Timing NISSAN TEANA 2003 Service Manual

CAMSHAFT
EM-197
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

VALVE LIFTER HOLE DIAMETER

Measure inner diameter of valve lifter hole of cylinder head with
inside micrometer.
VALVE LIFTER CLEARANCE

(Valve lifter clearance) = (Valve lifter hole diameter) – (Valve lifter outer diameter)

If out of the standard, referring to each standard of valve lifter outer diameter and valve lifter hole diame-
ter, replace either or both valve lifter and cylinder head.
INSTALLATION
1. Install timing chain tensioners (secondary) on both cylinder
heads (right and left banks).

Install timing chain tensioner (secondary) with its stopper pin
attached.

Install timing chain tensioner (secondary) with sliding part fac-
ing downward on cylinder head (right bank), and with sliding
part facing upward on cylinder head (left bank).

Install new O-ring as shown in the figure.
2. Install valve lifters.

Install them in the original position.
3. Install camshafts.

Install camshaft with dowel pin attached to its front end face
on the exhaust side.Standard
Intake
VQ23DE : 30.015 - 30.031 mm (1.1817 - 1.1823 in)
VQ35DE : 34.000 - 34.016 mm (1.3386 - 1.3392 in)
Exhaust
VQ23DE : 30.003 - 30.019 mm (1.1812 - 1.1818 in)
VQ35DE : 34.000 - 34.016 mm (1.3386 - 1.3392 in)
SEM867E
Standard
Intake
VQ23DE : 0.028 - 0.054 mm (0.0011 - 0.0021 in)
VQ35DE : 0.013 - 0.039 mm (0.0005 - 0.0015 in)
Exhaust
VQ23DE : 0.016 - 0.042 mm (0.0006 - 0.0017 in)
VQ35DE : 0.013 - 0.039 mm (0.0005 - 0.0015 in)
PBIC2111E
KBIA1071E

EM-200
[VQ]
CAMSHAFT

5. Tighten camshaft bracket bolts in the following steps, in numeri-
cal order as shown in the figure.
a. Tighten No. 7 to 10 in order as shown.
b. Tighten No. 1 to 6 in order as shown.
c. Tighten No. 1 to 10 in numerical order as shown.
d. Tighten No. 1 to 10 in numerical order as shown.
CAUTION:
After tightening mounting bolts of camshaft brackets (No.
1), be sure to wipe off excessive liquid gasket from the
parts list below.

Mating surface of rocker cover

Mating surface of rear timing chain case
6. Measure the difference in levels between front end faces of
camshaft bracket (No. 1) and cylinder head.

Measure two positions (both intake and exhaust side) for a
single bank.

If measured value is out of the standard, re-install camshaft
bracket (No. 1).
7. Check and adjust the valve clearance. Refer to EM-202, "
Valve Clearance" .
8. Install in the reverse order of removal after this step. : 1.96 N·m (0.20 kg-m, 1 ft-lb)
: 1.96 N·m (0.20 kg-m, 1 ft-lb)
: 5.88 N·m (0.60 kg-m, 4 ft-lb)
: 10.4 N·m (1.1 kg-m, 8 ft-lb)
PBIC2050E
Standard : −0.14 to 0.14 mm (−0.006 to 0.006 in)
EMQ0044D

CAMSHAFT
EM-201
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

INSPECTION AFTER INSTALLATION
Inspection of Camshaft Sprocket (INT) Oil Groove
CAUTION:

Perform this inspection only when DTC P0011 or P0021 are detected in self-diagnostic results of
CONSULT-II and it is directed according to inspection procedure of EC section. Refer to EC-427,
"SELF-DIAG RESULTS MODE" .

Check when engine ins cold so as to prevent burns from any splashing engine oil.
1. Check the engine oil level. Refer to LU-19, "
ENGINE OIL" .
2. Perform the following procedure so as to prevent the engine from being unintentionally started while
checking.
a. Release fuel pressure. Refer to EC-392, "
FUEL PRESSURE RELEASE" .
b. Disconnect ignition coil and injector harness connectors.
3. Remove intake manifold control solenoid valve. Refer to EM-192, "
CAMSHAFT" .
4. Crank the engine, and then make sure that engine oil comes out
from camshaft bracket (No. 1) oil hole. End crank after checking.
WARNING:
Be careful not to touch rotating parts (drive belts, idler pul-
ley, and crankshaft pulley, etc.).
CAUTION:
Engine oil may squirt from intake valve timing control sole-
noid valve installation hole during cranking. Use a shop
cloth to prevent the engine components and the vehicle. Do
not allow engine oil to get on rubber components such as
drive belt or engine mount insulators. Immediately wipe off
any splashed engine oil.

