headlamp NISSAN TEANA 2003 Repair Manual

HEADLAMP - XENON TYPE -
LT-37
C
D
E
F
G
H
I
J
L
MA
B
LT

Disassembly and AssemblyBKS001NI
DISASSEMBLY
1. Turn plastic cap counterclockwise and unlock it.
2. Turn xenon bulb socket counterclockwise, and unlock it.
3. Unlock retaining spring, and remove xenon bulb (high/low).
4. Remove HID control unit screws.
5. Disconnect connectors and ground screw from the HID control unit.
6. Remove xenon bulb socket from headlamp housing assembly.
7. Disconnect bending lamp bulb socket.
8. Unlock retaining spring and remove bending lamp bulb.
9. Turn parking lamp bulb socket counterclockwise and unlock it.
10. Remove parking lamp bulb from its socket.
11. Turn front turn signal lamp bulb socket counterclockwise and unlock it.
12. Remove front turn signal lamp bulb from its socket.
ASSEMBLY
Note the following, and assembly is the reverse order of disassembly.
CAUTION:

When HID control unit is removed, reinstall it securely and avoid any looseness.

After installing bulb, be sure to install plastic cap and bulb socket securely to insure watertight-
ness.
1. Retaining spring 2. Parking lamp bulb 3. Parking lamp bulb socket
4. Bending lamp bulb 5. Seal packing 6. Bending lamp bulb socket
7. Plastic cap 8. Front turn signal lamp bulb 9. Front turn signal lamp bulb socket
10. Plastic cap 11. Seal packing 12. Xenon bulb socket (high/low)
13. Xenon bulb (high/low) 14. Ground screw 15. Seal packing
16. HID control unit 17. HID control unit mounting screw 18. Headlamp housing assembly
:N·m (kg-m, in-lb)
: Always replace after every disassembly.
PKIC9270J
HID control unit mounting screw : 3.2 N·m (0.32 kg-m, 28 in-lb)

LT-38
HEADLAMP - HALOGEN TYPE -

HEADLAMP - HALOGEN TYPE -PFP:26010
Component Parts and Harness Connector LocationBKS001NJ
System DescriptionBKS001NK

BCM (Body Control Module) controls low beam headlamp and high beam headlamp operation.

IPDM E/R (Intelligent Power Distribution Module Engine Room) operates headlamp bulbs according to
CAN communication signals from BCM.

Unified meter and A/C amp. operates high beam indicator lamp according to CAN communication signals
from BCM.
OUTLINE
Power is supplied at all times

to headlamp high relay (located in IPDM E/R)

to headlamp low relay (located in IPDM E/R) and

to ignition relay (located in IPDM E/R), from battery direct,

through 15A fuse (No. 71, located in IPDM E/R)

to CPU (central processing unit) in IPDM E/R,

through 15A fuse (No. 78, located in IPDM E/R)

to CPU in IPDM E/R,

through 50A fusible link (letter M, located in fuse and fusible link block)

to BCM terminal 55,

through 15A fuse [No. 17, located in fuse block (J/B)]

to BCM terminal 42 and

to combination meter terminal 7.
PKID0043E

HEADLAMP - HALOGEN TYPE -
LT-39
C
D
E
F
G
H
I
J
L
MA
B
LT

With the ignition switch in the ON or START position, power is supplied

to ignition relay (located in IPDM E/R),

through 10A fuse [No. 1, located in fuse block (J/B)]

to BCM terminal 38,

through 10A fuse [No. 14, located in fuse block (J/B)]

to combination meter terminal 8.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in fuse block (J/B)]

to BCM terminal 11.
Ground is supplied

to BCM terminal 52 and

to combination meter terminals 10, 11 and 12

through grounds M71 and M72,

to IPDM E/R terminals 38 and 60

through grounds E1 and E31.
LOW BEAM OPERATION
When the lighting switch is in 2ND position, BCM detects the HEAD LAMP1 and 2 (ON) by BCM combination
switch reading function. BCM sends low beam request signal (ON) through CAN communication.
When receiving low beam request signal (ON), IPDM E/R turns ON headlamp low relay in IPDM E/R. IPDM E/
R supplies power

through 15A fuse (No. 76, located in IPDM E/R)

through IPDM E/R terminal 20

to front combination lamp RH terminal 1,

through 15A fuse (No. 86, located in IPDM E/R)

through IPDM E/R terminal 30

to front combination lamp LH terminal 1.
Ground is supplied

to front combination lamp RH and LH terminals 5

through grounds E1 and E31.
With power and ground supplied, low beam headlamp illuminates.
HIGH BEAM OPERATION
When the lighting switch is in HIGH BEAM position and then also in 2ND position, BCM detects the HEAD
LAMP1, 2 (ON) and the HI BEAM (ON) by BCM combination switch reading function. BCM sends low beam
request signal (ON) and high beam request signal (ON) through CAN communication.
When receiving those signals, IPDM E/R turns ON headlamp low relay and headlamp high relay in IPDM E/R.
IPDM E/R supplies power

