glove box NISSAN TEANA 2008 Service Manual

INTELLIGENT KEY SYSTEM
DLK-29
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Key reminder has the following 3 functions.
*:If the door closing impact shocks the door lock knob or makes contact with baggage comma the door lock knob might activate the door
locks accidentally comma but unlock operation will be perform in these cases.
CAUTION:
• The above function operates when the Intelligent Key is inside the vehicle. However, there may be
times when the Intelligent Key cannot be detected, and this function will not operate when the Intelli-
gent Key is on the instrument panel, or in the glove box. Also, this system sometimes does not oper-
ate if the Intelligent Key is in the door pocket of an open door.
 Key reminder function is operated when the trunk lid is open/closed and the buzzers sound. If the
following operations are performed, the key reminder function is cleared and buzzer sounds are
stopped.
- Remote controller door lock button operation of Intelligent Key
- Remote controller door unlock button operation of Intelligent Key
- When the trunk lid is closed, the Intelligent Key is not inside the vehicle
- When any door is open
Key remainder function Operation condition Operation
Driver door closed*Right after driver side door is closed under the following conditions
 Door lock operation is performed
 Driver side door is opened
 Driver side door is in lock stateAll doors unlock
Door is open or closedRight after all doors are closed under the following conditions
 Intelligent Key is inside the vehicle
 Any door is opened
 All doors are locked by door lock and unlock switch or door lock knob All doors unlock
 Sound Intelligent Key warn-
ing buzzer
Trunk lid is closedRight after trunk lid is closed under the following conditions
 Intelligent Key is inside vehicle
 All doors are closed
 All doors are locked All doors unlock
 Trunk lid can open with trunk
lid opener switch
 Sound Intelligent Key warn-
ing buzzer

GW-14
< ON-VEHICLE REPAIR >
SIDE WINDOW GLASS
WARNING:
Always wear safety glasses and heavy gloves to prevent injury.
CAUTION:
 Be careful not to scratch the glass when removing.
 Never set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
 Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the instructions provided
with it.
 Open a door window while the urethane adhesive is curing. This prevents the glass from being forced out by
passenger room air pressure when all door windows are closed.
 The molding must be installed securely so that it is in position and leaves no clearance.
 Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (approximately 24 hours). Curing time varies with temperature and humidity.
WARNING:
 Keep heat and open flames away as primers and adhesive are flammable.
 The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never let
them come in contact with skin or eyes.
 Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.
Move immediately to an area with fresh air if affected by vapor inhalation.
 Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the side window in case of an accident.
CAUTION:
 Never use an adhesive which is past its usable term. Shelf life of this product is limited to six months
after the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the
box.
 Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
 Never leave primers or adhesive cartridge unattended with their caps open or off.
 Never drive the vehicle within 24 hours or until the urethane adhesive has completely cured. Curing
time varies depending on temperature and humidity. The curing time will increase under lower tem-
perature and lower humidity.
InspectionINFOID:0000000003825402
Repairing Water Leakage for side window glass
Leakage can be repaired without removing glass.
Determine the extent of leakage if water is leaking between the urethane adhesive material and body or glass.
This can be done by applying water to the side window glass area while pushing glass outward.
Apply primer (if necessary) and then urethane adhesive to the leakage point to stop the leakage.

GW-16
< ON-VEHICLE REPAIR >
REAR WINDOW GLASS
3. Remove rear parcel shelf finisher. Refer to INT-43, "Removal and Installation".
4. Remove partially the headlining assembly (rear edge). Refer to INT-50, "
NORMAL ROOF : Removal and
Installation"for normal roof and to INT-54, "SUNROOF : Removal and Installation" for sunroof.
5. Remove connectors and ground from the rear window defogger.
6. Remove glass using piano wire or power cutting tool (A) and an inflatable pump bag (B) after removing
molding using pliers.
NOTE:
Mark the body and the glass with matching marks if the rear window glass is reused.
WARNING:
Always wear safety glasses and heavy gloves to prevent injury.
CAUTION:
 Never use a cutting knife or power cutting tool when the rear window glass is reused.
 Be careful not to scratch the glass when removing.
 Never set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
 The dam sealant rubber should be installed in position.
 Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the instructions provided
with it.
 Open a door window while the urethane adhesive is curing. This prevents the glass from being forced out by
passenger compartment air pressure when all door windows are closed.
 Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (approximately 24 hours). Curing time varies with temperature and humidity.
WARNING:
 Keep heat and open flames away as primers and adhesive are flammable.
 The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never
let them come in contact with skin or eyes.
 Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.
Move immediately to an area with fresh air if affected by vapor inhalation.
 Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the rear window in case of an accident.
CAUTION:
 Never use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.
 Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
 Never leave primers or adhesive cartridge unattended with their caps open or off.
 Never drive the vehicle within 24 hours or until the urethane adhesive has completely cured. Cur-
ing time varies depending on temperature and humidity. The curing time increases under lower
temperature and lower humidity.
InspectionINFOID:0000000003825405
REPAIRING WATER LEAKAGE FOR REAR WINDOW GLASS
Leakage can be repaired without removing the glass.
Determine the extent of leakage if water is leaking between the urethane adhesive material and body or glass.
This can be done by applying water to the back door window glass area while pushing glass outward.
Apply primer (if necessary) and then urethane adhesive to the leakage point to stop the leakage.
PIIB5779E

