Oil NISSAN TEANA 2003 Service Manual

EM-158
[VQ]
FUEL INJECTOR AND FUEL TUBE

CAUTION:

Upper and lower O-rings are different. Be careful not to confuse them.

Handle O-ring with bare hands. Do not wear gloves.

Lubricate O-ring with new engine oil.

Do not clean O-ring with solvent.

Make sure that O-ring and its mating part are free of foreign material.

When installing O-ring, be careful not to scratch it with tool or fingernails. Also be careful not to
twist or stretch O-ring. If O-ring was stretched while it was being attached, do not insert it
quickly into fuel tube.

Insert O-ring straight into fuel injector. Do not decenter or twist it.
3. Install fuel injector to fuel tube as follows:
a. Insert clip into clip mounting groove on fuel injector.

Insert clip so that protrusion “A” of fuel injector matches cut-
out“A” of clip.
CAUTION:

Do not reuse clip. Replace it with new one.

Be careful to keep clip from interfering with O-ring. If
interference occurs, replace O-ring.
b. Insert fuel injector into fuel tube with clip attached.

Insert it while matching it to the axial center.

Insert fuel injector so that protrusion “B” of fuel tube matches
cutout “B” of clip.

Make sure that fuel tube flange is securely fixed in flange fix-
ing groove on clip.
c. Make sure that installation is complete by checking that fuel
injector does not rotate or come off.

Make sure that protrusions of fuel injectors are aligned with
cutouts of clips after installation.
4. Install spacers on intake manifold.
5. Install fuel tube and fuel injector assembly to intake manifold
CAUTION:
Be careful not to let tip of injector nozzle come in contact with other parts.

Tighten mounting bolts in two steps in numerical order as
shown in the figure.Fuel tube side
VQ23DE : Black
VQ35DE : Blue
Nozzle side
VQ23DE : Green
VQ35DE : Brown
PBIC2545E
1st step
: 10.1 N·m (1.0 kg-m, 7 ft-lb)
2nd step
: 23.6 N·m (2.4 kg-m, 17 ft-lb)
SEC999C

FUEL INJECTOR AND FUEL TUBE
EM-159
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

6. Connect fuel injector harness connector.
7. Install intake manifold collectors (upper and lower). Refer to EM-133, "
INTAKE MANIFOLD COLLECTOR"
.
8. Connect fuel feed hose (with damper).

Handling procedure of O-ring is the same as that of fuel damper.

Insert fuel damper straight into fuel tube.

Tighten mounting bolts evenly in turn.

After tightening mounting bolts, make sure that there is no gap between flange and fuel tube.
9. Connect quick connector between fuel feed hose (with damper) and centralized under-floor piping con-
nection as follows:
a. Make sure no foreign substances are deposited in and around centralized under-floor piping and quick
connector, and no damage on them.
b. Thinly apply new engine oil around centralized under-floor piping from tip end to spool end.
c. Align center to insert quick connector straightly into centralized under-floor piping.

Insert quick connector to centralized under-floor piping until
top spool is completely inside quick connector, and 2nd level
spool exposes right below quick connector.
CAUTION:

Hold “A” position as shown in the figure when inserting
centralized under-floor piping into quick connector.

Carefully align center to avoid inclined insertion to pre-
vent damage to O-ring inside quick connector.

Insert until you hear a “click” sound and actually feel the
engagement.

To avoid misidentification of engagement with a similar
sound, be sure to perform the next step.
d. Pull quick connector by hand holding “A” position. Make sure it is completely engaged (connected) so that
it does not come out from centralized under-floor piping.
e. Install quick connector cap to quick connector.

Install quick connector cap with arrow on surface facing in
direction of quick connector [fuel feed hose (with damper)
side].
CAUTION:
If quick connector cap cannot be installed smoothly, quick
connector may have not been installed correctly. Check
connection again.
10. Install in the reverse order of removal after this step.
INSPECTION AFTER INSTALLATION
Check Fuel Leakage
1. Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
NOTE:
Use mirrors for checking at points out of clear sight.
2. Start engine. With engine speed increased, check again for fuel leakage at connection points.
CAUTION:
Do not touch engine immediately after stopped, as engine becomes extremely hot.
PBIC2471E
PBIC2893E