through 15A fuse (No. 76, located in IPDM E/R)

through IPDM E/R terminal 20

to front combination lamp RH terminal 1,

through 15A fuse (No. 86, located in IPDM E/R)

through IPDM E/R terminal 30

to front combination lamp LH terminal 1,

through 10A fuse (No. 72, located in IPDM E/R)

through IPDM E/R terminal 27

to front combination lamp RH terminal 9,

through 10A fuse (No. 74, located in IPDM E/R)

through IPDM E/R terminal 28

to front combination lamp LH terminal 9.
Ground is supplied

to front combination lamp RH and LH terminals 5, and

LT-40
HEADLAMP - HALOGEN TYPE -


to front combination lamp RH and LH terminals 10

through grounds E1 and E31.
With power and ground supplied, low beam headlamp and high beam headlamp illuminate.
Unified meter and A/C amp. receives high beam request signal (ON) through CAN communication, and makes
high beam indicator lamp turn ON in combination meter.
FLASH-TO-PASS OPERATION
When the lighting switch is in PASSING position, BCM detects the PASSING (ON) by BCM combination switch
reading function. BCM sends low beam request signal (ON) and high beam request signal (ON) through CAN
communication.
When receiving low beam request signal (ON) and high beam request signal (ON), IPDM E/R turns ON head-
lamp low relay and headlamp high relay in IPDM E/R. IPDM E/R supplies power

through 15A fuse (No. 76, located in IPDM E/R)

through IPDM E/R terminal 20

to front combination lamp RH terminal 1,

through 15A fuse (No. 86, located in IPDM E/R)

through IPDM E/R terminal 30

to front combination lamp LH terminal 1,

through 10A fuse (No. 72, located in IPDM E/R)

through IPDM E/R terminal 27

to front combination lamp RH terminal 9,

trough 10A fuse (No. 74, located in IPDM E/R)

through IPDM E/R terminal 28

to front combination lamp LH terminal 9.
Ground is supplied

to front combination lamp RH and LH terminals 5, and

to front combination lamp RH and LH terminals 10

through grounds E1 and E31.
With power and ground supplied, low beam headlamp and high beam headlamp illuminate.
Unified meter and A/C amp. receives high beam request signal (ON) through CAN communication, and makes
high beam indicator lamp turn ON in combination meter.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
EXTERIOR LAMP BATTERY SAVER CONTROL
Refer to LT- 1 9 7 , "EXTERIOR LAMP BATTERY SAVER CONTROL" .
AUTO LIGHT OPERATION
Refer to LT- 6 4 , "System Description" .
CAN Communication System DescriptionBKS001NL
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitBKS001NM
Refer to LAN-49, "CAN System Specification Chart" .

HEADLAMP - HALOGEN TYPE -
LT-41
C
D
E
F
G
H
I
J
L
MA
B
LT

SchematicBKS001NN
TKWM4829E

LT-42
HEADLAMP - HALOGEN TYPE -

Wiring Diagram — H/LAMP —BKS001NO
TKWM4574E

HEADLAMP - HALOGEN TYPE -
LT-43
C
D
E
F
G
H
I
J
L
MA
B
LT

TKWM1605E

LT-44
HEADLAMP - HALOGEN TYPE -

TKWM4575E

HEADLAMP - HALOGEN TYPE -
LT-45
C
D
E
F
G
H
I
J
L
MA
B
LT

TKWM4830E

LT-46
HEADLAMP - HALOGEN TYPE -

Terminals and Reference Values for BCMBKS001NP
CAUTION:

Check combination switch system terminal waveform under the loaded condition with lighting
switch, turn signal switch and wiper switch OFF not to be fluctuated by overloaded.

Turn wiper intermittent dial position to 4 except when checking waveform or voltage of wiper inter-
mittent dial position. Wiper intermittent dial position can be confirmed on CONSULT-II. Refer to LT-
184, "DATA MONITOR" .
Te r -
minal
No.Wire
colorSignal nameMeasuring condition
Reference value
Ignition
switchOperation or condition
2BRCombination switch
input 5ONLighting, turn,
wiper switch
(Wiper intermittent
dial position 4)OFF Approx. 0 V
Lighting switch HIGH
BEAM position
(Operates only HIGH
BEAM switch)
Approx. 1.0 V
Lighting switch 2ND
position
Approx. 2.0 V
3R/YCombination switch
input 4ONLighting, turn,
wiper switch
(Wiper intermittent
dial position 4)OFF Approx. 0 V
Any of the conditions below

Lighting switch 2ND
position

Lighting switch PASSING
position
(Operates only PASSING
switch)
Approx. 1.0 V
11 V Ignition switch (ACC) ACC — Battery voltage
PKIB4959J
PKIC4459J
PKIB4959J