mirror NISSAN TEANA 2003 Owner's Manual

GW-78
DOOR MIRROR

Disassembly and AssemblyBIS0010J
DISASSEMBLY
1. Pull out all the terminals from the connector.
NOTE:
Before pulling out the terminal, note the connector terminal arrangement.
2. Place the mirror body with mirror glass facing upward.
3. Put a strip of protective tape B on mirror body.
4. As shown in the figure, insert a small slotted screwdriver A into
the recess between mirror base (mirror holder)(1) and mirror
holder bracket (2) and push up two pawls (3) to remove mirror
holder lower half side.
NOTE:
Insert screwdriver into recesses, and push up while rotating
(twist) to make work easier.
CAUTION:
When pushing up the tabs, do not forcibly push up only 1
concave but try to push up using 2 concave positions.
5. Remove terminals of mirror heater attachment.
6. Remove base.
7. Remove door mirror actuator.
8. Remove power unit mounting screws, and disconnect connector.
1. Housing 2. Door mirror actuator 3. Power unit
4. Mirror body (with holder) 5. Connector 6. Base
7. Mirror body cover 8. Door mirror actuator mounting screw 9. Base mounting screw
PIIB1023E
PIIB8320J

DOOR MIRROR
GW-79
C
D
E
F
G
H
J
K
L
MA
B
GW

9. Separate the power unit from the door mirror actuator.
ASSEMBLY
1. Connect power unit connector, and install power unit to door mirror actuator.
2. Install door mirror actuator assembly and base to the housing.
3. Set power unit and mirror body assembly in a horizontal position.
4. Warm the lower tabs with a dryer or equivalent.
NOTE:
Warm the lower tabs sufficiently before installing the mirror body. The tabs may be broken if it is cold. Be
careful especially in winter.
5. Engage upper tabs of mirror glass with power unit. Then, press
lower part of mirror glass down until the lower part snaps to
allow engagement of lower tabs.
NOTE:
After installation, visually check that the lower tabs are securely
engaged when viewed from the bottom of mirror surface.
6. Insert the harness terminals into the connector.
NOTE:
Make sure to insert the harness terminals into the correct con-
nector. Do not confuse the locations.
PIIA6332E

GW-80
INSIDE MIRROR

INSIDE MIRRORPFP:96321
Removal and InstallationBIS0010K
REMOVAL
Slide the mirror upward to remove.
INSTALLATION
Install in the reverse order of removal.
1. Inside mirror
PIIA6795E

