bulb NISSAN TEANA 2003 Owner's Guide

LT-62
HEADLAMP - HALOGEN TYPE -

Bulb ReplacementBKS001O2
HEADLAMP (UPPER) HIGH BEAM
1. Turn lighting switch OFF.
2. Remove washer tank inlet when replacing bulb RH. Refer to WW-38, "
Removal and Installation of Washer
Ta n k" .
Remove air cleaner case when replacing bulb LH. Refer to EM-17, "
Removal and Installation" (models
with QR engine), or EM-131, "
Removal and Installation" (models with VQ engine).
3. Turn plastic cap counterclockwise and unlock it.
4. Remove the socket connected to the bulb.
5. Unlock retaining spring and remove bulb from headlamp.
HEADLAMP (LOWER) LOW BEAM
1. Turn lighting switch OFF.
2. Remove washer tank inlet when replacing bulb RH. Refer to WW-38, "
Removal and Installation of Washer
Ta n k" .
Remove air cleaner case when replacing bulb LH. Refer to EM-17, "
Removal and Installation" (models
with QR engine), or EM-131, "
Removal and Installation" (models with VQ engine).
3. Turn plastic cap counterclockwise and unlock it.
4. Remove the socket connected to the bulb.
5. Unlock retaining spring and remove bulb from headlamp.
PARKING LAMP
1. Turn lighting switch OFF.
2. Remove fender protector (front). Refer to EI-23, "
Removal and Installation" .
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb from its socket.
FRONT TURN SIGNAL LAMP
1. Turn lighting switch OFF.
2. Remove fender protector (front). Refer to EI-23, "
Removal and Installation" .
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb from its socket.
CAUTION:
After installing bulb, be sure to install plastic cap and bulb socket securely to ensure watertight-
ness.
Removal and InstallationBKS001O3
Refer to LT- 3 6 , "Removal and Installation" .
NOTE:
After installation, perform aiming adjustment. Refer to LT- 6 0 , "
Aiming Adjustment" . Headlamp (upper) high beam : 12V - 55W (H7)
Headlamp (lower) low beam : 12V - 55W (H11)
Parking lamp : 12V - 5W
Front turn signal lamp : 12V - 21W (amber)

HEADLAMP - HALOGEN TYPE -
LT-63
C
D
E
F
G
H
I
J
L
MA
B
LT

Disassembly and AssemblyBKS001O4
DISASSEMBLY
1. Turn plastic cap counterclockwise and unlock it.
2. Disconnect bulb socket (low).
3. Unlock retaining spring and remove bulb (low).
4. Disconnect bulb socket (high).
5. Unlock retaining spring and remove bulb (high).
6. Turn parking lamp bulb socket counterclockwise and unlock it.
7. Remove parking lamp bulb from its socket.
8. Turn front turn signal lamp bulb socket counterclockwise and unlock it.
9. Remove front turn signal lamp bulb from its socket.
ASSEMBLY
Note the following, and assembly is the reverse order of disassembly.
CAUTION:

After installing bulb, be sure to install plastic cap and bulb socket securely to insure watertight-
ness.
1. Retaining spring 2. Parking lamp bulb 3. Parking lamp bulb socket
4. Bulb (high) 5. Seal packing 6. Bulb socket (high)
7. Plastic cap 8. Front turn signal lamp bulb 9. Front turn signal lamp bulb socket
10. Plastic cap 11. Seal packing 12. Bulb socket (low)
13. Bulb (low) 14. Headlamp housing assembly
PKIC9269J

ACTIVE AFS
LT-91
C
D
E
F
G
H
I
J
L
MA
B
LT

4. CHECK BENDING LAMP GROUND
Check continuity between bending lamp (RH and LH) harness con-
nector and ground.
OK or NG
OK >> Replace bending lamp bulbs.
NG >> Repair harness or connector.
Bending Lamp Does Not Illuminate (One Side)BKS002FC
1. CHECK BULB
Check bulb of bending lamp which does not illuminate.
OK or NG
OK >> GO TO 2.
NG >> Replace bending lamp bulb.
2. CHECK CIRCUIT BETWEEN AFS CONTROL UNIT AND BENDING LAMP
1. Turn ignition switch OFF.
2. Disconnect AFS control unit connector and bending lamp RH or LH connector.
3. Check harness continuity between AFS control unit harness
connector (A) and bending lamp RH or LH harness connector
(B).
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.
3. CHECK BENDING LAMP GROUND
Check continuity between bending lamp RH or LH harness connec-
tor and ground.
OK or NG
OK >> Replace AFS control unit. Refer to LT- 9 4 , "Removal and
Installation of AFS Control Unit" .
NG >> Repair harness or connector.
AFS control unit connector Terminal
GroundContinuity
RH E50 10
Ye s
LH E51 10
PKIC9896E
CircuitAB
Continuity
Connector Terminal Connector Terminal
RH
M938E509
Ye s
LH 3 E51 9
PKIC9897E
AFS control unit connector Terminal
GroundContinuity
RH E50 10
Ye s
LH E51 10
PKIC9896E