Clean oil groove between oil strainer and intake valve timing control solenoid valve if engine oil does not
come out from camshaft bracket (No. 1) oil hole. Refer to LU-17, "
LUBRICATION SYSTEM" .
5. Remove components between intake valve timing control solenoid valve and camshaft sprocket (INT),
and then check each oil groove for clogging.

Clean oil groove if necessary. Refer to LU-17, "LUBRICATION SYSTEM" .
6. After inspection, install removed parts.
Inspection for Leaks
The following are procedures for checking fluids leak, lubricates leak and exhaust gases leak.

Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to MA-14, "
RECOMMENDED FLUIDS AND LUBRICANTS" .

Use procedure below to check for fuel leakage.
–Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
–Start engine. With engine speed increased, check again for fuel leakage at connection points.

Run engine to check for unusual noise and vibration.
NOTE:
If hydraulic pressure inside timing chain tensioner drops after removal/installation, slack in the guide may
generate a pounding noise during and just after engine start. However, this is normal. Noise will stop after
hydraulic pressure rises.

Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids
including engine oil and engine coolant.

Bleed air from lines and hoses of applicable lines, such as in cooling system.

After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
PBIC2869E

EM-202
[VQ]
CAMSHAFT

Summary of the inspection items:
* Transmission/transaxle/CVT fluid. power steering fluid, brake fluid, etc.
Valve ClearanceBBS004W2
INSPECTION
In cases of removing/installing or replacing camshaft and valve-
related parts, or of unusual engine conditions due to changes in
valve clearance (found malfunctions during stating, idling or causing
noise), perform inspection as follows:
1. Remove rocker covers (right and left banks). Refer to EM-160, "
ROCKER COVER" .
2. Remove splash guard (RH).
3. Measure the valve clearance as follows:
a. Set No. 1 cylinder at TDC of its compression stroke.

Rotate crankshaft pulley clockwise to align timing mark
(grooved line without color) with timing indicator.

Make sure that intake and exhaust cam noses on No. 1 cylin-
der (engine front side of right bank) are located as shown in
the figure.

If not, rotate crankshaft one revolution (360 degrees) and
align as shown in the figure.
Item Before starting engine Engine running After engine stopped
Engine coolant Level Leakage Level
Engine oil Level Leakage Level
Other oils and fluid* Level Leakage Level
Fuel Leakage Leakage Leakage
Exhaust gases — Leakage —
SEM713A
SEM918G
SEM418G

EM-208
[VQ]
OIL SEAL

Removal and Installation of Front Oil SealBBS004W4
REMOVAL
1. Remove the following:

Right side front road wheel and tire.

Splash guard (RH)

Drive belts; Refer to EM-128, "DRIVE BELTS" .

Crankshaft pulley; Refer to EM-173, "TIMING CHAIN" .
2. Remove front oil seal using suitable tool.
CAUTION:
Be careful not to damage front timing chain case and crank-
shaft.
INSTALLATION
1. Apply engine oil to both oil seal lip and dust seal lip.
2. Install front oil seal.

Install front oil seal so that each seal lip is oriented as shown
in the figure.

Using suitable drift, press-fit until the height of front oil seal is
level with the mounting surface.
–Suitable drift: outer diameter 60 mm (2.36 in), inner diameter
50 mm (1.97 in).
CAUTION:

Be careful not to damage front timing chain case and
crankshaft.