IDX-2
ALPHABETICAL INDEX
Numerics
3rd position switch ............................. AT-161
, AT-210
A
A/C air flow ...................................................... ATC-31
A/C component layout ..................................... ATC-20
A/C compressor clutch removal and installation ...........
ATC-136
A/C compressor mounting ............................. ATC-134
A/C compressor precaution ............................. ATC-11
A/C compressor special service tool ................ ATC-15
A/C control operation (auto A/C) ...................... ATC-29
A/C diagnostic work flow (auto A/C) ................ ATC-94
A/C evaporator ............................................... ATC-144
A/C HFC134a (R134a) system precaution ........ ATC-5
A/C HFC134a (R134a) system service procedure .......
ATC-131
A/C HFC134a (R134a) system service tools ... ATC-16
A/C HFC134a system service equipment precaution ...
ATC-12
A/C lubricant (R134a) ...................................... ATC-21
A/C lubrication oil ........................................... ATC-150
A/C operational check ...................................... ATC-54
A/C self-diagnoses (auto A/C) .......... ATC-46, ATC-94
A/C service data specification ........................ ATC-150
A/C system description (auto A/C) ................... ATC-24
A/C, A - Wiring diagram ................................... ATC-39
A/T fluid checking .................................. AT-14, MA-35
A/T fluid replacement ............................. AT-15, MA-36
A/T IND - Wiring diagram .................................... DI-48
A/T shift control system ................................... AT-213
A/T shift lock system ........................................ AT-216
A/T shift lock system - Wiring diagram ............ AT-217
A/T trouble diagnoses ........................................ AT-34
Accelerator control system ............................... ACC-3
Accelerator pedal position (APP) sensor ........ EC-251,
EC-258
, EC-272, EC-631, EC-638, EC-652
Accelerator pedal released position learning .... EC-47,
EC-389
AFS ..................................................................... LT-75
AFS - Wiring diagram ......................................... LT-79
Air bag .............................................................. SRS-3
Air bag disposal .............................................. SRS-48
Air bag precautions ........................................... SRS-3
Air cleaner and air duct(QR20DE) .................... EM-17
Air cleaner and air duct(VQ23DE and VQ35DE) ..........
EM-131
Air cleaner filter replacement(QR20DE) ........... MA-20
Air cleaner filter replacement(VQ23DE and VQ35DE) .
MA-30
Air cleaner filter(QR20DE) ................................ EM-17
Air cleaner filter(VQ23DE and VQ35DE) ........ EM-132
Air conditioner cut control .................... EC-25, EC-362
Air flow meter - See Mass air flow sensor ...... EC-124,
EC-466
Air mix. door motor ......................... ATC-66, ATC-124
Ambient sensor ............................... ATC-96, ATC-109
Angular tightening application(QR20DE) ............ EM-6
Angular tightening application(VQ23DE and VQ35DE)
EM-120
Antenna ............................................................. AV-38
APPS1 - Wiring diagram ................... EC-253, EC-633
APPS2 - Wiring diagram ................... EC-260, EC-640
APPS3 - Wiring diagram ................... EC-274, EC-654
ASC/BS - Wiring diagram ................................ EC-605
ASC/SW - Wiring diagram ............................... EC-597
ASCBOF - Wiring diagram ............................... EC-661
ASCD ............................................................... EC-363
ASCD (automatic speed control device) ........... ACS-2
ASCD brake switch ........................... EC-602, EC-660
ASCD indicator lamp ....................................... EC-667
ASCD steering switch ...................................... EC-595
ASCIND - Wiring diagram ................................ EC-668
AT indicator lamp ................................................ DI-48
Audio ........................................................ AV-4, AV-18
AUDIO - Wiring diagram .......................... AV-7, AV-21
Auto air conditioner - Wiring diagram ............. ATC-39
Auto amp ...................................................... ATC-108
Auto anti-dazzling inside mirror ....................... GW-80
Automatic amplifier ........... ATC-44, ATC-56, ATC-108
AV communication line .......................... AV-49, AV-73
Axle ................................................................... MA-42
B
BA/FTS - Wiring diagram ................................. AT-111
BACK/L - Wiring diagram ................................. LT-193
Back-up lamp ................................................... LT-193
Basic inspection .................................. EC-40, EC-381
Battery ................................................................. SC-4
BCM (Body control module) .............................. BCS-3
Blower motor ................................... ATC-72, ATC-115
Blower unit .................................................... ATC-113
Boring/horning cylinder block(QR20DE) ......... EM-104
Boring/horning cylinder block(VQ23DE and VQ35DE) .
EM-250
Brake fluid level ................................................ MA-40
Brake hydraulic line ........................................... BR-11
Brake inspection ............................................... MA-41
Brake lines and cables inspection .................... MA-40
Brake pedal .......................................................... BR-6
Brake switch ......... EC-245, EC-602, EC-626, EC-660
BRK/SW - Wiring diagram ................ EC-247, EC-627
Bulb specifications ........................................... LT-261
Bumper, front ...................................................... EI-14
Bumper, rear ....................................................... EI-17
C
Camshaft inspection(QR20DE) ........................ EM-44
Camshaft inspection(VQ23DE and VQ35DE) EM-194
Camshaft position sensor (PHASE) .. EC-176, EC-524
Camshaft(QR20DE) .......................................... EM-41
Camshaft(VQ23DE and VQ35DE) .................. EM-192
CAN - Wiring diagram ......... EC-114, EC-459, AT-134,
CVT-54

