lock NISSAN TEANA 2003 Service Manual

REAR SEAT
SE-115
C
D
E
F
G
H
J
K
L
MA
B
SE

1. Seatback mat 2. Head rest 3. Head rest holder (free)
4. Head rest holder (locked) 5. Seatback trim (LH) 6. Seatback trim (RH)
7. Seatback pad 8. Bolt 9. Seatback under trim
10. Seatback under pad 11. Seat cushion trim 12. Seat cushion pad
13. Seat heater unit 14. Armrest 15. Armrest screw
16. Bush 17. Bolt 18. Armrest bracket
19. Cup holder 20. Heater switch (RH) 21. Seat switch
22. Heater switch (LH) 23. Audio switch 24. Armrest lid
25. Screw 26. Seatback screen 27. Seatback center bracket
28. Bolt 29. Nut 30. Heater control unit

TROUBLE DIAGNOSIS
SRS-33
C
D
E
F
G
I
J
K
L
MA
B
SRS

Trouble Diagnosis: “AIR BAG” Warning Lamp Does Not Turn OFFBHS0004C
DIAGNOSTIC PROCEDURE 7
1. CHECK THE DEPLOYMENT OF AIR BAG MODULE
Is air bag module deployed?
YES or NO
YES >> Refer to SRS-55, "COLLISION DIAGNOSIS" .
NO >> GO TO 2.
2. CHECK THE AIR BAG FUSE
Check 10A fuse [No.13, located in fuse block (J/B)].
Refer to PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
OK or NG
OK >> GO TO 4.
NG >> GO TO 3.
3. CHECK AIR BAG FUSE AGAIN
Replace “AIR BAG” fuse and turn ignition switch ON.
Does the
“AIR BAG” fuse blow again?
YES >> Repair or replace main harness.
NO >>INSPECTION END
4. CHECK DIAGNOSIS SENSOR UNIT
Connect CONSULT-II and touch “START”.
Is
“AIR BAG” displayed on CONSULT-ll?
YES >> GO TO 5.
NO >> Visually check the wiring harness connection of diagno-
sis sensor unit. If the harness connection check result is
OK, replace diagnosis sensor unit.
5. CHECK HARNESS CONNECTION
Is harness connection between warning lamp and diagnosis sensor unit OK?
OK or NG
OK >> Replace diagnosis sensor unit.
NG >> Connect “AIR BAG” warning lamp and diagnosis sensor unit connector properly. If “AIR BAG”
warning lamp still does not go off, replace harness.
BCIA0030E

SRS-34
TROUBLE DIAGNOSIS

Trouble Diagnosis: “AIR BAG” Warning Lamp Does Not Turn ONBHS0004D
DIAGNOSTIC PROCEDURE 8
1. CHECK “METER” FUSE
Check 10A fuse [No.14, located in fuse block (J/B)].
Refer to PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
OK or NG
OK >> GO TO 3.
NG >> GO TO 2.
2. CHECK “METER” FUSE AGAIN
Replace 10A fuse [No.14, located in fuse block (J/B)] and turn ignition switch ON.
Does the meter fuse blow again?
YES >> Repair or replace the related harness.
NO >>INSPECTION END
3. CHECK HARNESS CONNECTION BETWEEN DIAGNOSIS SENSOR UNIT AND COMBINATION
METER
Disconnect diagnosis sensor unit connector and turn ignition switch ON.
Does
“AIR BAG” warning lamp turn ON?
YES >> Replace diagnosis sensor unit.
NO >> Replace combination meter assembly.

DRIVER AIR BAG MODULE
SRS-35
C
D
E
F
G
I
J
K
L
MA
B
SRS

DRIVER AIR BAG MODULEPFP:K8510
Removal and InstallationBHS0004E
REMOVAL
CAUTION:

Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.

Always work from the side of driver air bag module.
1. Remove the side lids.
2. Remove the right and left side TORX bolts (T30).
3. Lift up the driver air bag module.
4. Disconnect the air bag harness connector, and remove the
driver air bag module.
CAUTION:

For installing / removing driver air bag module connector,
insert thin screwdriver wrapped in tape into notch, lift
lock and remove connector.

