Oil NISSAN TEANA 2003 Service Manual

PREPARATION
FSU-3
C
D
F
G
H
I
J
K
L
MA
B
FSU

PREPARATIONPFP:00002
Special Service Tools BES0003H
Commercial Service ToolsBES0003I
Tool number
Tool nameDescription
KV991040S0
CCK gauge attachment
1. Plate
2. Guide bolts
3. Nuts
4. Springs
5. Center plate
6. KV99104020 Adapter A
a: 72 mm (2.83 in) dia.
7. KV99104030 Adapter B
b: 65 mm (2.56 in) dia.
8. KV99104040 Adapter C
c: 57 mm (2.24 in) dia.
9. KV99104050 Adapter D
d: 53.4 mm (2.102 in) dia.Measuring wheel alignment
ST35652000
Strut attachmentDisassembling and assembling strut
ST3127S000
Preload gauge
1. GG9103000
Torque wrench
2. HT6294000
Socket adapter (1/2″)
3. HT6290000
Socket adapter (3/8″)Measuring rotating torque of ball joint
S-NT498
ZZA0807D
NT124
Tool nameDescription
Spring compressor Removing and installing coil spring
S-NT717

FRONT SUSPENSION ASSEMBLY
FSU-5
C
D
F
G
H
I
J
K
L
MA
B
FSU

FRONT SUSPENSION ASSEMBLYPFP:54010
On-Vehicle Inspection BES0003K
Make sure that the mounting conditions (looseness, back lash) of each component and component status
(wear, damage) are normal.
INSPECTION OF TRANSVERSE LINK BALL JOINT END PLAY
1. Set front wheels in a straight-ahead position. Do not depress brake pedal.
2. Measure axial end play by placing an iron pry bar or a similar item between suspension arm and strut
assembly and prying up and down.
CAUTION:
Be careful not to damage ball joint boot. Do not damage the installation position by applying
excessive force.
STRUT INSPECTION
Check for oil leakage, damage, and breakage of installation positions.
Wheel Alignment InspectionBES0003L
DESCRIPTION
Measure wheel alignment under unladen conditions.
NOTE:
“Unladen” conditions mean that fuel, engine coolant, and lubricant are full. A spare tire, a jack, hand tools and
mats are in designated positions.
PRELIMINARY CHECK
1. Check Tires for improper air pressure and wear.
2. Check Road wheels for runout. Refer to WT-3, "
ROAD WHEEL" .
3. Check Wheel bearing axial end play. Refer to FAX-5, "
WHEEL BEARING INSPECTION" .
4. Check Transverse link ball joint axial end play. Refer to FSU-14, "
INSPECTION AFTER REMOVAL" .
5. Check Strut operation.
6. Check Each mounting point of axle and suspension for looseness and deformation.
7. Check Each link, rod, and member for cracks, deformation and other damage.
8. Check Vehicle height (posture).
INSPECTION OF CAMBER, CASTER AND KINGPIN INCLINATION ANGLES.

Camber, caster, kingpin inclination angles cannot be adjusted.

Before inspection, mount wheels onto turning radius gauge. Mount rear wheels onto a stand that has
same height so vehicle will remain horizontal.
Using a CCK Gauge
Install CCK gauge attachment [SST:KV991040S0] with the following procedure on wheel, then measure wheel
alignment.
1. Remove three wheel nuts, and install the guide bolts to hub
bolts.
2. Screw adapter into the plate until it contacts the plate tightly.
3. Screw center plate into the plate.
4. Insert plate on guide bolt. Put spring in, and then evenly screw
both guide bolt nuts. When fastening guide bolt nuts, do not
completely compress the spring.Axial end play : 0 mm (0 in)
SEIA0240E

FSU-8
FRONT SUSPENSION ASSEMBLY

Removal and Installation BES0003N
REMOVAL
1. Remove cowl top panel and hood. Install engine slinger, and then hoist engine. (VQ35DE models) Refer
to EI-21, "
COWL TOP" , BL-13, "HOOD" .
2. Remove tires from vehicle.
3. Remove wheel sensor from steering knuckle. Refer to BRC-33, "
WHEEL SENSORS" .
CAUTION:
Do not pull on wheel sensor harness.
4. Remove torque member fixing bolts. Hang torque member in a place where it will not interfere with work.
Refer to BR-26, "
FRONT DISC BRAKE" .
NOTE:
Do not depress brake pedal while brake caliper is removed.
5. Remove undercover and splash guard.
6. Remove disc rotor. Refer to FA X - 5 , "
Removal and Installation" .
7. Remove the mounting nut on the upper side of stabilizer con-
necting rod, and then remove stabilizer connecting rod from strut
assembly. Refer to FSU-16, "
STABILIZER BAR" .
8. Remove fixing nuts and bolts with, and then remove steering
knuckle from strut assembly. Refer to FSU-10, "
Removal and
Installation" .
9. Remove cotter pin, then loosen hub lock nut.
10. Separate wheel hub and bearing assembly from drive shaft by
lightly tapping the end with a hammer (suitable tool) and a wood
block, and then remove lock nut.
CAUTION:

Do not place drive shaft joint at an extreme angle. Also be
careful not to overextend slide joint.