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
CAN (Controller Area Network) . BL-23, BL-48, BL-77,
GW-56
, SE-16
CAN communication EC-113, EC-458, AT-27, CVT-19,
CVT-53
, BL-23, BL-48, BL-77, GW-56, SE-16, WW-9
Canister-See EVAP canister ............... EC-29, EC-369
CHARGE - Wiring diagram ................................ SC-28
Charging system ................................................ SC-27
Chassis and body maintenance ........................ MA-35
CHIME - Wiring diagram ..................................... DI-60
CIGAR - Wiring diagram .................................. WW-60
Cigarette lighter ............................................... WW-60
Circuit breaker ................................................... PG-16
Closed loop control .............................. EC-22, EC-359
Collision diagnosis ........................................... SRS-55
Combination meter ............................................... DI-4
COMM - Wiring diagram ........................ AV-49, AV-73
Component Location (auto A/C) ...................... ATC-36
Compression pressure(QR20DE) ...................... EM-65
Compression pressure(VQ23DE and VQ35DE) ...........
EM-210
Compressor clutch removal and installation .. ATC-136
Compressor special service tool ...................... ATC-15
Condenser ..................................................... ATC-142
Connecting rod bearing clearance(QR20DE) .. EM-105
Connecting rod bearing clearance(VQ23DE and
VQ35DE) ......................................................... EM-251
Connecting rod bushing clearance(QR20DE) . EM-101
Connecting rod bushing clearance(VQ23DE and
VQ35DE) ......................................................... EM-247
Connecting rod(QR20DE) ............................... EM-101
Connecting rod(VQ23DE and VQ35DE) ......... EM-247
CONSULT-II for engine ....................... EC-80, EC-425
CONSULT-II Reference value (CVT) .............. CVT-43
Control units (terminal arrangement) ................. PG-74
Control valve (CVT) ......................................... CVT-23
Controller Area Network (CAN) . BL-23, BL-48, BL-77,
GW-56
, SE-16
Converter housing installation ............ AT-244, AT-355
COOL/F - Wiring diagram .................. EC-222, EC-579
Coolant mixture ratio ......................................... MA-15
Coolant replacement(QR20DE) ......................... MA-16
Coolant replacementVQ35DE ........................... MA-25
Cooling circuit (engine)(QR20DE) ....................... CO-8
Cooling circuit (engine)(VQ32DE and VQ35DE) CO-32
Cooling fan control ........................................... EC-575
Cooling fan motor ............................................ EC-575
Cooling fan relay .............................................. EC-575
Cooling fan(QR20DE) ........................................ CO-20
Cooling fan(VQ23DE and VQ35DE) .................. CO-44
Cowl top ............................................................... EI-21
Cowl top cover ..................................................... EI-21
Crankcase ventilation system - See Positive crankcase
ventilation ............................................ EC-30
, EC-370
Crankshaft position sensor (POS) ..... EC-169, EC-517
Crankshaft(QR20DE) ...................................... EM-104
Crankshaft(VQ23DE and VQ35DE) ................ EM-251
Crash zone sensor .......................................... SRS-44
