battery NISSAN TEANA 2003 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2003, Model line: TEANA, Model: NISSAN TEANA 2003Pages: 3502, PDF Size: 74.56 MB
Page 2982 of 3502
MA-4
DESCRIPTION
DESCRIPTIONPFP:00000
Pre-Delivery Inspection ItemsBLS0005D
Shown below are Pre-delivery Inspection Items required for the new vehicle. It is recommended that
necessary items other than those listed here be added, paying due regard to the conditions in each
country.
Perform applicable items on each model. Consult text of this section for specifications.
UNDER HOOD — engine off
Radiator coolant level and coolant hose connections for leaks
Battery fluid level, specific gravity and conditions of battery terminals
Drive belts tension
Fuel lines and connections for leaks
Engine oil level and oil leaks
Brake reservoir fluid level and fluid lines for leaks
Windshield and rear window washer and headlamp cleaner reservoir fluid level
Power steering reservoir fluid level and hose connections for leaks
ON INSIDE AND OUTSIDE
Remove front spring/strut spacer (If applicable)
Operation of all instruments, gauges, lights and accessories
Operation of horn(s), wiper and washer
Steering lock for operation
Check air conditioner for gas leaks
Front and rear seats, and seat belts for operation
All moldings, trims and fittings for fit and alignment
All windows for operation and alignment
Hood, trunk lid, door panels for fit and alignment
Latches, keys and locks for operation
Weatherstrips for adhesion and fit
Headlamp aiming
Tighten wheel nuts (Inc. inner nuts if applicable)
Tire pressure (Inc. spare tire)
Check front wheels for toe-in
Install clock/voltmeter/room lamp fuse (If applicable)
Install deodorizing filter to air conditioner (If applicable)
Remove wiper blade protectors (If applicable)
UNDER BODY
Transfer and differential gear oil level
Brake and fuel lines and oil/fluid reservoirs for leaks
Tighten bolts and nuts of steering linkage and gear box, suspension, propeller shafts and drive shafts
Tighten rear body bolts and nuts (Models with wooden bed only)
ROAD TEST
Clutch operation
Parking brake operation
Service brake operation
Automatic transmission/transaxle shift timing and kickdown
Steering control and returnables
Engine performance
Page 2985 of 3502
GENERAL MAINTENANCE
MA-7
C
D
E
F
G
H
I
J
K
MA
B
MA
UNDER THE HOOD AND VEHICLE
The maintenance items listed here should be checked periodically e.g. each time you check the engine oil or refuel.
Item Reference page
Windshield washer
fluidCheck that there is adequate fluid in the tank. —
Engine coolant levelCheck the coolant level when the engine is cold.MA-25
Engine oil levelCheck the level after parking the vehicle (on level ground) and turning off the
engine.MA-30
Brake fluid levelMake sure that the brake fluid level is between the “MAX” and “MIN” lines on the
reservoir.MA-40
BatteryCheck the fluid level in each cell. It should be between the “MAX” and “MIN”
lines.—
Fluid leaksCheck under the vehicle for fuel, oil, water or other fluid leaks after the vehicle
has been parked for a while. Water dripping from the air conditioner after use is
normal. If you should notice any leaks or gasoline fumes are evident, check for
the cause and correct it immediately.—
Page 3035 of 3502
PG-1
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION PG
A
B
PG
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS
POWER SUPPLY ROUTING CIRCUIT ...................... 3
Schematic ................................................................ 3
Wiring Diagram — POWER — ................................. 4
BATTERY POWER SUPPLY — IGNITION SW.
IN ANY POSITION ................................................ 4
ACCESSORY POWER SUPPLY — IGNITION
SW. IN “ACC” OR “ON” ....................................... 10
IGNITION POWER SUPPLY — IGNITION SW.
