can NISSAN TEANA 2003 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2003, Model line: TEANA, Model: NISSAN TEANA 2003Pages: 3502, PDF Size: 74.56 MB
Page 729 of 3502
INTELLIGENT KEY SYSTEM
BL-71
C
D
E
F
G
H
J
K
L
MA
B
BL
Intelligent Key Lock-in Prevention Function
When Intelligent Key is in vehicle, a door is open, and doors are locked using door lock and unlock switch,
driver door lock knob, Intelligent Key unit sends door unlock request signal to BCM via CAN communication to
unlock all doors to prevent Intelligent Key from becoming locked in vehicle.
When Intelligent Key is in trunk room, all doors are lock and trunk lid is closed, Intelligent Key unit sends trunk
open signal to BCM. Then BCM open trunk lid and warning buzzer sounds for 10 seconds.
CAUTION:
The above function operates when the Intelligent Key is inside the vehicle. However, there may be
times when Intelligent Key cannot be detected and this function will not operate when Intelligent Key
is on the instrument panel, rear parcel shelf, or in the glove box. Also, this system some times does
not operate if the Intelligent Key is in the door pocket for the open door.
List of Operation Related Parts
Parts marked with × are the parts related to operation.
REMOTE KEYLESS ENTRY FUNCTIONS
Door Lock/Unlock Function
Operating a remote controller button on the Intelligent Key sends the Intelligent Key-ID to the Intelligent
Key unit. Intelligent Key unit conducts a verification of the received key-ID, and if the verification is
accepted, a door lock or door unlock request signal is sent to BCM via CAN communication to lock/unlock
the door lock.
When door lock/unlock is performed using Intelligent Key remote controller button operation, operation
confirmation is conducted by making hazard lamps flash and Intelligent Key warning buzzer sound.
Trunk Open Function
Operating a remote controller button on the Intelligent Key sends the Intelligent Key-ID to the Intelligent
Key unit.
Intelligent Key unit conducts a verification of the received key-ID, and if the verification is accepted, a
trunk open request signal is sent to BCM via CAN communication trunk lid is opened.
Operation Condition
Door lock/trunk open function
Intelligent Key
Key switch
Ignition knob switch
Door unlock sensor
Trunk room lamp switch
Door request switch
Trunk opener request switch
Door lock actuator
Trunk lid opener actuator
Inside key antenna
Outside key antenna (Driver, Passenger)
Outside key antenna (rear bumper)
Intelligent Key unit
CAN communication system
BCM
Combination meter
Hazard warning lamp
Door lock function by the request switch××××××××××××
Door lock function by the mechanical key××
Trunk open function by the trunk opener switch× × × ×× ××××
Hazard reminder function×××××
Remote controller button operation Operating condition
Lock
All doors are closed. (for lock operation)
Remove mechanical key from ignition key cylinder (key switch: OFF)
Ignition knob is not press (ignition knob switch: OFF)
Page 730 of 3502
BL-72
INTELLIGENT KEY SYSTEM
Hazard Reminder Function
The hazard lamps are flashed when the door lock is locked or unlocked by remote controller button.
When ignition switch ON or any door is opened, key reminder function is not operate.
List of Operation Related Parts
Parts marked with × are the parts related to operation.
ENGINE START FUNCTION
Operation Description
When ignition knob is pressed, Intelligent Key unit sends request signal from inside key antenna, key-ID
verification is performed with Intelligent Key using two-way communication, and if verification is success-
ful, an ignition rotation prohibition latch release signal is sent to steering lock unit. Steering lock unit
releases ignition knob rotation prohibition latch. (Ignition knob can now be turned.)
When it becomes possible to rotate the ignition knob, “KEY” warning lamp in combination meter lights up
green to notify driver that ignition knob can be turned.
NOTE:
When it becomes impossible to rotate the ignition knob, “KEY” warning lamp in combination meter lights
up red.
When key-ID verification is successful, Intelligent Key unit uses CAN communication to send engine start
permission signal to BCM.
When BCM receives engine start permission signal, it uses CAN communication to sent starter request
signal to IPDM E/R so that the engine will start when ignition knob is rotated to START position.
Operation Range
Engine can be started when Intelligent Key is in the vehicle. However, sometimes engine might not start when
Intelligent Key is on instrument panel, rear parcel shelf, trunk room or in glove box.
