display
01 and
the low tire pressure warning light
02 will illuminate
when one or more tires are low on pressure and air
is needed.



•


T

he tire pressures should be checked when the
tires are cold. The tires are considered cold after
the vehicle has been parked for 3 hours or more or
driven less than 1 mi (1.6 km) at moderate speeds.
When adding air to an under-inflated tire, the TPMS with Easy Fill Tire Alert provides visual and
audible signals to help you inflate the tires to the
recommended
c
O
LD tire pressure.



T
o use the Easy Fill Tire Alert:



1.

Move the shift lever to the
P (PARK) position and apply the parking brake.



2.

Place the ignition switc
h in the o N position. Do not start the engine.



3.

Add air to the under-inflated tire and within a few seconds, the hazar\
d warning lights will

start flashing.



4.

W
hen the designated tire pressure is reached, the horn will beep once and the hazard
warning flashers will stop flashing.



5.

Repeat this procedure for any additional under-inflated tires.
02
01
looSE FUEl CAP
A looSE FUEl CAP warning message will appear
in the vehicle information display
01 when the
fuel-filler cap is not tightened correctly.
To tighten, turn the cap clockwise until a single click
is heard.
The warning message will disappear when the vehicle detects the fuel-filler cap is properly tightened and the
reset
button 02 is pressed for about 1 second.
If the cap is not properly tightened, the Malfunction

Indicator Light
may illuminate.
For more information, refer to the “instruments and controls (section 2)” and the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
02
01
essential information
4To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
1351506_13c_Pathfinder_QRG_013013.indd 41/31/13 9:10 AM

PoWER liFT GATE (if so equipped)
When the liftgate is closed and locked, the liftgate
will open automatically by:



•

Pushing the power liftgate switc
h
01 on the
instrument panel.



•


Pressing the button 02 on the NISSAN
Intelligent
k
ey for more than 0.5 seconds
To open the liftgate with the liftgate opener switch
03 , the liftgate must be unlocked, or have Intelligent
key with you ( in your poc
ket or purse).
The power liftgate operation can be turned on or off by the power liftgate main switch
04 on the
instrument panel.
When the power liftgate main switch 04 is pushed
to the
o
FF position, power operation is not available
using the power liftgate switch on the liftgate
05 or
the liftgate opener switch
03 .
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
0104
0502
iNTElliGENT KEY BATTERY DiSCHARGE
If the battery of the Intelligent key is disc harged, or
environmental conditions interfere with the Intelligent
key operation, st

art the engine according to the
following procedure:



1.

Move the shift lever to the
P (PARK) position.



2.

Firmly apply the foot brake.



3.

T
ouch the ignition switch with the Intelligent k
ey

and a chime will sound.



4.

W
ithin 10 seconds after the chime sounds, push the ignition switch while depressing the
brake pedal and the engine will start.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving
(section 5)” and the “Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
7
03
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
1351506_13c_Pathfinder_QRG_013013.indd 71/31/13 9:10 AM

THiRD RoW SEATS
To recline the seatback, pull up on the latch 01
located on the outside corner of each seatback. Lean
back until the desired angle is obtained.
To bring the seatback forward again, pull up on the latch
01 and move your body forward. The seatback
will move forward.
For more information, refer to the “Safety—seats, seat belts and supplemental restraint system (sect\
ion 1)” of your
Owner’s Manual.
01
AUTo MAT iC D Riv E Po Si T io NER
(if so equipped)
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner
01 memory.
Follow these procedures to set the memory positions:



•

Confirm the shift lever is in the
P (PARK) position.



•

Push the ignition switc
h to the o N position.



•

Adjust the driver
’s seat, steering column and outside mirrors to the desired positions
using the adjusting switches for each feature.



•

Push the
SET switch and within 5 seconds, push the memory switch (1 or 2) for at
least 1 second.



•

T
he indicator light on the memory switch you select will illuminate for approximately
5 seconds.



•

T
he driver’s seat, steering column and outside mirror positions are now set to
your preference.
These memorized positions can also be linked to your NISSAN Intelligent key®.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
01
9To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
1351506_13c_Pathfinder_QRG_013013.indd 91/31/13 9:10 AM

first drive features
STARTiNG/SToPP iN G THE ENGiN E
Depress the brake pedal.
Press the ignition switch START/STo P button to start
the engine.
NOTE: It is important to make sure the NISSAN Intelligent
k

ey
® is with you (that is, in your pocket or purse).
TURNING THE ENGINE OFF
Move the shift lever to the P (PARK) position and apply the parking brake.
Press the ignition switch START/STo P button to turn the engine off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
oUTSiDE MiRRo R C o NTRol SW i TCH
(if so equipped)
To select the right or left side mirror, move the control
switch
01 right or left.
Adjust eac h mirror to the desired position using the
switch
02 .
REVERSE TILT-DOWN FEATURE (if so equipped)
The reverse tilt-down feature will turn the selected outside mirror surfa\
ce downward to provide better rear visibility close to the vehicle.