IN “ON” AND/OR “START” ................................... 11
Fuse ....................................................................... 16
Fusible Link ............................................................ 16
Circuit Breaker ....................................................... 16
IPDM E/R (INTELLIGENT POWER DISTRIBUTION
MODULE ENGINE ROOM) ...................................... 17
System Description ................................................ 17
SYSTEMS CONTROLLED BY IPDM E/R ........... 17
FAIL-SAFE CONTROL ........................................ 17
IPDM E/R STATUS CONTROL ........................... 18
CAN Communication System Description .............. 18
CAN Communication Unit ...................................... 18
Function of Detecting Ignition Relay Malfunction ... 18
CONSULT-II Function (IPDM E/R) ......................... 19
CONSULT-II BASIC OPERATION ....................... 19
SELF-DIAG RESULTS ........................................ 19
DATA MONITOR ................................................. 19
ACTIVE TEST ..................................................... 20
Auto Active Test ..................................................... 21
DESCRIPTION .................................................... 21
OPERATION PROCEDURE ............................... 21
INSPECTION IN AUTO ACTIVE TEST MODE ... 22
Schematic .............................................................. 24
IPDM E/R Terminal Arrangement ........................... 25
Check IPDM E/R Power Supply and Ground Circuit ... 26
Inspection With CONSULT-II (Self-Diagnosis) ....... 27
Removal and Installation of IPDM E/R ................... 28
REMOVAL ........................................................... 28
INSTALLATION ................................................... 28GROUND ................................................................... 29
Ground Distribution ................................................. 29
MAIN HARNESS ................................................. 29
ENGINE ROOM HARNESS(LH) ......................... 33
ENGINE ROOM HARNESS(RH) ......................... 35
ENGINE CONTROL HARNESS/VQ ENGINE
MODELS ............................................................. 36
ENGINE CONTROL HARNESS/QR ENGINE
MODELS ............................................................. 37
BODY HARNESS ................................................ 38
BODY NO. 2 HARNESS ..................................... 40
HARNESS ................................................................. 42
Harness Layout ...................................................... 42
HOW TO READ HARNESS LAYOUT ................. 42
OUTLINE ............................................................. 43
MAIN HARNESS ................................................. 44
ENGINE ROOM HARNESS(LH) ......................... 47
ENGINE ROOM HARNESS(RH) ......................... 49
ENGINE CONTROL HARNESS(VQ ENGINE) ... 51
ENGINE CONTROL HARNESS(QR ENGINE) ... 53
BODY HARNESS ................................................ 55
BODY NO. 2 HARNESS ..................................... 57
ROOM LAMP HARNESS .................................... 59
TAIL HARNESS ................................................... 60
FRONT DOOR HARNESS .................................. 61
REAR DOOR HARNESS .................................... 62
Wiring Diagram Codes (Cell Codes) ...................... 63
ELECTRICAL UNITS LOCATION ............................ 67
Electrical Units Location ......................................... 67
ENGINE COMPARTMENT .................................. 67
PASSENGER COMPARTMENT ......................... 68
LUGGAGE COMPARTMENT .............................. 70
HARNESS CONNECTOR ......................................... 71
Description .............................................................. 71
HARNESS CONNECTOR (TAB-LOCKING
TYPE) .................................................................. 71
HARNESS CONNECTOR (SLIDE-LOCKING
TYPE) .................................................................. 72
HARNESS CONNECTOR (LEVER LOCKING
TYPE) .................................................................. 73
Page 3038 of 3502
PG-4
POWER SUPPLY ROUTING CIRCUIT
Wiring Diagram — POWER —BKS0024J
BATTERY POWER SUPPLY — IGNITION SW. IN ANY POSITION
TKWM4686E
Page 3060 of 3502
PG-26
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
Check IPDM E/R Power Supply and Ground CircuitBKS002F3
1. CHECK FUSES AND FUSIBLE LINK
Check for blown fuses and fusible link.
OK or NG
OK >> GO TO 2.
NG >> If fuse or fusible link is blown, be sure to eliminate cause of malfunction before installing new fuse
or fusible link.