CVT air breather hose ................................... CVT-186
CVT control system ......................................... CVT-16
CVT cross-sectional view ................................ CVT-15
CVT Electrical parts location ............................ CVT-30
CVT fluid checking ................ CVT-13, CVT-32, MA-36
CVT Fluid Cooler ........................................... CVT-189
CVT fluid replacement ........................ CVT-14, MA-38
CVT fluid temparature sensor .......................... CVT-69
CVT hydraulic control system .......................... CVT-17
CVT indicator ...................................................... DI-52
CVT self-diagnoses ......................................... CVT-47
CVT shift lock system .................................... CVT-180
CVT trouble diagnoses .................................... CVT-24
CVTIND - Wiring diagram ................................... DI-52
Cylinder block boring(QR20DE) ..................... EM-104
Cylinder block(QR20DE) .................................. EM-81
Cylinder block(VQ23DE and VQ35DE) .......... EM-228
Cylinder head bolt tightening(QR20DE) ........... EM-68
Cylinder head bolt tightening(VQ23DE and VQ35DE) .
EM-213
Cylinder head(QR20DE) ................................... EM-65
Cylinder head(VQ23DE and VQ35DE) ........... EM-210
D
D/LOCK - Wiring diagram .................................. BL-25
Diagnosis sensor unit ..................................... SRS-47
Diagnostic trouble code (DTC) for OBD system EC-10,
EC-34
, EC-347, EC-375
Diagnostic trouble code (DTC) inspection priority chart
EC-58
, EC-400, CVT-24
Differentil side oil seal .................................... CVT-187
Display and amp.assembly ............... ATC-44, ATC-56
Display Control Unit ........................................... AV-61
Display Unit ........................................................ AV-41
Door glass ........................................... GW-46, GW-50
Door glass Fitting Adjustment(Front) ................ GW-49
Door glass Fitting Adjustment(Rear) ................. GW-53
Door lock .......................................................... BL-123
Door mirror .......................................... GW-74, GW-77
Door trim ............................................................. EI-35
Door, front ........................................... BL-119, GW-46
Door, rear ............................................ BL-119, GW-50
Drive belt inspection(QR20DE) ......................... MA-16
Drive belt inspection(VQ23DE and VQ35DE) ... MA-24
Drive belt(QR20DE) .......................................... EM-14
Drive belt(VQ23DE and VQ35DE) .................. EM-128
Drive shaft ......................................................... MA-43
Driver air bag .................................................. SRS-35
Dropping resistor (A/T) .................................... AT-132
Duct and grilles .............................................. ATC-126
E
ECM input/output signal ....................... EC-72
, EC-415
ECM power supply EC-106, EC-193, EC-451, EC-541
ECM/PW - Wiring diagram ................. EC-194, EC-542
ECTS - Wiring diagram ...................... EC-133, EC-476
Electric sunroof .................................................. RF-10
Electric throttle control actuator ........ EC-197, EC-200,
EC-213
, EC-552, EC-555