LT-94
ACTIVE AFS

Aiming AdjustmentBKS002FH
Refer to LT- 3 3 , "Aiming Adjustment" .
Bulb ReplacementBKS002FI
Refer to LT- 3 5 , "BENDING LAMP" .
Removal and Installation of AFS Control UnitBKS002FJ
REMOVAL
1. Remove instrument driver lower cover. Refer to IP-11, "Removal and Installation" .
2. Disconnect AFS control unit connector.
3. Remove screw (A).
4. Remove AFS control unit.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
Steering angle sensor adjustment whenever replacing AFS control unit. Refer to LT- 8 2 , "
WORK SUPPORT" .
Removal and Installation of Steering Angle SensorBKS002FK
REMOVAL
1. Remove combination switch (1). Refer to SRS-37, "Removal
and Installation" .
2. Remove screw (A).
3. Remove steering angle sensor (2).
INSTALLATION
Installation is the reverse order of removal.
NOTE:
Steering angle sensor adjustment whenever replacing steering angle sensor. Refer to LT- 8 2 , "
WORK SUP-
PORT" .
PKIC9222J
SKIB7829J

FRONT FOG LAMP
LT-137
C
D
E
F
G
H
I
J
L
MA
B
LT

6. CHECK CIRCUIT BETWEEN FRONT FOG LAMP AND GROUND
1. Turn ignition switch OFF.
2. Check continuity between front fog lamp (RH and LH) harness
connectors and ground.
OK or NG
OK >> Check front fog lamp bulb.
NG >> Repair harness or connector.
Front Fog Lamp Does Not Illuminate (One Side)BKS001P2
1. CHECK BULB
Check front fog lamp bulb which does not illuminate.
OK or NG
OK >> GO TO 2.
NG >> Replace front fog lamp bulb.
2. CHECK CIRCUIT BETWEEN IPDM E/R AND FRONT FOG LAMP
1. Disconnect IPDM E/R connector and front fog lamp RH or LH connector.
2. Check continuity between IPDM E/R harness connector (A) and
front fog lamp RH or LH harness connector (B).
3. Check continuity between IPDM E/R harness connector (A) and
ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK CIRCUIT BETWEEN FRONT FOG LAMP AND GROUND
Check continuity between front fog lamp RH or LH harness connec-
tor and ground.
OK or NG
OK >> Replace IPDM E/R. Refer to PG-28, "Removal and
Installation of IPDM E/R" .
NG >> Repair harness or connector.
Front fog lamp connector Terminal
GroundContinuity
RH E256 2
Ye s
LH E32 2
PKIA6277E
CircuitAB
Continuity
Connector Terminal Connector Terminal
RH
E836 E256 1
Ye s
LH 37 E32 1
A
GroundContinuity
Connector Terminal
RH
E836
No
LH 37
PKID0087E
Front fog lamp connector Terminal
Ground Continuity
RH E256 2
Ye s
LH E32 2
PKIA6277E

LT-140
FRONT FOG LAMP

Aiming AdjustmentBKS001P5
The front fog lamp is a semi-sealed beam type which uses a replaceable halogen bulb. Before performing
aiming adjustment, make sure of the following.

Keep all tires inflated to correct pressure.

Place vehicle on level ground.

See that vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and
tools). Have the driver or equivalent weight placed in driver seat.
Adjust aiming in the vertical direction by turning the adjustment screw.
1. Set the distance between the screen and the center of the front
fog lamp lens as shown in the figure.
2. Turn front fog lamps ON.
3. Adjust front fog lamps using adjusting screw so that the main
optical axis of the high intensity zone is in the figure.

When performing this adjustment, cover the headlamps and
the opposite front fog lamp, if necessary.
PKIC9407E
SKIB8679E
SKIB8680E

FRONT FOG LAMP
LT-141
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementBKS001P6
1. Turn lighting switch OFF.
2. Turn off the fender protector (front) to obtain work space between the fender protector and fender.
3. Disconnect front fog lamp connector.
4. Turn front for lamp bulb counterclockwise and unlock it.
CAUTION:

Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off. Burning may result.