EM-160
[VQ]
ROCKER COVER

ROCKER COVERPFP:13264
Removal and InstallationBBS004VY
REMOVAL
1. Remove engine cover. Refer to EM-133, "INTAKE MANIFOLD COLLECTOR" .
2. Remove intake manifold collectors (upper and lower). (At the right bank side remove) Refer to EM-133,
"INTAKE MANIFOLD COLLECTOR" .
3. Remove ignition coil. Refer to EM-152, "
IGNITION COIL" .
4. Remove PCV hoses from rocker covers.
5. Remove PCV valve and O-ring from rocker cover (right bank), if necessary.
6. Remove oil filler cap from rocker cover (left bank), if necessary.
1. PCV hose 2. Oil filler cap 3. Rocker cover (right bank)
4. PCV hose 5. PCV valve 6. O-ring
7. Rocker cover gasket (right bank) 8. PCV hose 9. Rocker cover gasket (left bank)
10. Rocker cover (left bank)
PBIC2473E

EM-162
[VQ]
ROCKER COVER

4. Tighten mounting bolts two steps separately in numerical order
as shown in the figure.
5. Install oil filer cap to rocker cover (left bank), if removed.
6. Install new O-ring and PCV valve to rocker cover (right bank), if removed.
7. Install PCV hoses.

Insert PCV hose by 25 to 30 mm (0.98 to 1.18 in) from connector end.

When installing, be careful not to twist or come in contact with other parts.
8. Install in the reverse order of removal after this step. 1st step
: 2.0 N·m (0.20 kg-m, 18 in-lb)
2nd step
: 8.3 N·m (0.85 kg-m, 73 in-lb)
PBIC1184E

FRONT TIMING CHAIN CASE
EM-163
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

FRONT TIMING CHAIN CASEPFP:13599
Removal and InstallationBBS004VZ
NOTE:

This section describes removal/installation procedure of front timing chain case and timing chain related
parts without removing oil pan (upper) on vehicle.

When oil pan (upper) needs to be removed or installed, or when rear timing chain case is removed or
installed, remove oil pans (lower and upper) first. Then remove front timing chain case, timing chain
related parts, and rear timing chain case in this order, and install in the reverse order of removal. Refer to
EM-173, "
TIMING CHAIN" .

Refer to EM-173, "TIMING CHAIN" for component parts location.
REMOVAL
1. Remove engine cover. Refer to EM-133, "INTAKE MANIFOLD COLLECTOR" .
2. Remove air duct (inlet), air cleaner case (upper) with mass air flow sensor and air duct assembly. Refer to
EM-131, "
AIR CLEANER AND AIR DUCT" .
3. Remove undercover and splash guard (RH).
4. Remove right side front road wheel and tire.
5. Drain engine oil. Refer to LU-21, "
Changing Engine Oil" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine oil on drive belts.
6. Drain engine coolant from radiator. Refer to CO-34, "
Changing Engine Coolant" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine coolant on drive belts.
7. Remove intake manifold collectors (upper and lower). Refer to EM-133, "
INTAKE MANIFOLD COLLEC-
TOR" .
8. Remove drive belts. Refer to EM-128, "
DRIVE BELTS" .
9. Remove alternator. Refer to SC-27, "
CHARGING SYSTEM" .
10. Remove power steering oil pump from bracket with piping connected, and temporarily secure it to aside.
Refer to PS-29, "
POWER STEERING OIL PUMP" .
11. Remove power steering oil pump bracket. Refer to PS-29, "
POWER STEERING OIL PUMP" .
12. Remove idler pulley and bracket. Refer to EM-173, "
TIMING CHAIN" .
13. Separate engine harnesses removing their brackets from front timing chain case.
14. Remove rocker covers (right and left bank). Refer to EM-160, "
ROCKER COVER" .
NOTE:
When only timing chain (primary) is removed, rocker cover does not need to be removed.
15. Obtain No. 1 cylinder at TDC of its compression stroke as follows:
NOTE:
When timing chain is not removed/installed, this step is not required.
a. Rotate crankshaft pulley clockwise to align timing mark (grooved
line without color) with timing indicator.
SEM918G

EM-164
[VQ]
FRONT TIMING CHAIN CASE

b. Make sure that intake and exhaust cam noses on No. 1 cylinder
(engine front side of right bank) are located as shown in the fig-
ure.

If not, turn crankshaft one revolution (360 degrees) and align
as shown in the figure.
NOTE:
When only timing chain (primary) is removed, rocker cover does
not need to be removed. To make sure that No. 1 cylinder is at
its compression TDC, remove front timing chain case first. Then
check mating marks on camshaft sprockets. Refer to EM-181,
"INSTALLATION" .
16. Remove crankshaft pulley as follows:
a. Fix crankshaft with pulley holder (SST).
b. Loosen crankshaft pulley bolt and locate bolt seating surface at
10 mm (0.39 in) from its original position.
CAUTION:
Do not remove crankshaft pulley bolt as it will be used as a
supporting point for suitable puller.
c. Place suitable puller tab on holes of crankshaft pulley, and pull
crankshaft pulley through.
CAUTION:
Do not put suitable puller tab on crankshaft pulley periph-
ery, as this will damage internal damper.
17. Remove oil pan (lower). Refer to EM-145, "
OIL PAN AND OIL STRAINER" .
18. Loosen two mounting bolts in front of oil pan (upper) in the
reverse order as shown in the figure.
19. Install oil pan (lower) temporarily.