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Check voltage between IPDM E/R harness connector and
ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK GROUND CIRCUIT
1. Disconnect IPDM E/R harness connectors.
2. Check continuity between IPDM E/R harness connectors and
ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.
Terminal No. Power source Fuse and fusible link No.
1
BatteryE
2C
—71
78
Terminals
Vo l ta g e (+) (-)
IPDM E/R connector Terminal
Ground
E31
Battery voltage
2
PKIB6562E
IPDM E/R connector Terminal
GroundContinuity
E8 38
E950
Ye s
60
SKIB8836E
Page 3115 of 3502
PS-1
POWER STEERING SYSTEM
G STEERING
CONTENTS
C
D
E
F
H
I
J
K
L
M
SECTION PS
A
B
PS
POWER STEERING SYSTEM
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 3
OPERATION PROCEDURE ................................. 3
Precautions for Steering System .............................. 4
PREPARATION ........................................................... 5
Special Service Tools ............................................... 5
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING ................................................ 6
NVH Troubleshooting Chart ..................................... 6
POWER STEERING FLUID ........................................ 7
Checking Fluid Level ................................................ 7
Checking Fluid Leakage ........................................... 7
Air Bleeding Hydraulic System ................................. 7
STEERING WHEEL .................................................... 9
On-Vehicle Inspection and Service .......................... 9
CHECKING CONDITION OF INSTALLATION ...... 9
CHECKING STEERING WHEEL PLAY ................ 9
CHECKING NEUTRAL POSITION STEERING
WHEEL ................................................................. 9
CHECKING STEERING WHEEL TURNING
FORCE .................................................................. 9
CHECKING FRONT WHEEL TURNING ANGLE ... 10
Removal and Installation ......................................... 11
REMOVAL ............................................................ 11
INSTALLATION .................................................... 11
STEERING COLUMN ............................................... 12
Removal and Installation ........................................ 12
COMPONENTS .................................................. 12
REMOVAL ........................................................... 12
INSPECTION AFTER REMOVAL ....................... 13
INSTALLATION ................................................... 14INSPECTION AFTER INSTALLATION ................ 14
Disassembly and Assembly .................................... 15
COMPONENTS ................................................... 15
DISASSEMBLY ................................................... 15
INSPECTION AFTER DISASSEMBLY ................ 15
ASSEMBLY ......................................................... 15
INSPECTION AFTER ASSEMBLY ...................... 16
POWER STEERING GEAR AND LINKAGE ............ 17
Removal and Installation ........................................ 17
COMPONENTS ................................................... 17
REMOVAL ........................................................... 17
INSTALLATION ................................................... 19
INSPECTION AFTER INSTALLATION ................ 19
Disassembly and Assembly .................................... 20
COMPONENTS ................................................... 20
DISASSEMBLY ................................................... 21
INSPECTION AFTER DISASSEMBLY ................ 23
ASSEMBLY ......................................................... 24
POWER STEERING OIL PUMP ............................... 29
On-Vehicle Inspection and Service ......................... 29
CHECKING RELIEF OIL PRESSURE ................ 29
Removal and Installation ........................................ 30
REMOVAL ........................................................... 30
INSTALLATION ................................................... 30
Disassembly and Assembly (Except for QR20DE
Models) ................................................................... 31
COMPONENTS ................................................... 31
INSPECTION BEFORE DISASSEMBLY ............. 31
DISASSEMBLY ................................................... 31
INSPECTION AFTER DISASSEMBLY ................ 32
ASSEMBLY ......................................................... 33
Disassembly and Assembly (QR20DE Models) ..... 35
COMPONENTS ................................................... 35
INSPECTION BEFORE DISASSEMBLY ............. 35
DISASSEMBLY ................................................... 35
INSPECTION AFTER DISASSEMBLY ................ 36
ASSEMBLY ......................................................... 37
HYDRAULIC LINE .................................................... 39
Removal and Installation ........................................ 39
COMPONENTS (EXCEPT FOR QR20DE MOD-
Page 3117 of 3502
PRECAUTIONS
PS-3
C
D
E
F
H
I
J
K
L
MA
B
PS
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BGS0004B
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions Necessary for Steering Wheel Rotation After Battery DisconnectBGS0004C
NOTE:
This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT
SYSTEM).
Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″LOCK″ position.
Always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing
work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-II.
Page 3166 of 3502
RF-2
PRECAUTIONS
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BIS0010L
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions BIS0010M
Disconnect both battery cables in advance.
Do not tamper with or force air bag lid open, as this may adversely affect air bag performance.
Be careful not to scratch pad and other parts.
When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which
may get in the way with cloth.
When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.
Keep removed parts protected with cloth.
If a clip is deformed or damaged, replace it.
If an unreusable part is removed, replace it with a new one.
Tighten bolts and nuts firmly to the specified torque.
After re-assembly has been completed, make sure each part functions correctly.
Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
Do not use any organic solvent, such as thinner or benzine.
Page 3176 of 3502
RF-12
SUNROOF
The operation condition is the following.
automatic close operation and tilt down when ignition switch is in the ON position
automatic close operation and tilt down during retained power operation.
MEMORY RESET PROCEDURE
1. Please observe the following instructions while confirming the sunroof operation.
NOTE:
Do not disconnect the electronic power while the sunroof is operating or within 5 seconds after the sunroof
stops.
2. Initialization of system should be conducted after the following conditions.
When the battery is out or connector is disconnected while sunroof is operating or within 5 seconds
after sunroof stops.
When the sunroof motor is changed.
When the sunroof does not operate normally. (Incomplete initialization conditions)
INITIALIZATION PROCEDURE
If the sunroof does not close or open automatically, use the following procedure to return sunroof operation to
normal.
1. Press and hold the switch to the CLOSE/UP side for approximately 10 seconds.
2. The glass lid will move toward tilt up direction and will be stopped mechanically, and then it will be auto-
matically fully closed. Then glass lid will be automatically operated in sequence of “tilt up” → “tilt down” →
“slide open” → “slide close”. (Keep pressing the switch during this operation)
3. After the glass lid stops, release the switch after 5 seconds.
4. If sunroof switch operates normally, this initialization is done.
Page 3178 of 3502
RF-14
SUNROOF
Terminals and Reference Value for BCMBIS0010U
Terminals and Reference Value for Sunroof Motor AssemblyBIS0010V
Te r m i n a lWire
colorItemSignal
Input/OutputConditionVoltage (V)
(Approx.)
38 RIgnition switch ON power supply
(ON or START)Input Ignition switch (ON or START position) Battery voltage
42 Y/R Power source (Fuse) Input — Battery voltage
52 B Ground — — 0
53 L/W RAP signal OutputIgnition switch ON Battery voltage
Within 15 minutes after ignition switch is
turned to OFF positionBattery voltage
When front door (driver side) is open in
retained power is operates.0
54 R/Y Power window power supply Output — Battery voltage
55 W/B Power source (Fusible link) Input — Battery voltage
62 SBFront door switch driver side
signalInputOPEN (ON) 0
CLOSE (OFF) Battery voltage
Te r m i -
nalWire
colorItemSignal
Input/OutputConditionVoltage (V)
(Approx.)
1L/BSunroof (BIT 3) switch
signalInputIgnition switch ON and sunroof switch
in TILT DOWN / SLIDE OPEN position0
Other than above Battery voltage
2 B Ground — — 0
3 G/R Timer signal InputIgnition switch ON Battery voltage
Within 15 minutes after ignition switch
is turned to OFF positionBattery voltage
When front door (driver side) is open in
retained power is operates0
4GVehicle speed signal
(2-pulse)InputSpeedometer operated [When vehicle
speed is approx. 40 km/h (25 MPH)]
5L/RSunroof (BIT 4) switch
signalInputIgnition switch ON and sunroof switch
in TILT UP / SLIDE CLOSE position0
Other than above Battery voltage
6W/BPower window power
supply Input — Battery voltage
ELF1080D