Press-fit straight and avoid causing burrs or tilting oil
seal.
3. Install in the reverse order of removal after this step.
Removal and Installation of Rear Oil SealBBS004W5
REMOVAL
1. Remove engine assembly from vehicle, and separate front suspension member and transaxle from
engine. Refer to EM-223, "
ENGINE ASSEMBLY" .
2. Install engine sub-attachment with engine stand shaft [SST: KV10117001 and KV10106500] to right side
of cylinder block, then lift engine, and mount it onto engine stand [SST: ST0501S000]. Refer to EM-228,
"CYLINDER BLOCK" .
3. Remove drive plate. Refer to EM-228, "
CYLINDER BLOCK" .
4. Remove oil pan (upper). Refer to EM-145, "
OIL PAN AND OIL STRAINER" .
SEM829E
SEM715A
SEM829E

SERVICE DATA AND SPECIFICATIONS (SDS)
EM-255
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00100
Standard and LimitBBS004WE
GENERAL SPECIFICATIONS
VA LV E T I M I N G
EngineVQ23DE VQ35DE
Cylinder arrangementV- 6
Displacement cm
3 (cu in)2,349 (143.34) 3,498 (213.45)
Bore and stroke mm (in)85.0 × 69.0
(3.346 × 2.717)95.5 × 81.4
(3.760 × 3.205)
Valve arrangementDOHC
Firing order1-2-3-4-5-6
Number of piston ringsCompression 2
Oil 1
Number of main bearings4
Compression ratio 9.8 10.3
Compression pressure
kPa (bar, kg/cm
2 , psi) / 300 rpmStandard 1,050 (10.5, 10.7, 152) 1,270 (12.7, 13.0, 184)
Minimum 750 (7.5, 7.7, 109) 980 (9.8, 10.0, 142)
Differential limit between cylinders 100 (1.0, 1.0, 15) 100 (1.0, 1.0, 15)
Cylinder number
SEM713A
Valve timing
(Intake valve timing control - “OFF”)
Unit: degree
abcde f
VQ23DE 232 230−757646
VQ35DE 240 238−664852
PBIC0187E

TERMINOLOGY
GI-45
C
D
E
F
G
H
I
J
K
L
MB
GI

TERMINOLOGYPFP:00011
SAE J1930 Terminology List BAS00081
All emission related terms used in this publication in accordance with SAE J1930 are listed. Accordingly, new
terms, new acronyms/abbreviations and old terms are listed in the following chart.
NEW TERMNEW ACRONYM /
ABBREVIATIONOLD TERM
Air cleaner ACL Air cleaner
Barometric pressure BARO ***
Barometric pressure sensor-BCDD BAROS-BCDD BCDD
Camshaft position CMP ***
Camshaft position sensor CMPS Crank angle sensor
Canister *** Canister
Carburetor CARB Carburetor
Charge air cooler CAC Intercooler
Closed loop CL Closed loop
Closed throttle position switch CTP switch Idle switch
Clutch pedal position switch CPP switch Clutch switch
Continuous fuel injection system CFI system ***
Continuous trap oxidizer system CTOX system ***
Crankshaft position CKP ***
Crankshaft position sensor CKPS ***
Data link connector DLC ***
Data link connector for CONSULT-II DLC for CONSULT-II Diagnostic connector for CONSULT-II
Diagnostic test mode DTM Diagnostic mode
Diagnostic test mode selector DTM selector Diagnostic mode selector
Diagnostic test mode I DTM I Mode I
Diagnostic test mode II DTM II Mode II
Diagnostic trouble code DTC Malfunction code
Direct fuel injection system DFI system ***
Distributor ignition system DI system Ignition timing control
Early fuel evaporation-mixture heater EFE-mixture heater Mixture heater
Early fuel evaporation system EFE system Mixture heater control
Electrically erasable programmable read
only memoryEEPROM ***
Electronic ignition system EI system Ignition timing control
Engine control EC ***
Engine control module ECM ECCS control unit
Engine coolant temperature ECT Engine temperature
Engine coolant temperature sensor ECTS Engine temperature sensor
Engine modification EM ***
Engine speed RPM Engine speed
Erasable programmable read only memory EPROM ***
Evaporative emission canister EVAP canister Canister
Evaporative emission system EVAP system Canister control solenoid valve
Exhaust gas recirculation valve EGR valve EGR valve