Applying liquid gasket is unnecessary.
20. Support the oil pan (lower) bottom with jack.

Perform following operations with engine front side supported with jack.
CAUTION:
Put a piece of wood or something similar as the supporting surface, be careful not to damage oil
pan (lower).
21. Remove right and left intake valve timing control covers.
SEM418G
PBIC2475E
SEM915E
PBIC1637E

FRONT TIMING CHAIN CASE
EM-165
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM


Loosen mounting bolts in the reverse order as shown in the
figure.

U s e s e a l c u t t e r [ S S T: K V 1 0 1111 0 0 ] o r e q u i v a l e n t t o o l t o c u t
liquid gasket for removal.
CAUTION:
Shaft is internally jointed with camshaft sprocket (INT) cen-
ter hole. When removing, keep it horizontal until it is com-
pletely disconnected.
22. Remove collared O-rings from front timing chain case oil holes
(left and right sides).
23. Remove engine mounting insulator (RH) and engine mounting bracket (RH). Refer to EM-223, "
ENGINE
ASSEMBLY" .
24. Raise engine front side with jack. (This secures workspace to remove front timing chain case.)
25. Remove front timing chain case as follows:
a. Loosen mounting bolts in the reverse order as shown in the fig-
ure.
b. Insert suitable tool into the notch at the top of front timing chain
case as shown (1).
c. Pry off case by moving tool as shown (2).

U s e s e a l c u t t e r [ S S T: K V 1 0 1111 0 0 ] t o c u t l i q u i d g a s k e t f o r
removal.
CAUTION:

Do not use screwdriver or something similar.

After removal, handle front timing chain case carefully so
it does not tilt, cant, or warp under a load.
PBIC0918E
PBIC2631E
SEM730G
SEM156F

EM-166
[VQ]
FRONT TIMING CHAIN CASE

26. Remove O-rings from rear timing chain case.
27. Remove water pump cover and chain tensioner cover from front timing chain case.

Use seal cutter [SST: KV10111100] to cut liquid gasket for removal.
28. Remove front oil seal from front timing chain case using suitable
tool.

Use screwdriver for removal.
CAUTION:
Be careful not to damage front timing chain case.
29. Remove timing chain and related parts. Refer to EM-173, "
TIMING CHAIN" .
30. Use scraper to remove all traces of old liquid gasket from front
and rear timing chain cases and oil pan (upper), and liquid gas-
ket mating surfaces.
CAUTION:
Be careful not to allow gasket fragments to enter oil pan.

Remove old liquid gasket from bolt hole and thread.
INSTALLATION
1. Install timing chain and related parts. Refer to EM-173, "TIMING CHAIN" .
PBIC2548E
EMQ0032D
SEM737G
PBIC2084E

FRONT TIMING CHAIN CASE
EM-167
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

2. Hammer dowel pins (right and left) into front timing chain case
up to a point close to taper in order to shorten protrusion length.
3. Install new front oil seal on front timing chain case.

Apply new engine oil to both oil seal lip and dust seal lip.

Install it so that each seal lip is oriented as shown in the fig-
ure.

Using suitable drift [outer diameter: 60 mm (2.36 in)], press-fit
oil seal until it becomes flush with front timing chain case end
face.

Make sure the garter spring is in position and seal lip is not
inverted.
4. Install water pump cover and chain tensioner cover to front timing chain case.

Apply a continuous bead of liquid gasket with tube presser
[SST: WS39930000] to front timing chain case as shown in
the figure.
Use Genuine Liquid Gasket or equivalent.
5. Install front timing chain case as follows:
PBIC2615E
SEM715A
PBIC0790E
SEM744GA

EM-168
[VQ]
FRONT TIMING CHAIN CASE

a. Apply a continuous bead of liquid gasket with tube presser [SST:
WS39930000] to front timing chain case back side as shown in
the figure.
Use Genuine Liquid Gasket or equivalent.
b. Install new oil pan gasket.

Apply liquid gasket to oil pan gasket as shown in the figure.
Use Genuine Liquid Gasket or equivalent.

Align notch of front timing chain case with protrusion of oil pan
gasket.
PBIC2648E
PBIC2630E
PBIC1114E