UnlockRemove mechanical key from ignition key cylinder (key switch: OFF)
Ignition knob is not press (ignition knob switch: OFF)
Trunk open
Remove mechanical key from ignition key cylinder (key switch: OFF)
Ignition knob is not press (ignition knob switch: OFF)
When trunk button pressed more than 0.5 seconds Remote controller button operation Operating condition
Vehicle operation Hazard lamp
Door unlocking operation Twice
Door locking operation Once
Remote keyless entry functions
Intelligent Key
Key switch
Ignition knob switch
Door unlock sensor
Door switch
Trunk room lamp switch
Door lock actuator
Trunk lid opener actuator
Intelligent Key unit
CAN communication system
BCM
Combination meter
Hazard warning lamp
Door lock function by the remote control button××××× × ×××
Trunk open function by the remote control button××× × ××××
Hazard reminder function (Door lock)×××××
Page 731 of 3502
INTELLIGENT KEY SYSTEM
BL-73
C
D
E
F
G
H
J
K
L
MA
B
BL
Active Check Function
Confirm whether or not ignition knob can be rotated by checking the color of warning lamp in combination
meter.
List of Operation Related Parts
Parts marked with × are the parts related to operation.
WARNING AND ALARM FUNCTION
Operation Description
The warnings and alarms are as follows and are given to the user as warning information and warnings using
combinations of Intelligent Key warning buzzer (in driver door and passenger door), inside vehicle buzzer (in
combination meter), and warning lamps “KEY” and “LOCK.”
Ignition switch return forgotten warning
With the ignition in OFF or ACC position, if the driver door is opened, this warning is issued.
Key left in ignition warning (when mechanical key used)
With the mechanical key in the ignition knob and the ignition switch is in the OFF, ACC, or LOCK position,
if the driver door is opened, this warning is issued.
Ignition switch OFF position warning (for inside car: when door closed)
This warning is issued when the user forgets to return the ignition knob to the LOCK position.
Ignition switch OFF position warning (for outside car: when door opened/closed)
This warning is issued when the user leaves the car without returning the ignition knob to the LOCK posi-
tion.
Warning for removal of Intelligent Key to outside the car (when door open/closed)
This warning is issued if the Intelligent Key is taken outside the car while the engine is running.
Warning for removal of Intelligent Key to outside the car (from window)
This warning is issued if the Intelligent Key is taken outside the car through a window while the engine is
running.
Door lock non-operation warning
This warning is issued if the door lock (lock) operation by a door request switch is not effected.
Intelligent Key low battery warning
This warning is issued when it is detected that the battery in the Intelligent Key has been used up.
Condition Operation
Ignition knob rotation possible “KEY” warning lamp in combination meter is lit up green.
Ignition knob rotation not possible “KEY” warning lamp in combination meter is lit up red.
Engine start functions
Intelligent Key
Key switch
Ignition knob switch
Inside key antenna
Intelligent Key unit
CAN communication system
BCM
Combination meter
IPDM E/R
NATS antenna amp.
Steering lock unit
Engine start function by the Intelligent Key××××××××× ×
Engine start function by the mechanical key× ×××××××
Active check function× ×××× ×
Page 732 of 3502
BL-74
INTELLIGENT KEY SYSTEM
Operation Condition
Warning and alarm names Operating conditions (when all the conditions below are met)
Ignition knob return forgotten warn-
ing
The ignition switch is in the ACC, OFF, or LOCK position (knob pressed)
The driver door is opened.
Ignition key warning
(When mechanical key used)
The mechanical key is inserted in the ignition knob (key switch: ON)
The ignition switch is in the ACC, OFF, or LOCK position.
The driver door is opened
Ignition knob OFF position warning
(for inside car: when door closed)
The ignition switch is in the OFF or LOCK position (knob pressed)
In the above state, when the ignition switch is changed from ON to OFF and 1 second
passes. (However, this warning is not issued if the mechanical key is inserted in the igni-
tion knob, ignition knob is turned except OFF position or ignition or ignition knob is not
pushed.)
Ignition knob OFF position warning
(for outside car: when door opened/
closed)
The ignition switch is in the OFF or LOCK position (knob pressed)
In the above state, when the ignition switch is changed from ON to OFF and 1 second
passes. (However, this warning is not issued if the mechanical key is inserted in the igni-
tion knob, ignition knob is turned except OFF position or ignition or ignition knob is not
pushed.)