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Heated oxygen sensor 1 (bank 2) .... EC-486, EC-496,
EC-696
Heated oxygen sensor 1 heater ...................... EC-308
Heated oxygen sensor 1 heater (bank 1) ........ EC-706
Heated oxygen sensor 1 heater (bank 2) ........ EC-706
Heated oxygen sensor 2 .................................. EC-313
Heated oxygen sensor 2 (bank 1) ..... EC-714, EC-723
Heated oxygen sensor 2 (bank 2) ..... EC-714, EC-723
Heated oxygen sensor 2 heater ...................... EC-319
Heated seat ....................................................... SE-61
Heater and cooling unit (Heater core) ........... ATC-119
HFC134a (R134a) system precaution ............... ATC-5
HFC134a (R134a) system service procedure ATC-131
HFC134a (R134a) system service tools .......... ATC-16
HFC134a system service equipment precaution ..........
ATC-12
HLC - Wiring diagram ...................................... WW-43
HO2S1 - Wiring diaram ..................... EC-145, EC-152
Horn ................................................................. WW-62
HORN - Wiring diagram ................................... WW-62
How to erase DTC for OBD system ..... EC-35, EC-376
HSEAT - Wiring diagram ................................... SE-70
I
IATSEN - Wiring diagram .................. EC-325
, EC-731
Idle air volume learning ....................... EC-47, EC-389
Idle speed .............................. EC-40, EC-381, EC-387
Ignition coil ......................................... EC-329, EC-735
Ignition coil(QR20DE) ........................................ EM-31
Ignition coil(VQ23DE and VQ35DE) ................ EM-152
Ignition control system ....................... EC-329, EC-735
Ignition timing ........................ EC-40, EC-381, EC-387
IGNSYS - Wiring diagram .................. EC-330, EC-736
In vehicle sensor ............................. ATC-99, ATC-110
INF/D - Wring diagram ........................... AV-43, AV-65
INJECT - Wiring diagram ................... EC-290, EC-685
Injector ............................................... EC-289, EC-684
Input/Output signal of TCM .............................. CVT-19
Instrument panel .................................................. IP-10
INT/L - Wiring diagram ..................................... LT-217
Intake air temperature sensor ............ EC-324, EC-730
Intake door control linkage adjustment ............ ATC-71
Intake door motor ........................... ATC-69, ATC-117
Intake manifold collector(VQ23DE and VQ35DE) ........
EM-133
Intake manifold(QR20DE) ................................. EM-19
Intake manifold(VQ23DE and VQ35DE) ......... EM-138
Intake sensor ................................ ATC-105, ATC-112
Intake valve timing control ............................... EC-116
Intake valve timing control (Bank 1) ................ EC-461
Intake valve timing control (Bank 2) ................ EC-461
Intake valve timing control solenoid valve (Bank 1) ......
EC-545
Intake valve timing control solenoid valve (Bank 2) ......
EC-545
Interior ................................................................. EI-38
Interior lamp ........................................ LT-217, LT-219
IPDM (Intelligent power distribution module engine room) ................................................................. PG-17
IVC - Wiring diagram ....................................... EC-119
IVCB1 - Wiring diagram ................................... EC-546
IVCB2 - Wiring diagram ................................... EC-548
K
Knock sensor (KS) ............................. EC-164
, EC-512
KS - Wiring diagram ........................... EC-165, EC-513
L
L/USSV - Wiring diagram ............................... CVT-148
LAN system circuit ........................................... ATC-59
LCD display ....................................................... AV-61
Line pressure and secondary pressure control CVT-20
Line pressure solenoid valve .......... CVT-97, CVT-102
Line pressure test (A/T) ..................................... AT-46
Liquid gasket application(QR20DE) ........... EM-6, LU-3
Liquid gasket application(VQ23DE and VQ35DE) ........
EM-120
, LU-15, CO-3, CO-27
Location of electrical units ................................. PG-67
Lock-up and select control ............................... CVT-21
Lock-up select solenoid valve ........................ CVT-147
LPSV - Wiring diagram ...................... AT-127, CVT-98
Lubricant (R134a) A/C ..................................... ATC-21
Lubricants ......................................................... MA-14
Lubrication circuit (engine)(QR20DE) .................. LU-5
Lubrication circuit (engine)(VQ23DE and VQ35DE) .....
LU-17
Lubrication oil A/C .......................................... ATC-150
M
MAFS - Wiring diagram ..................... EC-126
, EC-468
Magnet clutch ................................. ATC-78, ATC-136
MAIN - Wiring diagram ........ EC-106, EC-451, AT-158
Maintenance (engine)(VQ23DE and VQ35DE) MA-24
Malfunction indicator (MI) .................... EC-36, EC-377
Mass air flow sensor (MAFS) ............. EC-124, EC-466
Meter ..................................................................... DI-4
METER - Wiring diagram .................................... DI-10
MIL data link connectors circuit ......... EC-344, EC-763
MIL/DL - Wiring diagram .................... EC-344, EC-763
Mirror, door ......................................... GW-74, GW-77
Mirror, out side .................................... GW-74, GW-77
MMSW - Wiring diagram ................................ CVT-114
Mode door control linkage adjustment ............. ATC-65
Mode door motor ............................ ATC-63, ATC-123
Molding - See Exterior EI-25, EI-27, EI-28, EI-29, EI-30
Mud guard - See Exterior .................................... EI-24
Multiport fuel injection (MFI) system .... EC-21, EC-358
Multiport fuel injection precautions ....................... GI-6
N
NATS - Wiring diagram .................................... BL-143
NATS (Nissan anti-theft system) precautions ....... GI-3
NONDTC - Wiring diagram .............. AT-168, CVT-160