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Heated oxygen sensor 1 (bank 2) .... EC-486, EC-496,
EC-696
Heated oxygen sensor 1 heater ...................... EC-308
Heated oxygen sensor 1 heater (bank 1) ........ EC-706
Heated oxygen sensor 1 heater (bank 2) ........ EC-706
Heated oxygen sensor 2 .................................. EC-313
Heated oxygen sensor 2 (bank 1) ..... EC-714, EC-723
Heated oxygen sensor 2 (bank 2) ..... EC-714, EC-723
Heated oxygen sensor 2 heater ...................... EC-319
Heated seat ....................................................... SE-61
Heater and cooling unit (Heater core) ........... ATC-119
HFC134a (R134a) system precaution ............... ATC-5
HFC134a (R134a) system service procedure ATC-131
HFC134a (R134a) system service tools .......... ATC-16
HFC134a system service equipment precaution ..........
ATC-12
HLC - Wiring diagram ...................................... WW-43
HO2S1 - Wiring diaram ..................... EC-145, EC-152
Horn ................................................................. WW-62
HORN - Wiring diagram ................................... WW-62
How to erase DTC for OBD system ..... EC-35, EC-376
HSEAT - Wiring diagram ................................... SE-70
I
IATSEN - Wiring diagram .................. EC-325
, EC-731
Idle air volume learning ....................... EC-47, EC-389
Idle speed .............................. EC-40, EC-381, EC-387
Ignition coil ......................................... EC-329, EC-735
Ignition coil(QR20DE) ........................................ EM-31
Ignition coil(VQ23DE and VQ35DE) ................ EM-152
Ignition control system ....................... EC-329, EC-735
Ignition timing ........................ EC-40, EC-381, EC-387
IGNSYS - Wiring diagram .................. EC-330, EC-736
In vehicle sensor ............................. ATC-99, ATC-110
INF/D - Wring diagram ........................... AV-43, AV-65
INJECT - Wiring diagram ................... EC-290, EC-685
Injector ............................................... EC-289, EC-684
Input/Output signal of TCM .............................. CVT-19
Instrument panel .................................................. IP-10
INT/L - Wiring diagram ..................................... LT-217
Intake air temperature sensor ............ EC-324, EC-730
Intake door control linkage adjustment ............ ATC-71
Intake door motor ........................... ATC-69, ATC-117
Intake manifold collector(VQ23DE and VQ35DE) ........
EM-133
Intake manifold(QR20DE) ................................. EM-19
Intake manifold(VQ23DE and VQ35DE) ......... EM-138
Intake sensor ................................ ATC-105, ATC-112
Intake valve timing control ............................... EC-116
Intake valve timing control (Bank 1) ................ EC-461
Intake valve timing control (Bank 2) ................ EC-461
Intake valve timing control solenoid valve (Bank 1) ......
EC-545
Intake valve timing control solenoid valve (Bank 2) ......
EC-545
Interior ................................................................. EI-38
Interior lamp ........................................ LT-217, LT-219
IPDM (Intelligent power distribution module engine room) ................................................................. PG-17
IVC - Wiring diagram ....................................... EC-119
IVCB1 - Wiring diagram ................................... EC-546
IVCB2 - Wiring diagram ................................... EC-548
K
Knock sensor (KS) ............................. EC-164
, EC-512
KS - Wiring diagram ........................... EC-165, EC-513
L
L/USSV - Wiring diagram ............................... CVT-148
LAN system circuit ........................................... ATC-59
LCD display ....................................................... AV-61
Line pressure and secondary pressure control CVT-20
Line pressure solenoid valve .......... CVT-97, CVT-102
Line pressure test (A/T) ..................................... AT-46
Liquid gasket application(QR20DE) ........... EM-6, LU-3
Liquid gasket application(VQ23DE and VQ35DE) ........
EM-120
, LU-15, CO-3, CO-27
Location of electrical units ................................. PG-67
Lock-up and select control ............................... CVT-21
Lock-up select solenoid valve ........................ CVT-147
LPSV - Wiring diagram ...................... AT-127, CVT-98
Lubricant (R134a) A/C ..................................... ATC-21
Lubricants ......................................................... MA-14
Lubrication circuit (engine)(QR20DE) .................. LU-5
Lubrication circuit (engine)(VQ23DE and VQ35DE) .....
LU-17
Lubrication oil A/C .......................................... ATC-150
M
MAFS - Wiring diagram ..................... EC-126
, EC-468
Magnet clutch ................................. ATC-78, ATC-136
MAIN - Wiring diagram ........ EC-106, EC-451, AT-158
Maintenance (engine)(VQ23DE and VQ35DE) MA-24
Malfunction indicator (MI) .................... EC-36, EC-377
Mass air flow sensor (MAFS) ............. EC-124, EC-466
Meter ..................................................................... DI-4
METER - Wiring diagram .................................... DI-10
MIL data link connectors circuit ......... EC-344, EC-763
MIL/DL - Wiring diagram .................... EC-344, EC-763
Mirror, door ......................................... GW-74, GW-77
Mirror, out side .................................... GW-74, GW-77
MMSW - Wiring diagram ................................ CVT-114
Mode door control linkage adjustment ............. ATC-65
Mode door motor ............................ ATC-63, ATC-123
Molding - See Exterior EI-25, EI-27, EI-28, EI-29, EI-30
Mud guard - See Exterior .................................... EI-24
Multiport fuel injection (MFI) system .... EC-21, EC-358
Multiport fuel injection precautions ....................... GI-6
N
NATS - Wiring diagram .................................... BL-143
NATS (Nissan anti-theft system) precautions ....... GI-3
NONDTC - Wiring diagram .............. AT-168, CVT-160