INL-2
BCM (BODY CONTROL MODULE) ..................53
Reference Value .....................................................53
Wiring Diagram - BCM - .........................................76
Fail-safe ..................................................................82
DTC Inspection Priority Chart ..............................84
DTC Index ..............................................................85
SYMPTOM DIAGNOSIS .............................87
INTERIOR LIGHTING SYSTEM SYMPTOMS ...87
Symptom Table ......................................................87
PRECAUTION .............................................88
PRECAUTIONS .................................................88
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................
88
ON-VEHICLE REPAIR ................................89
MAP LAMP ........................................................89
Exploded View ........................................................89
Removal and Installation ........................................89
Replacement ..........................................................89
MOOD LAMP .....................................................90
MAP LAMP ................................................................90
MAP LAMP : Exploded View ..................................90
FRONT DOOR GRIP .................................................90
FRONT DOOR GRIP : Exploded View ...................90
FRONT DOOR GRIP : Replacement ......................90
REAR DOOR GRIP ...................................................90
REAR DOOR GRIP : Exploded View .....................91
REAR DOOR GRIP : Replacement ........................91
VANITY MIRROR LAMP ...................................92
Exploded View ........................................................92
Replacement ...........................................................92
ASHTRAY ILLUMINATION ...............................93
Exploded View ........................................................93
Replacement ...........................................................93
GLOVE BOX LAMP ...........................................94
Exploded View ........................................................94
Replacement ...........................................................94
STEP LAMP .......................................................95
Exploded View ........................................................95
Removal and Installation .........................................95
Replacement ...........................................................95
PERSONAL LAMP ............................................96
Exploded View ........................................................96
Removal and Installation .........................................96
Replacement ...........................................................96
TRUNK ROOM LAMP .......................................97
Exploded View ........................................................97
Removal and Installation .........................................97
Replacement ...........................................................97
SERVICE DATA AND SPECIFICATIONS
(SDS) ..........................................................
98
SERVICE DATA AND SPECIFICATIONS
(SDS) .................................................................
98
Bulb Specifications ..................................................98

INTERIOR ROOM LAMP CONTROL SYSTEM
INL-7
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
MA
B
INL
N
O
P
Component Parts LocationINFOID:0000000003774541
1. Personal lamp 2. Request switch 3. Step lamp
4. Door switch 5. Door lock/unlock switch 6. Push-button ignition switch illumination
7. Map lamp 8. Remote keyless entry receiver 9. BCM
10. Trunk room lamp switch 11. Trunk room lamp
A. Over the glove box B. Behind the combination meter C. Trunk lid lock assembly
D. Trunk room upward
JPLIA1126ZZ

INL-10
< FUNCTION DIAGNOSIS >
INTERIOR ROOM LAMP BATTERY SAVER SYSTEM
Component Parts Location
INFOID:0000000003774545
Component DescriptionINFOID:0000000003774546
1. Personal lamp 2. Request switch 3. Step lamp
4. Door switch 5. Door lock/unlock switch 6. Key slot
7. Map lamp 8. Vanity mirror lamp 9. Remote keyless entry receiver
10. BCM 11. Trunk room lamp switch 12. Trunk room lamp
A. Over the glove box B. Behind the combination meter C. Trunk lid lock assembly
D. Trunk room upward
JPLIA1127ZZ
Part Description
BCMOperates the interior room lamp battery saver depending on the vehicle condition to
cut the interior room lamp power supply.
Remote keyless entry receiver Receives the lock/unlock signal from keyfob.
 Transmits the lock/unlock signal to BCM.

