engine NISSAN TIIDA 2010 Service Repair Manual

AT-250
< SERVICE INFORMATION >
OVERHAUL
Oil Channel
INFOID:0000000005397432
HR16DE ENGINE MODELS
19. Oil pan 20. Drain plug gasket21. Drain plug
22. Magnet 23. Oil pan bolt24. Snap ring
25. O-ring 26. O-ring27. N-D accumulator piston
28. Return spring 29. O-ring 30. Lip seal
31. Input speed sensor 32. O-ring 33. Retaining pin
34. Detent spring 35. Retaining pin 36. Manual shaft
37. Manual shaft oil seal 38. Manual plate 39. Parking rod plate
40. Parking rod 41. OD servo piston retainer42. Snap ring
43. O-ring 44. OD servo piston45. D-ring
46. Servo piston retainer 47. O-ring48. E-ring
49. Spring retainer 50. OD servo return spring 51. D-ring
52. Band servo piston 53. Band servo thrust washer 54. Band servo piston stem
55. 2nd servo return spring 56. Transmission range switch57. Parking shaft
58. Return spring 59. Thrust needle bearing60. Seal ring
61. Output shaft 62. Output shaft bearing63. Output shaft adjusting shim
64. Side cover 65. Side cover bolt 66. Lock nut
67. Idler gear 68. Idler gear bearing69. Reduction pinion gear adjusting
shim
70. Parking actuator support 71. Parking pawl 72. LH differential side oil seal
73. Output speed sensor
: Apply Genuine Anaerobic Liquid Gasket or equivalent.
Revision: January 20102010 Versa

OVERHAULAT-251
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
MR18DE ENGINE MODELS
SCIA5925E
Revision: January 20102010 Versa

OVERHAULAT-253
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
Location of Adjusting Shims, Needle Bearings and Thrust WashersINFOID:0000000005397433
HR16DE ENGINE MODELS
• Refer to AT-374, "Adjusting shims, Needle Bearings, Thrust Washers and Snap Rings".
SCIA6051J
Revision: January 20102010 Versa

AT-254
< SERVICE INFORMATION >
OVERHAUL
MR18DE ENGINE MODELS
• Refer to AT-374, "Adjusting shims, Needle Bearings, Thrust Washers and Snap Rings".
SCIA7960E
Revision: January 20102010 Versa

OVERHAULAT-255
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
Location of Snap RingsINFOID:0000000005397434
HR16DE ENGINE MODELS
• Refer to AT-374, "Adjusting shims, Needle Bearings, Thrust Washers and Snap Rings".
SCIA6170J
Revision: January 20102010 Versa

AT-256
< SERVICE INFORMATION >
OVERHAUL
MR18DE ENGINE MODELS
• Refer to AT-374, "Adjusting shims, Needle Bearings, Thrust Washers and Snap Rings".
SCIA7961E
Revision: January 20102010 Versa

AT-262
< SERVICE INFORMATION >
DISASSEMBLY
• HR16DE engine models
• MR18DE engine models
b. Remove bracket from converter housing
c. Remove converter housing by tapping it lightly.
d. Remove O-ring from differential lubricant hole.
24. Remove final drive assembly from transaxle case.
SCIA6211J
SCIA7970E
SCIA3281E
SAT228F
Revision: January 20102010 Versa

DISASSEMBLYAT-263
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
25. Remove differential side bearing outer race from transaxle case and converter housing. (MR18DE engine models)
26. Remove differential side bearing adjusting shim from transaxle case.
27. Remove RH differential side oil seal from converter housing using a suitable tool.
CAUTION:
Be careful not to scratch converter housing.
28. Remove differential lubricant tube (1) and clips (2) from con- verter housing.
: Bolt
29. Remove oil pump assembly according to the following procedures. Tool number : KV381054S0 (J-34286)
SCIA5378E
SCIA4938E
SCIA3283E
SCIA7817E
Revision: January 20102010 Versa

AT-270
< SERVICE INFORMATION >
DISASSEMBLY
41. Remove overrun clutch hub (1) from forward clutch drum.
42. Remove thrust washer (1) from overrun clutch hub (2).•Inspect thrust washer (1) and overrun clutch hub (2), and
replace if damaged or worn.
43. Remove forward clutch assembly and overrun clutch assembly (1) from transaxle case.
44. Remove needle bearing (1) and thrust washer (2) from bearing retainer.
•Inspect needle bearing (1) and thrust washer (2), and
replace damaged or worn.
45. Remove output shaft assembly according to the following procedures.
a. HR16DE engine models.
SCIA5898J
SCIA5899J
SCIA5900J
SCIA5901J
Revision: January 20102010 Versa

DISASSEMBLYAT-271
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
i. Remove side cover bolts (1), then remove side cover by lightly tapping it with a soft hammer.
CAUTION:
Be careful not to damage cover.
ii. Remove side cover gasket from side cover.
iii. Set manual shaft in "P" position to lock idler gear and output gear.
iv. Unlock both idler gear and output gear lock nuts with a suitable tool.
v. Remove idler gear and output gear lock nuts.
vi. Remove out put gear (1) and idler gear (2) using Tool (A).
vii. Removing reduction pinion gear and output shaft from transaxle case.
viii. Remove reduction pinion gear adjusting shim (1) from reduction pinion gear (2).
ix. Remove output gear adjusting spacer (3) from output shaft (4).
b. MR18DE engine models.
SCIA6039J
SAT704D
Tool number : ST27180001 (J-25726-A)
SCIA6991E
SCIA5902J
Revision: January 20102010 Versa