1.

Set the parking brake.



2.

Push the ignition switc
h to the o N position.



3.

Move the shift lever to the
R (RE v ERSE) position.



4.
c hoose the right or left outside mirror by operating the outside mirror c\
ontrol switch
01 .



5.


T

he outside mirror surfaces move downward.
The outside mirror surfaces will return to their original positions when \
one of the following conditions has occurred:



•

T
he shift lever is moved to any position other than R (RE v ERSE).



•

T
he outside mirror control switch is set to the center “neutral” position.



•

T
he ignition switch is placed in the o FF position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
0102
10To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.
1351506_13c_Pathfinder_QRG_013013.indd 101/31/13 9:10 AM

HEADliGHT Co NTRol SW i TCH
HEADLIGHT cONTROL
Turn the headlight control switch to the position
01 to turn on the front parking, tail, license plate and
instrument panel lights. Turn the switch to the

position
02 to turn on the headlights.
AUTOLIGHT SYSTEM (if so equipped)
The autolight system will automatically turn the headlights on when it is dark and off when it is light.
The system will keep the headlights on for a period of
time after you turn the ignition off and all doors are closed.
To activate the autolight system, turn the headlight control switch to the AUTo position 03
then push the ignition switch to
o
N. To deactivate the autolight system, turn the headlight
control switch to the
o
FF,
01 or position 02 .
HIGH BEAM SELE
cT
Push the headlight control switc h forward 04 to select the high beam function. The blue
indicator light
illuminates in the instrument panel. Pull the headlight switch back to the
original position to select the low beam. The blue indicator light goes off.
Pull and release the headlight control switc h 05 to flash the headlight high beams on and off.
FOG LIGHT SWIT
cH
N

OTE: The headlights must be on and the low beams
selected for the fog lights to operate.
Turn the switch (inside collar) to the position 06 to turn the fog lights on.
Turn the switch (inside collar) to the o FF position to turn the fog lights off.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
03
01
02
04
0506
11To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
1351506_13c_Pathfinder_QRG_013013.indd 111/31/13 9:10 AM

first drive features
CRUiSE Co NTRol
The cruise control system enables you to set a
constant cruising speed once the vehicle has
reached 25 MPH (40 km/h).
The system will automatically maintain the set speed until you tap the brake pedal, accelerate, cancel or
turn the system off.
To activate the cruise control, push the ON•OFF switch 01 .
CRU i SE
will be displayed in
the vehicle information display.
To set a cruising speed, accelerate the vehicle to the desired speed, pus\
h the C oAST/
S ET switch
02 and release. The SET indicator light in the vehicle information display will
illuminate. Take your foot off the accelerator pedal. Your vehicle will maintain the set speed.
To reset at a faster cruising speed, push and hold the ACCE l/RES switc h 03 . When the
vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push and hold the C oAST/ SET switch 02 . Release
the switch when the vehicle slows to the desired speed.
To cancel the preset speed, push the CANCEl switch 04 .
To turn off cruise control, push the o N/ o FF switch 01 . Both the CRU i SE
indicator light
and the SET indicator light in vehicle information display will turn off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
PoWER o UT l ETS (if so equipped)
12V OUTLETS
The power outlets are for powering electrical
accessories such as cellular telephones. They
are rated at 12 volt, 120W (10A) maximum.
To use a power outlet, open the cap.
The power outlets on the instrument panel 01
and inside the center console 02 are powered

only when the ignition switch is in the ACC or
o

N position.
The power outlet in the cargo area 03 is powered

all the time.

0102
03
04
01
02
03
16To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
1351506_13c_Pathfinder_QRG_013013.indd 161/31/13 9:10 AM

FUEl-F ill ER Doo R
The fuel-filler door is located on the driver’s side of
the vehicle.
The fuel-filler door automatically locks or unlocks when the driver’s door is locked or unlocked.
To open the fuel-filler door after unlocking, push
the right side of the fuel-filler door.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
04
05
120V OUTLET (if so equipped)
The 120V outlet 04 is located on the back of the
center console.
To use the outlets for devices that require 120V
power, place the ignition in the o N position and push
the power inverter switch
05 .
The switch will illuminate when enabled.
For more information, refer to the “instruments and controls (section 2)”

of your Owner ’s Manual.
17To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
1351506_13c_Pathfinder_QRG_013013.indd 171/31/13 9:10 AM