Driver door open → closed
Warning for take out of Intelligent
Key to outside the car (when door
open/closed)
When Any of the Following Conditions Are Met
When the ignition knob is pressed in so that it can be rotated (or has been rotated), if any
of the doors has been opened, when all the doors are closed, the Intelligent Key unit
compares the key-ID with that of the Intelligent Key using the inside key antenna, if the
results of the comparison are NG (the Intelligent Key is not found)
When the ignition knob is pressed in so that it can be rotated (or has been rotated), if any
of the doors is open, the Intelligent Key unit compares the key-ID with that of the Intelli-
gent Key every 5 seconds using the inside key antenna, if the results of the comparison
are NG (the Intelligent Key is not found)
NOTE:
However, this warning is not issued if the mechanical key is inserted in the ignition knob.
Warning for take out of Intelligent
Key to outside the car (from win-
dow)When the ignition knob is pressed in so that it can be rotated (or has been rotated), if the
vehicle speed is less than 5 km per hour, the Intelligent Key unit compares the key-ID with
that of the Intelligent Key every 30 seconds using the inside key antenna, if the results of
the comparison are NG (the Intelligent Key is not found)
Note: The factory setting for this function is OFF.
Door lock non-operation warningWhen any of the following conditions are met
When the Intelligent Key is inside the car and the ignition knob is not pressed, when an
attempt is made to lock a door lock with a door request switch
NOTE:
This warning is issued even if the Intelligent Key is not in the out side key antenna detec-
tion area corresponding to the door request switch was operated.
When the ignition knob is pressed, when an attempt is made to lock a door lock with a
door request switch
NOTE:
This warning is only issued if the Intelligent Key is in the out side key antenna detection
area corresponding to the door request switch was operated.
When any of the doors is open, when an attempt is made to lock a door lock with a door
request switch
NOTE:
This warning is only issued if the Intelligent Key is in the out side key antenna detection
area corresponding to the door request switch was operated.
Intelligent Key low battery pre-
warningThis warning is issued when it is detected that the battery in the Intelligent Key has been
used up.
Page 733 of 3502
INTELLIGENT KEY SYSTEM
BL-75
C
D
E
F
G
H
J
K
L
MA
B
BL
Warning Procedure
List of Operation Related Parts
Parts marked with × are the parts related to operation.
Warning and alarm namesBuzzer Warning lamp
Inside car Outside car “KEY”
Ignition switch return forgotten warn-
ingBuzzer: Continuous — —
Ignition key warning
(When mechanical key used)Buzzer: Continuous — —
Ignition switch OFF position warning
(for inside car: when door closed)Buzzer: Twice — —
Ignition switch OFF position warning
(for outside car: when door opened/
closed)— Buzzer (3 times) —
Warning for removal of Intelligent Key
to outside the car (when door open/
closed)— Buzzer (3 seconds) Red illuminate
Warning for removal of Intelligent Key
to outside the car (from window)Buzzer (3 seconds) — Red illuminate
Door lock non-operation warning — Buzzer (2 seconds) —
Intelligent Key low battery pre-warning — —Green illuminate
(30 seconds after ignition switch
comes ON)
Warning and alarm functions
Intelligent Key
Key switch
Ignition knob switch
Intelligent Key unit ignition switch ACC position input signal
Intelligent Key unit ignition switch ON position input signal
Door switch
Door request switch
Door lock actuator
Inside key antenna
Outside key antenna (Driver, Passenger)
Outside key antenna (rear bumper)
Intelligent Key warning buzzer
Intelligent Key unit
CAN communication system
BCM
Combination meter
Ignition knob return forgotten warning (When Intelli-
gent Key used)××× ××××
Ignition key warning
(When mechanical key used)××× ××××
Ignition knob OFF position warning
(for outside car: when door closed)××× × ××××
Ignition knob OFF position warning
(for outside car: when door opened/closed)× ××× × ××××
Warning or take out of Intelligent Key to outside the
car
(when door open/closed)× × × × ×××××
Warning for take out of Intelligent Key to outside the
car (from window)× × × × ×××××
Page 734 of 3502
BL-76
INTELLIGENT KEY SYSTEM
CHANGE SETTINGS FUNCTION
The settings for each function can be changed with the CONSULT-II or Intelligent Key operation.
Changing Settings With the Intelligent Key
Intelligent Key remote controller button and door request switch operations change the engine startup function
settings (startup enabled/disabled) for each Intelligent Key independently.
Settings Change Procedure
1. With the ignition switch is in the LOCK position (ignition knob not pressed), hold down both the LOCK and
UNLOCK remote control buttons on the Intelligent Key at the same time for at least 10 seconds (The yard-
stick is that the Intelligent Key LED flashes 20 times.)
2. Within 5 seconds of releasing the Intelligent Key remote controller buttons, press the driver door request
switch.