Install connector with lock raised, and push lock into
connector.
PHIA0592E
1. Driver air bag module 2. Steering wheel 3. TORX bolt (T30)
4. Side lid
PHIA0593E
PHIA0308E

SPIRAL CABLE
SRS-37
C
D
E
F
G
I
J
K
L
MA
B
SRS

SPIRAL CABLEPFP:25554
Removal and InstallationBHS0004F
REMOVAL
CAUTION:
Before servicing SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 min-
utes.
1. Remove the driver air bag module. Refer to SRS-35, "
Removal and Installation" .
2. Remove horn switch connector.
3. Set the steering wheel in the neutral position.
4. Remove the steering wheel. Refer to PS-11, "
Removal and Installation" .
5. Remove the steering column covers. Refer to IP-16, "
(S) Steering Column Upper / Lower Cover" .
6. Remove the wiper and washer switch, lighting and turn signal switch from spiral cable.
CAUTION:

Do not disassemble spiral cable.

Do not apply lubricant to the spiral cable.
PHIA1341E
1. Steering wheel 2. Spiral cable 3. Driver air bag module connector
4. Screw 5. Wiper and washer switch 6. Lighting and turn signal switch
7. Steering column assembly 8. Steering column cover 9. Steering lock escutcheon
PHIA0597E

SRS-38
SPIRAL CABLE

7. Disconnect the horn switch connector and spiral cable connec-
tor.
NOTE:
Disconnect the horn switch connector, and then the spiral cable
connector.
CAUTION:
Do not tap or bump the steering wheel.
8. Loosen screws. While pushing upper plastic tab, remove spiral cable.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

If it is mounted in the inappropriate position, spiral cable
may be cut when performing steering operation.

Also, with the steering linkage disconnected the cable may
snap by turning the steering wheel beyond the limited num-
ber of turns. The spiral cable can be turned counterclock-
wise about 2.5 turns from the right end position.

Do not twist spiral cable freely or excessively after it
becomes tight (doing so may cause the cable to be torn
off).

Secure air bag harness to the harness fixing hook.

Check SRS air bag warning lamp to make sure that the sys-
tem works normally after finishing work.

If SRS air bag warning lamp indicates a DTC exists, reset
with self-diagnosis and erase the memory using CONSULT-
II.

After the operation above, if SRS air bag warning lamp still
shows a non-standard condition, perform system trouble
diagnosis again, and repair or replace the indicated compo-
nent. Refer to SRS-16, "
SRS Operation Check" .
SHIA0193E
PHIA0599E

SRS-48
DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER

DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONERPFP:00014
Caution for Air Bag Module and Seat Belt Pre-TensionerBHS0004N

Before disposing of air bag module and seat belt pre-tensioner, or vehicles equipped with such systems,
deploy the systems. If such systems have already been deployed due to an accident, dispose of them as
indicated in SRS-48, "
DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER" .

When deploying the air bag module and seat belt pre-tensioner, always use the Special Service Tool;
Deployment tool (KV99106400).

When deploying the air bag module and seat belt pre-tensioner, stand at least 5 m (16 ft) away from the
deployment component.

When deploying air bag module and seat belt pre-tensioner, a fairly loud noise is made, followed by
smoke being released. The smoke is not poisonous, however, be careful not to inhale smoke since it irri-
tates the throat and can cause choking.

Always activate one air bag module at a time.

Due to heat, leave air bag module unattended for more than 30 minutes after deployment. Also leave seat
belt pre-tensioner unattended for more than 10 minutes after deployment.

Be sure to wear gloves when handling a deployed air bag module and seat belt pre-tensioner.

Never apply water to the deployed air bag module and seat belt pre-tensioner.

Wash your hands clean after finishing work.

Place the vehicle outdoors with an open space of at least 6 m (20 ft) on all sides when deploying air bag
module and seat belt pre-tensioner while mounted in vehicle.

Use a voltmeter to make sure the vehicle battery is fully charged.

Do not dispose the air bag module and seat belt pre-tensioner undeployed.
CHECKING DEPLOYMENT TOOL
Connecting to Battery
CAUTION:
The battery must show voltage of 9.6V or more.
Remove the battery from the vehicle and place it on dry wood blocks
approximately 5 m (16 ft) away from the vehicle.

Wait 3 minutes after the vehicle battery is disconnected before
proceeding.

Connect red clip of deployment tool to battery positive terminal
and black clip to negative terminal.
Make sure the polarity is correct. The right side lamp in the tool,
marked “deployment tool power”, should glow with a green
light. If the right side lamp glows red, reverse the connections
to the battery.
Deployment Tool Check
Press the deployment tool switch to the ON position. The left side
lamp in the tool, marked “air bag connector voltage” should illumi-
nate. If it does not illuminate, replace the tool.
PHIA0003E
SBF266H