Never leave bulb out of front fog lamp reflector for a long time because dust, moisture smoke, etc.
May affect the performance of front fog lamp. When replacing bulb, be sure to replace it with new
one.
Removal and InstallationBKS001P7
REMOVAL
1. Turn over the fender protector (front) and undercover to obtain work space between the fender protector
and fender.
2. Disconnect front fog lamp connector.
3. Remove nuts (3), pawl (2) and front fog lamp (1) from front bumper.
INSTALLATION
Installation is the reverse order of removal.Front fog lamp : 12V - 35W (H8)
PKIC9218J
1. Front fog lamp 2. Pawl 3. Front fog lamp mounting nut
:N·m (kg-m, in-lb)
PKIC9219J
Front fog lamp mounting nuts : 5.1 N·m (0.52 kg-m, 45 in-lb)

LT-150
REAR FOG LAMP

5. CHECK CIRCUIT BETWEEN REAR FOG LAMP AND GROUND
1. Turn ignition switch OFF.
2. Check continuity between rear fog lamp harness connector and
ground.
OK or NG
OK >> Check rear fog lamp bulb.
NG >> Repair harness or connector.
Rear Fog Lamp Indicator Lamp Does Not IlluminateBKS001PI
1. CHECK UNIFIED METER AND A/C AMP.
1. Select “METER A/C AMP” on CONSULT-II, and perform self-
diagnosis for “METER A/C AMP”.
2. Check if malfunction is indicated.
Is malfunction indicated?
YES >> Repair or Replace malfunctioning parts.
NO >> GO TO 2.
2. CHECK COMBINATION METER INPUT SIGNAL
1. Select “METER A/C AMP” on CONSULT-II.
2. Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “RR FOG IND” turns ON-OFF according to light-
ing switch operation.
OK or NG
OK >> Replace combination meter. DI-25, "Disassembly and
Assembly of Combination Meter" .
NG >> Replace unified meter and A/C amp. Refer to DI-34,
"Removal and Installation of Unified Meter and A/C
Amp." .
Rear fog lamp connector Terminal
GroundContinuity
B30 2 Yes
PKID0092E
PKIA6866E
When lighting switch is in the
rear fog lamp ON position: RR FOG IND ON
PKID0093E

REAR FOG LAMP
LT-151
C
D
E
F
G
H
I
J
L
MA
B
LT

Rear Fog Lamp Does Not Go OFFBKS001PJ
1. PERFORM BCM ACTIVE TEST
1. Select “BCM” on CONSULT-II, and select “HEAD LAMP” on “SELECT TEST ITEM” screen.
2. Select “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3. Touch “RR FOG LAMP” screen.
Does rear fog lamp turn OFF?
YES >> GO TO 2.
NO >> Replace BCM. Refer to BCS-16, "
Removal and Installa-
tion of BCM" .
2. CHECK CIRCUIT BETWEEN COMBINATION SWITCH AND BCM
With CONSULT-II
1. Select “BCM” on CONSULT-II, and select “HEADLAMP” on “SELECT TEST ITEM” screen.
2. Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “RR FOG SW” turns ON-OFF according to light-
ing switch operation.
Without CONSULT-II
Refer to LT- 1 8 5 , "
Combination Switch Inspection" .
OK or NG
OK >> Replace BCM. Refer to BCS-16, "Removal and Installa-
tion of BCM" .
NG >> Check combination switch (lighting switch). Refer to LT- 1 8 5 , "
Combination Switch Inspection" .
Bulb ReplacementBKS001PK
Refer to LT- 2 1 6 , "Bulb Replacement" .
Removal and InstallationBKS001PL
Refer to LT- 2 1 6 , "Removal and Installation" .
PKIB7213E
When lighting switch is in the
rear fog lamp OFF position: RR FOG SW OFF
PKID0280E

LT-166
TURN SIGNAL AND HAZARD WARNING LAMPS

5. CHECK CIRCUIT BETWEEN TURN SIGNAL LAMP AND GROUND
1. Turn ignition switch OFF.
2. Check continuity between front combination lamp RH harness connector and ground.
3. Check continuity between side turn signal lamp RH harness
connector and ground.
4. Check continuity between rear combination lamp RH harness
connector and ground.
OK or NG
OK >> Check turn signal lamps RH bulbs.
NG >> Repair harness or connector.
Headlamp typeFront combination
lamp RH connectorTerminal
GroundContinuity
Xenon E15
4Yes
Conventional E47
SKIB8819E
Side turn signal
lamp RH connectorTerminal
GroundContinuity
E251 2 Yes
PKID0098E
Rear combination
lamp RH connectorTerminal
GroundContinuity
B25 2 Yes
PKID0099E