Do not allow drive shaft to hang down without support for
housing (or joint sub-assembly), shaft and the other parts.
NOTE:
Use a puller (suitable tool) if wheel hub and drive shaft cannot be separated even after performing the
above procedure.
11. Remove front exhaust tube. Refer to EX-2, "
EXHAUST SYSTEM" .
12. Remove heat insulator.(Except for QR20DE models)
1. Upper mounting plate 2. Mounting insulator 3. Mounting insulator bracket
4. Mounting bearing 5. Spring upper seat 6. Spring upper rubber seat
7. Coil spring 8. Lower spring seat 9. Bound bumper
10. Strut 11. Stabilizer clamp 12. Stabilizer bushing
13. Stabilizer bar 14. Stabilizer connecting rod 15. Strut assembly
16. Front axle assembly 17. Member stay 18. Transverse link
19. Front suspension member 20. Rebound stopper 21. Heat insulator (Except for QR20DE
models)
22. Damper assembly (For VQ35DE
models)
Refer to GI-10, "
Components" , for the symbols in the figure.
SEIA0370E
SEIA0411J

FSU-10
COIL SPRING AND STRUT

COIL SPRING AND STRUTPFP:55302
Removal and InstallationBES0003O
REMOVAL
1. Remove tires from vehicle.
2. Remove harness of wheel sensor from strut assembly. Refer to
BRC-33, "
WHEEL SENSORS" .
CAUTION:
Do not pull on wheel sensor harness.
3. Remove torque member fixing bolts. Hang torque member in a
place where it will not interfere with work. Refer to BR-26,
"FRONT DISC BRAKE" .
NOTE:
Do not depress brake pedal while brake caliper is removed.
4. Remove lock plate and brake hose from strut assembly. Refer to
BR-12, "
Removal and Installation of Front Brake Tube and
Hose" .
5. Remove disc rotor. Refer to FA X - 5 , "
Removal and Installation" .
6. Remove mounting nut of the upper side of stabilizer connecting
rod, and then remove stabilizer connecting rod from strut
assembly. Refer to FSU-16, "
STABILIZER BAR" .
7. Remove fixing nuts and bolts, and then remove steering knuckle
from strut assembly.
8. Remove mounting nuts of mounting insulator bracket, then
remove strut assembly from vehicle.
SEIA0369E
SGIA1758E
SEIA0370E
SEIA0411J

COIL SPRING AND STRUT
FSU-11
C
D
F
G
H
I
J
K
L
MA
B
FSU

INSTALLATION

Installation is the reverse order of the removal. For tightening torque, refer to FSU-7, "Components" .
NOTE:
Do not reuse non-reusable parts.

Perform final tightening of each of parts under unladen conditions, which were removed when removing
coil spring and strut. Check the wheel alignment. Refer to FSU-5, "
Wheel Alignment Inspection" .

Adjust neutral position of steering angle sensor after checking the wheel alignment for models with VDC.
Refer to BRC-40, "
Adjustment of Steering Angle Sensor Neutral Position" .

Check wheel sensor harness for proper connection. Refer to BRC-33, "WHEEL SENSORS" .

Be sure that the identification letters on mounting insulator face
in the direction shown in the figure, and then install strut assem-
bly to the vehicle.
Disassembly and AssemblyBES0003P
DISASSEMBLY
CAUTION:
Do not damage strut piston rod when removing components from strut.
1. Install strut attachment [SST] to strut and secure it in a vise.
CAUTION:
Wrap a shop cloth around strut to protect it from damage
when installing strut attachment [SST] to strut.
2. Compress coil spring between upper rubber seat and lower rub-
ber seat (strut) using spring compressor (commercial service
tool) until coil spring is free.
CAUTION:
Start compressing coil spring after making sure that the
compressor is completely attached to coil spring.
3. Make sure that coil spring with the compressor is free between
spring upper rubber seat and lower spring seat (strut), and then
remove piston rod lock nut while securing the end of piston rod
so as not to rotate piston rod.
4. Remove mounting insulator bracket, mounting bearing, spring
upper seat, spring upper rubber seat, bound bumper from strut.
5. Remove coil spring with the compressor, and then gradually release the compressor.
CAUTION:
Loosen the compressor while checking installation position so that compressor is installed to the
correct position.
6. Remove lower spring seat from strut.
7. Remove strut attachment [SST] from strut.
SEIA0371E
SEIA0372J
SEIA0297E

FSU-12
COIL SPRING AND STRUT

INSPECTION AFTER DISASSEMBLY
Strut Inspection

Check strut for deformation, cracks, and damage. Replace if there are.