SRS-50
DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER

Deployment of Front Passenger Air Bag Module (Outside of Vehicle)
1. Firmly secure air bag module bracket (SST: KV99105300) in a
vise.
2. Match the hole in air bag module bracket (held in vise) and front
passenger air bag module and fix them with one bolt [M8 × 25 -
30 mm (0.98 - 1.18 in)].
CAUTION:
If a gap exists between front passenger air bag module and
air bag module bracket, use a piece of wooden block
inserted in the gap to stabilize the air bag module.
3. Connect deployment tool (SST: KV99106400) and deployment
tool adapter (SST: KV99108300) to front passenger air bag
module connector.
4. Connect red clip of deployment tool to battery positive terminal
and black clip to negative terminal.
5. The lamp on the right side of the tool, marked “deployment tool
power”, should glow green, not red.
6. Press the button on the deployment tool. The left side lamp on
the tool, marked “air bag connector voltage”, will illuminate and
the air bag module will deploy.
CAUTION:

When deploying the front passenger air bag module, do not
stand on the deploying side.

Stand at least 5 m (16 ft) away from the air bag module.
SRS232-E
PHIA0609E
PHIA0610E
SRS020-A

WW-2 INSTALLATION .................................................... 38
Removal and Installation of Front Washer Pump ... 39
REMOVAL ........................................................... 39
INSTALLATION .................................................... 39
HEADLAMP WASHER .............................................. 40
Components Parts and Harness Connector Loca-
tion .......................................................................... 40
System Description ................................................. 40
OUTLINE ............................................................. 40
HEADLAMP WASHER OPERATION .................. 41
INTERLOCKED OPERATION WITH FRONT
WINDOW WASHER ............................................ 41
COMBINATION SWITCH READING FUNCTION ... 41
Schematic ............................................................... 42
Wiring Diagram — HLC — ..................................... 43
Terminals and Reference Values for BCM .............. 46
Terminals and Reference Values for IPDM E/R ...... 48
How to Proceed with Trouble Diagnosis ................. 48
Preliminary Check .................................................. 49
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 49
CONSULT-II Functions (BCM) ................................ 50
CONSULT-II BASIC OPERATION ....................... 50
DATA MONITOR .................................................. 50
ACTIVE TEST ..................................................... 51
CONSULT-II Functions (IPDM E/R) ........................ 52
CONSULT-II BASIC OPERATION ....................... 52
DATA MONITOR .................................................. 52
ACTIVE TEST ..................................................... 52Headlamp Washer Does Not Operate .................... 53
Removal and Installation of Headlamp Washer Noz-
zle ........................................................................... 57
REMOVAL ............................................................ 57
INSTALLATION .................................................... 57
Adjustment .............................................................. 57
Removal and Installation of Washer Tank ............... 58
Removal and Installation of Headlamp Washer
Tube Connector ...................................................... 58
REMOVAL ........................................................... 58
INSTALLATION ................................................... 58
Removal and Installation of Headlamp Washer
Pump ....................................................................... 58
REMOVAL ........................................................... 58
INSTALLATION ................................................... 58
Removal and Installation of Headlamp Washer
Switch ..................................................................... 58
Washer Tube Layout ............................................... 59
CIGARETTE LIGHTER ............................................. 60
Wiring Diagram — CIGAR — .................................. 60
Removal and Installation ......................................... 61
REMOVAL ............................................................ 61
INSTALLATION .................................................... 61
HORN ........................................................................ 62
Wiring Diagram — HORN — .................................. 62
Removal and Installation ......................................... 63
REMOVAL ............................................................ 63
INSTALLATION .................................................... 63

WW-4
FRONT WIPER AND WASHER SYSTEM

FRONT WIPER AND WASHER SYSTEMPFP:28810
Components Parts and Harness Connector LocationBKS001TF
System DescriptionBKS001TG

BCM (Body Control Module) controls front wiper low, high and intermittent operation.

IPDM E/R (Intelligent Power Distribution Module Engine Room) operates front wiper motor according to
CAN communication signals from BCM.
Power is supplied at all times

to ignition relay (located in IPDM E/R), from battery direct,

through 50 A fusible link (letter M, located in fuse and fusible link block)

to BCM terminal 55,

through 15 A fuse [No. 17, located in fuse block (J/B)]

to BCM terminal 42,

through 20 A fuse (No. 73, located in IPDM E/R)

to front wiper relay (located in IPDM E/R),

through 15 A fuse (No. 78, located in IPDM E/R)

to CPU (central processing unit) located in IPDM E/R,

through 15 A fuse (No. 71, located in IPDM E/R)

to CPU located in IPDM E/R.
When the ignition switch ON or START position, power is supplied

to ignition relay (located in IPDM E/R),

through 10 A fuse [No. 1, located in fuse block (J/B)]

to BCM terminal 38,
PKIA9954E