IDX-6
ALPHABETICAL INDEX
NVH troubleshooting (BR) ................................... BR-5
NVH troubleshooting (EM)(QR20DE) ............... EM-12
NVH troubleshooting (EM)(VQ23DE and VQ35DE) .....
EM-126
O
O2S1B1 - Wiring diagram .................. EC-488
, EC-498
O2S1B2 - Wiring diagram .................. EC-490, EC-500
Oil cooler (engine)(VQ23DE and VQ35DE) ....... LU-23
Oil filter(QR20DE) .............................................. LU-10
Oil filter(VQ23DE and VQ35DE) ........................ LU-22
Oil pan (engine)(QR20DE) ............................... EM-26
Oil pan (engine)(VQ23DE and VQ35DE) ....... EM-145
Oil pressure (engine)(QR20DE) .......................... LU-7
Oil pressure (engine)(VQ23DE and VQ35DE) .. LU-20
Oil pump (engine)(QR20DE) ............................. LU-11
Oil pump (engine)(VQ23DE and VQ35DE) ....... LU-25
Oil pump regulator valve (engine)(QR20DE) ..... LU-11
Oil pump regulator valve (engine)(VQ23DE and
VQ35DE) ........................................................... LU-25
Oil seal replacement (engine)(QR20DE) ......... EM-53,
EM-62
, EM-70, EM-81
Oil seal replacement (engine)(VQ23DE and VQ35DE)
EM-207
On board diagnostic system ................ EC-33, EC-373
Out side mirror .................................... GW-74, GW-77
Overheat ............................................ EC-218, EC-575
Oversize piston(QR20DE) .............................. EM-103
Oversize piston(VQ23DE and VQ35DE) ........ EM-249
OVRCSV - Wiring diagram .............................. AT-101
P
Park/Neutral position switch .............. EC-238
, EC-614
Park/neutral position switch (A/T) ...... AT-161, AT-210
Park/neutral position switch (CVT) .................. CVT-62
PCV (positive crankcase ventilation) ... EC-30, EC-370
PHASE - Wiring diagram ................................. EC-178
PHSB1 - Wiring diagram .................................. EC-526
PHSB2 - Wiring diagram .................................. EC-528
Pilot bushing replacement - See Pilot
converter(QR20DE) .......................................... EM-81
Pilot bushing replacement - See Pilot
converter(VQ23DE and VQ35DE) .................. EM-228
Piston assembly(QR20DE) ............................... EM-92
Piston assembly(VQ23DE and VQ35DE) ....... EM-240
Piston pin inspection(QR20DE) ........................ EM-99
Piston pin inspection(VQ23DE and VQ35DE) EM-245
Piston ring inspection(QR20DE) ..................... EM-100
Piston ring inspection(VQ23DE and VQ35DE) EM-246
Piston to bore clearance(QR20DE) ................ EM-103
Piston to bore clearance(VQ23DE and VQ35DE) ........
EM-249
PNP/SW - Wiring diagram .. EC-239, EC-615, CVT-64
POS - Wiring diagram ........................ EC-171, EC-519
POWER - Wiring diagram ................... CVT-135, PG-4
Power door mirror .............................................. BL-21
Power seat ......................................................... SE-59
Power steering fluid level .................................. MA-42
Power steering gear ........................................... PS-17
Power steering oil pump .................................... PS-29
Power steering pressure (PSP) sensor .......... EC-185,
EC-533
Power supply routing .......................................... PG-3
Power window .................................................. GW-17
Precations for Leak detection dye .................. ATC-14
Precautions (General) ........................................... GI-4
Pressure control solenoid valve A .. CVT-97, CVT-102
Pressure control solenoid valve B CVT-105, CVT-108
Pressure test (CVT) ........................................ CVT-33
PRGVLV - Wirng diagram ................. EC-283, EC-678
Primary pressure sensor ............................... CVT-126
Primary Speed Sensor .................................... CVT-74
PRIPS - Wiring diagram ................................ CVT-127
PRSCVT - Wiring diagram .............................. CVT-75
PS/SEN - Wiring diagram ................. EC-186, EC-534
PT/SEN - Wiring diagram ................................ AT-121
R
R/FOG - Wiring diagram .................................. LT-144
Radiator(QR20DE) ............................... CO-13, CO-16
Radiator(VQ23DE and VQ35DE) ..................... CO-37
Radio - See Audio .................................... AV-4, AV-18
Rear bumper ....................................................... EI-17
Rear disc brake .................................................. BR-33
Rear door ............................................ BL-119, GW-50
Rear parcel shelf finisher .................................... EI-43
Rear seat ......................................................... SE-112
Rear window defogger ..................................... GW-54
Refrigerant connection precaution .................... ATC-6
Refrigerant discharging evacuating charging ATC-131
Refrigerant general precaution ......................... ATC-6
Refrigerant lines ............................................ ATC-131
Refrigerant pressure sensor EC-339, EC-748, ATC-83,
ATC-144
Refrigeration cycle .......................................... ATC-19
Removal and installation (A/T) ......................... AT-241
Road test ......... AT-48, AT-50, AT-51, AT-52, CVT-35
Rocker cover(QR20DE) .................................... EM-39
Rocker cover(VQ23DE and VQ35DE) ............ EM-160
Room lamp - See Interior lamp ........................ LT-219
ROOM/L - Wiring diagram ............................... LT-225
RP/SEN - Wiring diagram ................. EC-340, EC-749
RRO2 - Wiring diagram .................... EC-314, EC-320
RRO2B1 - Wiring diagram ................ EC-715, EC-724
RRO2B2 - Wiring diagram ................ EC-717, EC-726
S
SEAT - Wiring diagram ...................................... SE-59
Seat belt pre-tensioner disposal ..................... SRS-48
Seat belt, front ..................................................... SB-3
Seat, rear ......................................................... SE-112
Secondary pressure sensor .......................... CVT-118
Secondary Speed Sensor ............................... CVT-79
SECPS - Wiring diagram .............................. CVT-119