IDX-7
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
SECPSV - Wiring diagram ............................. CVT-109
SEN/PW - Wiring diagram ................. EC-234, EC-591
SESCVT - Wiring diagram ............................... CVT-80
SHIFT - Wiring diagram ................... AT-217, CVT-181
Shift control ...................................................... CVT-20
Shift control system ....................................... CVT-176
Shift lock system .............................................. AT-216
Shift schedule ................................. CVT-40, CVT-198
Side air bag (satellite) sensor .......................... SRS-45
Side curtain air bag .......................................... SRS-42
Side trim .............................................................. EI-38
SMJ (super multiple junction) ............................ PG-76
Spark plug replacement(QR20DE) .................... MA-22
Spark plug replacement(VQ23DE and VQ35DE) .........
MA-32
Spark plug(VQ23DE and VQ35DE) ................. EM-153
Specification value ............................... EC-95, EC-440
Speedometer ........................................................ DI-4
Spiral cable ...................................................... SRS-37
SROOF - Wiring diagram .................................. RF-13
SRS - See Supplemental Restraint System ...... SRS-5
SRS Trouble diagnoses ..................................... SRS-7
SSV/A - Wiring diagram ..................................... AT-91
SSV/B - Wiring diagram ..................................... AT-96
Stall Test .......................................................... CVT-32
Stall test (A/T) .................................................... AT-43
Standardized relay ............................................. PG-77
START - Wiring diagram ................................... SC-15
Starter ................................................................ SC-14
Starting system .................................................. SC-14
Steering gear and linkage inspection ................ MA-41
Steering linkage ................................................. PS-17
Steering wheel and column ..................... PS-9, PS-12
Step motor .................................... CVT-153, CVT-157
STM - Wiring diagram .................................... CVT-154
Stop lamp ......................................................... LT-190
Stop lamp switch .. EC-245, EC-602, EC-626, EC-660
STOP/L - Wiring diagram ................................. LT-190
STSIG - Wiring diagram .................................. CVT-57
Sun roof, electric ................................................ RF-10
Sunload sensor ............................. ATC-102, ATC-111
Sunroof .................................................. RF-10, RF-22
Sunshade ............................................................ EI-46
Supplemental Restraint System ........................ SRS-5
Suspension ........................................................ MA-42
Symbols and abbreviations ..................... GI-10, GI-23
Symptom matrix chart .......................... EC-60, EC-402
T
Tachometer .......................................................... DI-4
TCM circuit diagram ........................................ CVT-31
TCM function ................................................... CVT-18
TCM inspection table ........................... AT-64, CVT-40
TCV - Wiring diagram ........................ AT-106, CVT-90
Thermostat(QR20DE) ........................................ CO-24
Thermostat(VQ23DE and VQ35DE) .................. CO-50
Three way catalyst precautions ............................ GI-6
Three way catalyst(QR20DE) ............................ EM-23
Three way catalyst(VQ23DE and VQ35DE) ... EM-140
Throttle control motor ......................... EC-213, EC-568
Throttle control motor relay ................ EC-207, EC-562
Throttle position sensor (TPS) .......... EC-136, EC-157,
EC-229
, EC-231, EC-265, EC-479, EC-505, EC-586,
EC-588
, EC-645
Throttle valve closed position learning . EC-47, EC-389
Timing chain(QR20DE) ..................................... EM-53
Timing chain(VQ23DE and VQ35DE) ............. EM-173
Tire rotation ....................................................... MA-40
Torque converter installation AT-244, AT-355, CVT-196
Torque convertor clutch solenoid valve .......... CVT-89,
CVT-94
TPS1 - Wiring diagram ...................... EC-159, EC-507
TPS2 - Wiring diagram ...................... EC-138, EC-481
TPS3 - Wiring diagram ...................... EC-267, EC-647
Trouble diagnoses .............................................. GI-11
Trunk lid ........................................................... BL-131
Trunk lid opener - See Trunk lid ...................... BL-136
TURN - Wiring diagram .................................... LT-156
Turn signal lamp ............................................... LT-152
Two trip detection logic ........................ EC-33, EC-373
U
Unified meter and A/C amp. ............................... DI-27
V
Vacuum hose (brake system) ............................ BR-24
Vacuum hose drawing (Engine control) EC-69, EC-412
Valve clearance ................................................ EM-50
Valve clearance(VQ23DE and VQ35DE) ....... EM-202
Valve guide(QR20DE) ...................................... EM-73
Valve guide(VQ23DE and VQ35DE) EM-218, EM-219
Valve lifter(QR20DE) ........................................ EM-41
Valve lifter(VQ23DE and VQ35DE) ................ EM-196
Valve seat(QR20DE) ........................................ EM-75
Valve seat(VQ23DE and VQ35D) ................... EM-220
Valve seat(VQ23DE and VQ35DE) ................ EM-220
Valve spring(QR20DE) ..................................... EM-76
Valve spring(VQ23DE and VQ35DE) ............. EM-221
Variable induction air control system (VIAS) ... EC-753
VDC -Wiring diagram ...................................... BRC-49
Vehicle speed sensor (VSS) EC-183, EC-243, EC-622,
EC-624
, EC-762
VFD display ....................................................... AV-41
VIAS - Wiring diagram ..................................... EC-755
Viscosity number (SAE) .................................... MA-15
VSS A/T - Wiring diagram .................................. AT-82
VSSMTR - Wiring diagram ................................ AT-87
W
W/ANT - Wiring diagram .................................... AV-38
WARN - Wiring diagram ..................................... DI-37
Warning chime .................................................... DI-56
Warning lamps .................................................... DI-35
Washer, front ..................................................... WW-4