3. The KEY warning lamp in combination meter lights up for 3 seconds (engine starting enabled → starting
disabled: lights up red, engine starting disabled → flashes green). This completes the settings change.
Changing Settings Using CONSULT-II
The settings for the Intelligent Key system functions can be changed using CONSULT-II (WORK SUPPORT).
Refer to BL-94, "
WORK SUPPORT" .
NOTE:
Once a function setting is changed, it will remain effective even if the battery is disconnected.
INTELLIGENT KEY REGISTRATION
Intelligent Key-ID registration is performed using the CONSULT-II. Up to 4 can be registered.
CAUTION:
After a new Intelligent Key-ID is registered, be sure to check the function.
When registering an additional Intelligent Key-ID, take any Intelligent Keys already registered and
Intelligent Keys for any other vehicles out of the vehicle before starting.
CONSULT-II can be used to check and delete Intelligent Key-IDs.
For future information, see the CONSULT-II Operation Manual NATS.
Door lock non-operation warning× × ××××××××××
Intelligent Key low battery warning×××××× Warning and alarm functions
Intelligent Key
Key switch
Ignition knob switch
Intelligent Key unit ignition switch ACC position input signal
Intelligent Key unit ignition switch ON position input signal
Door switch
Door request switch
Door lock actuator
Inside key antenna
Outside key antenna (Driver, Passenger)
Outside key antenna (rear bumper)
Intelligent Key warning buzzer
Intelligent Key unit
CAN communication system
BCM
Combination meter
Page 735 of 3502
INTELLIGENT KEY SYSTEM
BL-77
C
D
E
F
G
H
J
K
L
MA
B
BL
STEERING LOCK UNIT REGISTRATION
Steering Lock Unit ID Registration
CAUTION:
The method for registering a steering lock unit ID depends on the status of the steering lock unit
and Intelligent Key unit (new or old unit).
After registration is completed, press ignition knob with a portable unit in the vehicle so that it can
be rotated, and confirm that it cannot be rotated even when ignition switch is pressed without a
portable unit in the vehicle.
For future information, see the CONSULT-II Operation Manual NATS.
CAN Communication System DescriptionBIS000X0
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitBIS000X1
Refer to LAN-49, "CAN System Specification Chart" .
Page 746 of 3502
BL-88
INTELLIGENT KEY SYSTEM
Terminals and Reference Value for Intelligent Key UnitBIS000X4
Te r m i -
nalWire
ColorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Ignition
Knob
PositionOperation or Conditions
1L/YSteering lock unit
power supplyOutput LOCK — 5
2 L CAN-HInput/
Output—— —
3 P CAN-LInput/
Output—— —
4SBIntelligent Key warn-
ing buzzer (driver
side/trunk room)Output LOCKAny door open and
operate remote
controller button or
door request
switch.Buzzer
OFFBattery voltage
Sound
buzzer0
5B/WDoor request switch
(driver side)Input LOCKDoor request switch operation:
Press (ON).0
Other than the above (OFF) 5
6 G Ignition switch (ON) Input ON — Battery voltage
7 B/R key switch Input LOCKInsert mechanical key into igni-
tion key cylinder.Battery voltage
Remove mechanical key from
ignition key cylinder.0
11 Y/B Power source (Fuse) Input LOCK — Battery voltage
12 B Ground — ON — 0
13 V/WInside key antenna
(+)
(Trunk room)
Output LOCKAny door open → Close
(Door switch: ON → OFF)
14 W/LInside key antenna (-)
(Trunk room)
15 R/YInside key antenna
(+) signal
(Center console)
Output LOCKAny door open → Close (Door
switch: ON → OFF)
Ignition knob switch: ON (press
ignition knob.)
16 R/GInside key antenna (-)
signal
(Center console)
17 W/ROutside key antenna
(Rear bumper) (+)
Output LOCKTrunk opener request switch
operation (Switch: ON)
18 W/BOutside key antenna
(Rear bumper) (-)
19 POutside key antenna
(driver side) (+)
Output LOCKDriver door request signal opera-
tion (Switch: ON)
20 OOutside key antenna
(driver side) (-)
SIIA1910J
SIIA1910J
SIIA1910J
SIIA1910J
Page 748 of 3502
BL-90
INTELLIGENT KEY SYSTEM
Terminals and Reference Value for Steering Lock UnitBIS000X5
Terminals and Reference Value for BCMBIS000X6
Te r m i -
nalWire
ColorSignal DesignationSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Ignition
Knob
PositionOperation or Conditions
1 Y/B Battery power supply Input LOCK — Battery voltage
2L/YSteering lock unit power
supplyOutput LOCK — 5
3L/RSteering lock unit com-
munication signalInput/
OutputLOCKPress ignition knob with
Intelligent Key inside
vehicle.