LT-4 Wiring Diagram — STOP/L — ..............................190
WITH REAR SUNSHADE AND REAR VIEW
CAMERA ...........................................................190
WITHOUT REAR SUNSHADE AND REAR VIEW
CAMERA ...........................................................191
Bulb Replacement ................................................192
HIGH-MOUNTED STOP LAMP .........................192
STOP LAMP ......................................................192
Removal and Installation ......................................192
HIGH-MOUNTED STOP LAMP .........................192
STOP LAMP ......................................................192
BACK-UP LAMP .....................................................193
Wiring Diagram — BACK/L — ..............................193
WITH A/T ...........................................................193
WITH CVT .........................................................194
Bulb Replacement ................................................195
Removal and Installation ......................................195
PARKING, LICENSE PLATE AND TAIL LAMPS ....196
Component Parts and Harness Connector Location .196
System Description ...............................................196
OUTLINE ...........................................................196
PARKING, LICENCE PLATE AND TAIL LAMPS
OPERATION ......................................................197
COMBINATION SWITCH READING FUNCTION .197
EXTERIOR LAMP BATTERY SAVER CONTROL .197
CAN Communication System Description ............198
CAN Communication Unit .....................................198
Schematic .............................................................199
Wiring Diagram — TAIL/L — ................................200
Terminals and Reference Values for BCM ............205
Terminals and Reference Values for IPDM E/R ....206
How to Perform Trouble Diagnoses ......................206
Preliminary Check ................................................206
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................206
CONSULT-II Functions (BCM) ..............................207
CONSULT-II Functions (IPDM E/R) ......................207
Parking, License Plate and Tail Lamps Do Not Illu-
minate ...................................................................208
Tail lamp Indicator Does Not Illuminate ................212
Parking, License Plate and Tail Lamps Do Not Go
OFF ......................................................................213
Bulb Replacement ................................................215
LICENSE PLATE LAMP ....................................215
PARKING LAMP ................................................215
TAIL LAMP ........................................................215
Removal and Installation ......................................215
LICENSE PLATE LAMP ....................................215
PARKING LAMP ................................................215
TAIL LAMP ........................................................215
REAR COMBINATION LAMP .................................216
Bulb Replacement ................................................216
REAR TURN SIGNAL LAMP BULB, BACK-UP
LAMP BULB AND STOP/TAIL LAMP BULB ......216
Removal and Installation ......................................216
REMOVAL .........................................................216
INSTALLATION ..................................................216
INTERIOR LAMP ....................................................217Wiring Diagram — INT/L — ..................................217
Bulb Replacement .................................................218
VANITY MIRROR LAMP ....................................218
INTERIOR ROOM LAMP ........................................219
Component Parts and Harness Connector Location .219
System Description ...............................................219
OUTLINE ...........................................................219
SWITCH OPERATION .......................................220
STEP LAMP OPERATION .................................221
TRUNK ROOM LAMP OPERATION ..................221
INTERIOR ROOM LAMP TIMER OPERATION .221
INTERIOR ROOM LAMP BATTERY SAVER
CONTROL .........................................................222
Schematic .............................................................223
Wiring Diagram — ROOM/L — .............................225
Terminals and Reference Values for BCM ............230
How to Perform With Trouble Diagnoses ..............231
Preliminary Check .................................................232
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ...................................................................232
CONSULT-II Functions (BCM) ..............................233
CONSULT-II BASIC OPERATION .....................233
WORK SUPPORT (INT LAMP) .........................233
DATA MONITOR (INT LAMP) ............................233
ACTIVE TEST ....................................................234
WORK SUPPORT (BATTERY SAVER) .............234
DATA MONITOR (BATTERY SAVER) ...............235
Interior Room Lamps Do Not Illuminate ................236
Interior Room Lamps Illuminate But Timer Does Not
Operate .................................................................240
Bulb Replacement .................................................241
MAP LAMP ........................................................241
STEP LAMP .......................................................241
PERSONAL LAMP .............................................241
TRUNK ROOM LAMP ........................................241
IGNITION KEYHOLE ILLUMINATION ...............242
Removal and Installation .......................................242
MAP LAMP ........................................................242
STEP LAMP .......................................................242
PERSONAL LAMP .............................................243
TRUNK ROOM LAMP ........................................243
ILLUMINATION ........................................................244
System Description ...............................................244
OUTLINE ...........................................................244
ILLUMINATION OPERATION BY LIGHTING
SWITCH .............................................................244
EXTERIOR LAMP BATTERY SAVER CONTROL .246
CAN Communication System Description ............246
CAN Communication Unit .....................................246
Schematic .............................................................247
Wiring Diagram — ILL — ......................................249
Bulb Replacement .................................................260
ASHTRAY ILLUMINATION ................................260
GLOVE BOX LAMP ...........................................260
CIGARETTE LIGHTER ILLUMINATION ............260
BULB SPECIFICATIONS ........................................261
Headlamp ..............................................................261
Exterior Lamp ........................................................261
Interior Lamp/Illumination ......................................261