INL-94
< ON-VEHICLE REPAIR >
GLOVE BOX LAMP
GLOVE BOX LAMP
Exploded ViewINFOID:0000000003774593
ReplacementINFOID:0000000003774594
CAUTION:
 Disconnect the battery negative terminal or remove the fuse.
 Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
 Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
GLOVE BOX LAMP BULB
1. Remove the glove box assembly. Refer to IP-11, "Exploded View".
2. Rotate the bulb socket counterclockwise and unlock it.
3. Remove the bulb.
1. Bulb 2. Bulb socket
J P L I A 111 0 Z Z

INL-98
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb SpecificationsINFOID:0000000003774604
Item Type Wattage (W)
Push-button ignition switch illumination LED —
Map lamp Wedge 8
Mood lampMap lamp
LED — Front door grip
Rear door grip
Vanity mirror lamp — 2
Ashtray illumination Wedge 1.4
Glove box lamp Wedge 1.4
Ste p l am p We dg e 2. 7
Personal lamp Wedge 8
Trunk room lamp Wedge 3.4

IP-12
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
INFOID:0000000003816778
WORK STEP
When removing instrument panel assembly, combination meter, instrument finisher A, instrument finisher B,
AV C/U (audio unit) or center console assembly take steps in the order shown by the number below.
1. Optical sensor 2. Center speaker grille 3. Sunload sensor
4. Speaker grille LH 5. Front squawker LH 6. Instrument side finisher LH
7. Side ventilator grille LH 8. Combination meter 9. Cluster lid A
10. Instrument lower panel LH 11. Fuse block lid 12. Instrument finisher A
13. Steering column upper cover 14. Steering column lower cover 15. Instrument finisher D
16. Instrument finisher E 17. Glove box lid 18. Glove box assembly
19. Glove box damper 20. Illumination lamp 21. Front passenger air bag module
22. Side ventilator grille RH 23. Instrument side finisher RH 24. Instrument panel assembly
25. Front squawker RH 26. Speaker grille RH 27. Center speaker
28. Display unit 29. Cluster lid D 30. Cluster lid upper finisher
31. AV C/U (audio unit) 32. Instrument finisher B 33. Push button ignition switch
34. Cluster lid C 35. Cluster lid lower finisher 36. Socket and bulb
37. DVD player 38. Instrument side panel RH 39. Glove box mask
Refer to GI-4, "
Components" for symbols in the figure.
PA R T SINSTRUMENT
PA N E L
ASSEMBLYCOMBINATION
METERINSTRUMENT
FINISHER AINSTRUMENT
FINISHER BAV C / U
(audio unit)CENTER
CONSOLE
ASSEMBLY
Instrument finisher D [1] [1] [1] [1]
Instrument finisher E [2] [2] [2]
Front body side welt LH [3] [2] [1] [1] [3]
Front pillar garnish LH [4]
Speaker grille LH [5]
Front squawker LH [6]
Instrument side finisher LH [7] [3] [2] [2] [4]
Fuse block lid [8] [4] [3] [3] [5]
Instrument lower panel LH [9] [5] [4] [4] [6]
Instrument lower cover LH [10][7]
Front body side welt RH [11] [5] [8]
Front pillar garnish RH [12]
Speaker grille RH [13]
Front squawker RH [14]
Instrument side finisher RH [15] [6] [9]
Glove box assembly [16] [7] [10]
DVD player [17]
Instrument side panel RH [18] [8] [11]
Instrument lower cover RH [19][12]
Selector lever knob [20][13]
Console switch panel [21][14]
Console finisher assembly [22][15]
Position indicator plate [23][16]
Console rear finisher [24][17]
Center console assembly [25][18]

IP-16
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
19. Remove glove box assembly.
 Remove glove box assembly (1) fixing screws (A).
 Open the glove box lid.
 Remove glove box assembly fixing screws (B).
 Pull back glove box assembly.
 Disconnect harness connector.
20. Remove DVD player. Refer to AV-650, "
Removal and Installation".
21. Remove instrument side panel RH.
 Remove instrument side panel RH (1) fixing screw (A).
 Pull toward the direction the arrow is pointing.
22. Remove instrument lower cover RH.
 Disengage instrument lower cover RH (1) fixing clip, pawl and
metal clips.
 Pull the instrument lower cover RH crosswise.
23. Remove selector lever knob. Refer to TM-155, "
Removal and Installation".
: Pawl
JMJIA1901ZZ
: Clip
: Pawl
JMJIA1902ZZ
: Clip
: Pawl
: Metal clip
JMJIA1903ZZ