AUTO LIGHT SYSTEM
LT-65
C
D
E
F
G
H
I
J
L
MA
B
LT


to BCM terminal 14.
AUTO LIGHT OPERATION
Applicable lamps

Low beam headlamp

Parking, license plate and tail lamps

High beam headlamp (with the lighting switch in HIGH BEAM position)

Front fog lamp (with the lighting switch in front fog lamp ON position)
When the lighting switch is in AUTO position with the ignition switch in ON position, BCM detects the AUTO
LIGHT (ON) by BCM combination switch reading function. BCM turns automatically ON/OFF the applicable
lamps according to ambient brightness depending on the following condition.

It turns ON applicable lamps in 3 seconds when ambient brightness is less than 1250 lux.

This lighted lamps is turned OFF in 5 seconds when ambient brightness becomes 2500 lux or higher.
Releasing Function:

Turn ignition switch to the OFF position, or

Change lighting switch to the OFF, 1ST, 2ND position.
NOTE:
Timing for when lamps turn ON/OFF can be changed by the function setting of CONSULT-II. Refer to LT- 1 9 ,
"WORK SUPPORT" .
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
HEADLAMP LOW AND HIGH OPERATION (XENON TYPE)
Refer to LT- 6 , "System Description" .
HEADLAMP LOW AND HIGH OPERATION (HALOGEN TYPE)
Refer to LT- 3 8 , "System Description" .
FRONT FOG LAMP OPERATION
Refer to LT- 1 2 6 , "System Description" .
PARKING, LICENSE PLATE AND TAIL LAMPS OPERATION
Refer to LT- 1 9 6 , "System Description" .
CAN Communication System DescriptionBKS001O7
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitBKS001O8
Refer to LAN-49, "CAN System Specification Chart" .
Major Components and FunctionsBKS001O9
Components Functions
BCM

Turns ON/OFF circuits of parking lamp, license plate lamp, tail lamp and headlamp according to signals from
optical sensor, lighting switch (AUTO), and ignition switch (ON, OFF).
Optical sensor

Converts outside brightness (lux) to voltage, and sends it to BCM. (Detects brightness of 800 to 2500 lux)