instrument panel NISSAN TEANA 2003 User Guide

ATC-124
AIR MIX DOOR MOTOR

AIR MIX DOOR MOTOR PFP:27732
Removal and InstallationBJS000HK
REMOVAL
Driver Side
1. Set the temperature (driver side) at 18°C, and then disconnect the battery cable from the negative termi-
nal.
2. Remove instrument driver lower panel. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
3. Remove aspirator.
4. Remove mounting screws, and then remove air mix door motor.
5. Disconnect air mix door motor connector.
Passenger Side
1. Set the temperature (passenger side) at 18°C, and then disconnect the battery cable from the negative
terminal.
2. Remove blower unit. Refer to AT C - 11 3 , "
BLOWER UNIT" .
3. Remove mounting screws, and then remove air mix door motor.
4. Disconnect air mix door motor connector.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA3307E
RJIA3308E

ATC-126
DUCTS AND GRILLES

DUCTS AND GRILLESPFP:27860
Removal and InstallationBJS000HM
REMOVAL
Removal of Center Ventilator Grilles
1. Remove cluster lid D. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove mounting clips, and then remove center ventilator
grilles.
1. Defroster nozzle 2. Duct assembly 3. Instrument panel
4. Side defroster grille (left) 5. Side ventilator grille (left) 6. Center ventilator grille (left)
7. Center ventilator grille (right) 8. Side ventilator grille (right) 9. Side defroster grille (right)
SJIA1653E
RJIA2209E

DUCTS AND GRILLES
ATC-127
C
D
E
F
G
H
I
K
L
MA
B
AT C

Removal of Side Ventilator Grilles
1. Remove instrument passenger upper panel. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove mounting clips, and then remove side ventilator grille
(right).
3. Remove cluster lid A. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
4. Remove mounting clips, and then remove side ventilator grille
(left).
Removal of Rear Ventilator Grille
1. Remove console rear cover. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove mounting clips, and then remove rear ventilator grille.
RJIA3311E
RJIA3312E
RJIA2212E

ATC-128
DUCTS AND GRILLES

Removal of Defroster Nozzle and Duct Assembly
1. Remove instrument panel assembly. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove mounting screws, and then remove defroster nozzle.
3. Remove mounting screws, and then remove duct assembly.
Removal of Side Defroster Grilles
1. Remove duct assembly.
2. Remove side defroster grilles.
RJIA3313E
RJIA3314E

DUCTS AND GRILLES
ATC-129
C
D
E
F
G
H
I
K
L
MA
B
AT C

Removal of Rear Ventilator Ducts
1. Remove center console. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove mounting clips, and then remove rear ventilator duct 2.
3. Remove mounting clips and screw, and then remove rear venti-
lator duct 1.
Removal of Foot Ducts
1. Remove instrument driver lower panel. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove instrument lower cover (driver side)
3. Remove mounting screws, and then remove foot duct (left).
4. Remove blower unit. Refer to AT C - 11 3 , "
BLOWER UNIT" .
5. Remove intake sensor connector from foot duct.
6. Remove mounting screws, and then remove foot duct (right).
RJIA3315E
RJIA3316E
RJIA3317E
RJIA3318E

ATC-130
DUCTS AND GRILLES

Removal of Floor Ducts
1. Remove front seats and center console. Refer to SE-97, "FRONT SEAT" and IP-10, "INSTRUMENT
PANEL ASSEMBLY" .
2. Slide front floor duct downward, and then remove it.
3. Remove floor carpet. Refer to EI-52, "
FLOOR TRIM" .
4. Remove mounting clips, and then remove floor ducts.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA3319E
RJIA3320E

AUDIO (WITH INTEGRATED DISPLAY SYSTEM)
AV-15
C
D
E
F
G
H
I
J
L
MA
B
AV

Removal and Installation of Audio UnitBKS0020Z
REMOVAL
1. Remove instrument panel finishers (C, D). Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove screws (4) and remove audio unit integral with A/C and
AV switch.
3. Remove screws (4).
1. Screw 2. Bracket (LH) 3. A/C and AV switch
4. Audio unit 5. Bracket (RH) 6. Screw
7. Screw 8. Screws 9. Screw
10. Unified meter and A/C amp.
SKIA8645E
SKIB0873E
SKIB0874E

AV-34
AUDIO (WITH INTEGRATED COLOR DISPLAY SYSTEM)

Removal and Installation of Audio UnitBKS0028W
REMOVAL
1. Remove instrument panel finishers (C, D). Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove screws (4) and remove audio unit integral with A/C and
AV switch.
3. Remove screws (4).
1. Display control unit 2. Screws 3. Bracket (LH)
4. A/C and AV switch 5. Audio unit 6. Bracket (RH)
7. Screws 8. Screws 9. Screws
10. Screws 11. Screws 12. Unified meter and A/C amp.
SKIB0872E
SKIB0873E
SKIB0874E

AV-36
AUDIO (WITH INTEGRATED COLOR DISPLAY SYSTEM)

Removal and Installation of Rear Audio Control SwitchBKS002CZ
REMOVAL
1. Remove tray box from the center armrest. Refer to SE-117, "Removal and Installation of Seatback" .
2. Disconnect connector.
3. Push pawl on reverse side and remove the rear audio control
switch.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of CD Auto ChangerBKS0028X
REMOVAL
1. Remove passenger instrument panel (lower). Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove screws (4) and disconnect connector, and remove CD
auto changer.
3. Remove screws (4) and remove bracket.
INSTALLATION
Installation is the reverse order of removal.
SKIB1365E
SKIB0880E
SKIB0881E

AV-60
INTEGRATED DISPLAY SYSTEM

Removal and Installation of Display UnitBKS0022K
REMOVAL
1. Remove cluster lid D. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove screws (4), and remove display unit.
3. Remove screws (4) and nylon washers (4), and then remove
display finisher.
4. Remove screws (4), and remove bracket.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of A/C and AV SwitchBKS0022L
REMOVAL
Remove A/C and AV switch integral with audio unit. Refer to AV- 1 5 , "Removal and Installation of Audio Unit" .
INSTALLATION
Installation is the reverse order of removal.
SKIA6307E
SKIA6779E