Other than the above 5
4G/YSteering lock unit
ground—ON — 0
PIIB8449J
Te r m i -
nalWire
ColorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
12 R/LFront door switch (Passenger
side)Input Door open (ON) → Close (OFF) 0 → Battery voltage
13 R/B Rear door switch RH Input Door open (ON) → Close (OFF) 0 → Battery voltage
38 R Ignition switch InputIgnition switch is in ON or START posi-
tionBattery voltage
39 L CAN-HInput/
Output——
40 P CAN-LInput/
Output——
42 Y/R Battery power supply (Fuse) Input — Battery voltage
52 B Ground — — 0
55 W/BBattery power supply (Fusible
link)Input — Battery voltage
57 V/W Trunk room lamp switch Input Trunk lid open (ON) → Close (OFF) 0 → Battery voltage
62 SB Front door switch (Driver side) Input Door open (ON) → Close (OFF) 0 → Battery voltage
63 R/W Rear door switch LH Input Door open (ON) → Close (OFF) 0 → Battery voltage
Page 751 of 3502
INTELLIGENT KEY SYSTEM
BL-93
C
D
E
F
G
H
J
K
L
MA
B
BL
CONSULT-II Functions (INTELLIGENT KEY)BIS001TD
CONSULT-II can display each diagnostic item using the diagnostic test modes as shown below.
CONSULT-II Inspection ProcedureBIS001TE
CAUTION:
If CONSULT-II is used with no connection CONSULT-II CONVERTER, malfunctions might be detected
in self-diagnosis depending on control unit which performs CAN Communication.
BASIC OPERATION
Refer to GI-34, "CONSULT-II Start Procedure" .
CONSULT-II Application ItemsBIS001TF
SELF-DIAGNOSTIC RESULTS
*: It is possible to display it only with the program card for engine immobilizer system.
DATA MONITOR
Part to be diagnosed Test item, Diagnosis mode Description
Intelligent KeyWORK SUPPORT Changes settings for each function.
SELF-DIAG RESULTS Intelligent Key unit performs CAN communication diagnosis.
DATA MONITOR Displays Intelligent Key unit input data in real time.
CAN DIAGNOSTIC SUPPORT
MONITORThe results of transmit/receive diagnosis of CAN Communication can
be read.
ACTIVE TESTOperation of electrical loads can be checked by sending driving signal
to then.
ECU PART NUMBER Displays Intelligent Key unit part No.
DTC Self-diag results Description Diagnosis procedureReference
page
U1000 CAN COMM CIRCUITMalfunction is detected in CAN communica-
tion.Check CAN communica-
tion system.BL-100
U1010 CONTROL UNIT (CAN) Intelligent Key unit internal malfunctionCheck CAN communica-
tion system.BL-100
B2013*STRG COMM CIRCUITMalfunction is detected in communication of
Intelligent Key unit and steering lock unit.Check steering lock unit.BL-115
B2552*INTELLIGENT KEY Intelligent Key unit internal malfunctionReplace Intelligent Key
unit.BL-117
B2590*DISCORD BCM - I-KEY Malfunction is detected in immobilizer system. Check NATS.BL-139
Monitor item Content
PUSH SW Indicates [ON/OFF] condition of ignition knob switch.
KEY SW Indicates [ON/OFF] condition of key switch.
DR REQ SW Indicates [ON/OFF] condition of door request switch (driver side).
AS REQ SW Indicates [ON/OFF] condition of door request switch (passenger side).
BD/TR REQ SW Indicates [ON/OFF] condition of trunk opener request switch.
IGN SW Indicates [ON/OFF] condition of ignition switch in ON position.
ACC SW Indicates [ON/OFF] condition of ignition switch in ACC position.
DOOR STAT SW Indicates [ON/OFF] condition of stop lamp switch.
STOP LAMP SW Indicates [ON/OFF] condition of door unlock sensor.
P RANGE SW* Indicates [ON/OFF] condition of park position switch.
DOOR LOCK SIG* Indicates [ON/OFF] condition of door lock signal from Intelligent Key remote controller button.
DOOR UNLOCK SIG* Indicates [ON/OFF] condition of door unlock signal from Intelligent Key remote controller button.
KEYLESS TRUNK* Indicates [ON/OFF] condition of trunk open signal from Intelligent Key remote controller button.