Check piston rod for damage, uneven wear, and distortion. Replace if there are.

Check for oil leakage. Replace if there are.
Mounting Insulator and Rubber Parts Inspection
Check mounting insulator for cracks and rubber parts for wear. Replace if there are.
Coil Spring Inspection
Check coil spring for cracks, wear, and damage. Replace if there are.
ASSEMBLY
CAUTION:
Do not damage strut piston rod when installing components to strut.
1. Install the strut attachment [SST] to strut and secure it in a vise.
CAUTION:
Wrap a shop cloth around strut to protect it from damage
when installing strut attachment [SST] to strut.
2. Install lower spring seat to strut.
3. Compress coil spring using a spring compressor (commercial
service tool), and install it onto strut.
CAUTION:

Face the large diameter side of coil spring downward.
Align lower end to lower spring seat as shown in the fig-
ure.

Start compressing coil spring after making sure that
spring compressor (commercial service tool) is com-
pletely attached to coil spring.
4. Apply soapy water to bound bumper. Insert bound bumper into
spring upper seat, and then install it to strut together with spring
upper rubber seat.
SEIA0372J
SEIA0297E
SFA149

COIL SPRING AND STRUT
FSU-13
C
D
F
G
H
I
J
K
L
MA
B
FSU


Install spring upper seat with cutout facing outside vehicle as
shown in the figure.
5. Install strut mounting insulator bracket and mounting bearing to
strut.
6. Secure end of piston rod so as not to rotate piston rod, and then
tighten piston rod lock nut to the specified torque.
7. Gradually release spring compressor (commercial service tool),
and remove it from coil spring.
CAUTION:
Loosen a spring compressor while checking installation
position so that coil spring compressor is installed to the
correct position.
8. Remove strut attachment [SST] from strut.
SEIA0575E

FSU-18
SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Wheel Alignment (Unladen*)BES0003T
*: Fuel, engine coolant and engine oil full. Spare tire, jack, hand tools and mats are in designated positions.
Ball JointBES0003U
Wheelarch Height (Unladen*)BES0003V
*: Fuel, engine coolant and engine oil full. Spare tire, jack, hand tools and mats are in designated positions.Camber
Degree minute (Decimal degree)Minimum –1° 00′ (–1.00°)
Nominal –0° 15′ (–0.25°)
Maximum 0° 30′ (0.50°)
Left and right difference 45′ (0.75°) or less
Caster
Degree minute (Decimal degree)Minimum 2° 05′ (2.08°)
Nominal 2° 50′ (2.83°)
Maximum 3° 35′ (3.58°)
Left and right difference 45′ (0.75°) or less
Kingpin inclination
Degree minute (Decimal degree)Minimum 13° 50′ (13.83°)
Nominal 14° 35′ (14.58°)
Maximum 15° 20′ (15.33°)
Total toe-inDistanceMinimum –0.3 mm (–0.01 in)
Nominal 0.7 mm (0.03 in)
Maximum 1.7 mm (0.07 in)
Angle (left plus right)
Degree minute (Degree)Minimum 0′ (0°)
Nominal 2′ (0.03°)
Maximum 4′ (0.07°)
Swing torque 0.5 - 3.4 N·m (0.06 - 0.34 kg-m, 5 - 30 in-lb)
Measurement on spring balance 13.5 - 91.9 N (1.4 - 9.3 kg, 3.08 - 20.5 lb)
Rotating torque 0.5 - 3.4 N·m (0.06 - 0.34 kg-m, 5 - 30 in-lb)
Axial end play0 mm (0 in)
Tire size 205/65R16 215/55R17
Front (Hf)721 mm
(28.39 in)718 mm
(28.27 in)
Rear (Hr)702 mm
(27.64 in)698 mm
(27.48 in)
SFA818A