LT-218
INTERIOR LAMP

Bulb ReplacementBKS002EL
VANITY MIRROR LAMP
1. Insert a thin screwdriver in the lens and remove lens.
2. Remove bulb together with substrate.
Vanity mirror lamp : 12V - 1.8W
SKIB0902E

ILLUMINATION
LT-245
C
D
E
F
G
H
I
J
L
MA
B
LT


to VDC off switch (illumination) terminal 3 (with VDC)

to CD auto changer (illumination) terminal 14 (with CD auto changer)

to audio unit (illumination) terminal 8

to door mirror remote control switch (illumination) terminal 16

to hazard switch (illumination) terminal 3

to headlamp washer switch (illumination) terminal 3

to cigarette lighter socket terminal 2

to headlamp aiming switch (illumination) terminal 3 (without xenon headlamp)

to A/C and AV switch (illumination) terminal 16

to front heated seat switch (driver side) (illumination) terminal 5

to front heated seat switch (passenger side) (illumination) terminal 5

to front air massage seat switch (illumination) terminal 5 (with air massage seat)

to front door armrest illumination (driver side) terminal 1

to front door armrest illumination (passenger side) terminal 1

to rear door armrest illumination LH terminal 1

to rear door armrest illumination RH terminal 1

to rear sunshade rear switch (illumination) terminal 8 (with rear center armrest switches)

to rear audio control switch (illumination) terminal 17 (with rear center armrest switches)

to rear heated seat switch LH (illumination) terminal 25 (with rear heated seat) and

to rear heated seat switch RH (illumination) terminal 33 (with rear heated seat),

through BCM terminal 16

to display control unit (illumination) terminal 14 (with display control unit)

to display unit (illumination) terminal 4 (without display control unit).
Ground is supplied

to glove box lamp terminal 2

to A/T device illumination terminal 2 (with A/T)

to CVT device illumination terminal 2 (with CVT)

to rear sunshade front switch (illumination) terminal 6 (with rear sunshade)

to VDC off switch (illumination) terminal 4 (with VDC)

to door mirror remote control switch (illumination) terminal 15

to hazard switch (illumination) terminal 4

to headlamp washer switch (illumination) terminal 4

to cigarette lighter socket terminal 1

to headlamp aiming switch (illumination) terminal 4 (without xenon headlamp)

to A/C and AV switch (illumination) terminal 15

to display control unit (illumination) terminal 3 (with display control unit)

to display unit (illumination) terminal 6 (without display control unit)

to front heated seat switch (driver side) (illumination) terminal 6

to front heated seat switch (passenger side) (illumination) terminal 6

to front air massage seat switch (illumination) terminal 6 (with air massage seat)

to front door armrest illumination (driver side) terminal 2 and

to front door armrest illumination (passenger side) terminal 2

through grounds M71 and M72,

to CD auto changer (illumination) (with CD auto changer) and

to Audio unit (illumination)

through case ground,

to rear door armrest illumination LH terminal 2

to rear sunshade rear switch (illumination) terminal 9 (with rear center armrest switches)

to rear audio control switch (illumination) terminal 18 (with rear center armrest switches)