GI-1
GENERAL INFORMATION
A GENERAL INFORMATION
CONTENTS
C
D
E
F
G
H
I
J
K
L
MB
GI
SECTION GI

GENERAL INFORMATION
PRECAUTIONS .......................................................... 3
Description ............................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for NATS (NISSAN ANTI-THEFT SYS-
TEM) ........................................................................ 3
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 4
OPERATION PROCEDURE ................................. 4
General Precautions ................................................ 4
Precautions for Three Way Catalyst ......................... 6
Precautions for Fuel ................................................. 6
QR20DE/VQ23DE ENGINE (REGULAR GASO-
LINE, UNLEADED PREMIUM GASOLINE REC-
OMMENDED) ........................................................ 6
VQ35DE ENGINE (PREMIUM GASOLINE) ......... 6
Precautions for Multiport Fuel Injection System or
Engine Control System ............................................ 6
Precautions for Hoses .............................................. 7
HOSE REMOVAL AND INSTALLATION ............... 7
HOSE CLAMPING ................................................ 7
Precautions for Engine Oils ...................................... 8
HEALTH PROTECTION PRECAUTIONS ............. 8
Precautions for Air Conditioning ............................... 8
HOW TO USE THIS MANUAL ................................... 9
Description ............................................................... 9
Terms ....................................................................... 9
Units ......................................................................... 9
Contents ................................................................... 9
Components ........................................................... 10
SYMBOLS ........................................................... 10
How to Follow Trouble Diagnoses ........................... 11
DESCRIPTION ..................................................... 11
HOW TO FOLLOW TEST GROUPS IN TROU-
BLE DIAGNOSES ................................................ 11
HARNESS WIRE COLOR AND CONNECTOR
NUMBER INDICATION ....................................... 12
KEY TO SYMBOLS SIGNIFYING MEASURE-
MENTS OR PROCEDURES ............................... 13How to Read Wiring Diagrams ............................... 15
HEALTH PROTECTION PRECAUTIONS ............. 8
SYMBOLS ........................................................... 10
DESCRIPTION .................................................... 17
Abbreviations .......................................................... 23
SERVICE INFORMATION FOR ELECTRICAL INCI-
DENT ......................................................................... 24
How to Perform Efficient Diagnosis for an Electrical
Incident ................................................................... 24
WORK FLOW ...................................................... 24
INCIDENT SIMULATION TESTS ........................ 24
CIRCUIT INSPECTION ....................................... 27
Control Units and Electrical Parts ........................... 31
PRECAUTIONS .................................................. 31
CONSULT-II CHECKING SYSTEM .......................... 33
Description .............................................................. 33
Function and System Application ........................... 33
Nickel Metal Hydride Battery Replacement ............ 33
Checking Equipment .............................................. 34
CONSULT-II Start Procedure .................................. 34
CONSULT-II Data Link Connector (DLC) Circuit .... 35
INSPECTION PROCEDURE .............................. 35
CIRCUIT DIAGRAM ............................................... 36
LIFTING POINT ......................................................... 37
Commercial Service Tools ...................................... 37
Garage Jack and Safety Stand and 2-Pole Lift ....... 37
Board-On Lift .......................................................... 38
TOW TRUCK TOWING ............................................. 39
Tow Truck Towing ................................................... 39
TOWING AN AUTOMATIC TRANSAXLE
MODEL WITH THE FRONT WHEELS ON THE
GROUND ............................................................ 39
Vehicle Recovery (Freeing a Stuck Vehicle) ........... 39
TIGHTENING TORQUE OF STANDARD BOLTS .... 40
Tightening Torque Table ......................................... 40
IDENTIFICATION INFORMATION ............................ 41
Model Variation ....................................................... 41
IDENTIFICATION NUMBER ................................ 41
IDENTIFICATION PLATE .................................... 42
ENGINE SERIAL NUMBER ................................ 42

PRECAUTIONS
GI-5
C
D
E
F
G
H
I
J
K
L
MB
GI


Before starting repairs which do not require battery power:
Turn off ignition switch.
Disconnect the negative battery terminal.

If the battery terminals are disconnected, recorded memory of
radio and each control unit is erased.

Battery posts, terminals and related accessories contain lead
and lead compounds. Wash hands after handling.

To prevent serious burns:
Avoid contact with hot metal parts.
Do not remove the radiator cap when the engine is hot.

Dispose of or recycle drained oil or the solvent used for cleaning
parts in an appropriate manner.

Do not attempt to top off the fuel tank after the fuel pump nozzle
shuts off automatically.
Continued refueling may cause fuel overflow, resulting in fuel
spray and possibly a fire.

Clean all disassembled parts in the designated liquid or solvent
prior to inspection or assembly.

Replace oil seals, gaskets, packings, O-rings, locking washers, cotter pins, self-locking nuts, etc. with new
ones.

Replace inner and outer races of tapered roller bearings and needle bearings as a set.

Arrange the disassembled parts in accordance with their assembled locations and sequence.

Do not touch the terminals of electrical components which use microcomputers (such as ECM).
Static electricity may damage internal electronic components.

After disconnecting vacuum or air hoses, attach a tag to indicate the proper connection.

Use only the fluids and lubricants specified in this manual.

Use approved bonding agent, sealants or their equivalents when required.

Use hand tools, power tools (disassembly only) and recom-
mended special tools where specified for safe and efficient ser-
vice repairs.

When repairing the fuel, oil, water, vacuum or exhaust systems,
check all affected lines for leaks.

Before servicing the vehicle:
Protect fenders, upholstery and carpeting with appropriate cov-
ers.
Take caution that keys, buckles or buttons do not scratch paint.
SEF289H
SGI233
PBIC0190E
SGI234