clock NISSAN TITAN 2015 1.G User Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2015, Model line: TITAN, Model: NISSAN TITAN 2015 1.GPages: 457, PDF Size: 3.77 MB
Page 340 of 457
●Do not start or run the engine while
vehicle is on the jack. It may cause the
vehicle to move. This is especially true
for vehicles with limited slip
differentials.
● Do not allow passengers to stay in the
vehicle while it is on the jack.
● Never run the engine with a wheel(s) off
the ground. It may cause the vehicle to
move.
Always refer to the illustration for the correct
placement and jack-up points for your specific
vehicle model and jack type.
Carefully read the caution label attached to
the jack body and the following instruc-
tions. 1. Loosen each wheel nut one or two turns by
turning counterclockwise with the wheel nut
wrench. Do not remove the wheel nuts
until the tire is off the ground.
WCE0152
6-6In case of emergency
Page 366 of 457
CAUTION
Oil level should be checked regularly. Op-
erating the engine with an insufficient
amount of oil can damage the engine, and
such damage is not covered by warranty.
CHANGING ENGINE OIL
1. Park the vehicle on a level surface and applythe parking brake.
2. Start the engine and let it idle until it reaches operating temperature, then turn it off. 3. Remove the oil filler cap
Aby turning it
counterclockwise.
4. Place a large drain pan under the drain plug
B.
5. Remove the drain plug
Bwith a wrench by
turning it counterclockwise and completely
drain the oil.
If the oil filter is to be changed, remove and
replace it at this time. For additional informa-
tion, refer to “Changing engine oil filter” in
this section.
● Waste oil must be disposed of prop-
erly.
● Check your local regulations.
WARNING
●Prolonged and repeated contact with
used engine oil may cause skin cancer.
● Try to avoid direct skin contact with
used oil. If skin contact is made, wash
thoroughly with soap or hand cleaner as
soon as possible.
● Keep used engine oil out of reach of
children.
LDI2610
8-10Maintenance and do-it-yourself
Page 368 of 457
CHANGING ENGINE OIL FILTER
1. Park the vehicle on a level surface and applythe parking brake.
2. Turn the engine off. 3. Remove bolts
Aand cover.
4. Place a large drain pan under the oil filter
B.
5. Loosen the oil filter with an oil filter wrench by turning it counterclockwise. Then remove
the oil filter by turning it by hand.
CAUTION
Be careful not to burn yourself. The engine
oil may be hot.
6. Wipe the engine oil filter sealing surface with a clean rag.
CAUTION
Be sure to remove any old gasket material
remaining on the sealing surface of the
engine. Failure to do so could lead to an
oil leak and engine damage.
7. Coat the gasket on the new filter with clean engine oil.
8. Screw on the oil filter until a slight resistance is felt, then tighten an additional 2/3 turn.
9. Start the engine and check for leakage around the oil filter. Correct as required.
10. Install cover in reverse order of removal. 11. Turn the engine off and wait more than
10 minutes. Check the oil level. Add engine
oil if necessary.
4WD (if so equipped)
LDI2626
8-12Maintenance and do-it-yourself
Page 385 of 457
●Do not leave the bulb out of the fog light
for a long period of time as dust, mois-
ture and smoke may enter the fog light
body and affect the performance of the
fog light.
1. Disconnect the negative (-) battery cable.
2. The fog light is accessible in front of the fronttire and behind the bumper.
3. Disconnect the bulb connector
1.
4. Rotate the bulb counterclockwise and re- move.
5. Remove by pulling it straight out of the fog light assembly. Do not shake or rotate the
bulb when removing it. Do not touch the
glass envelope.
6. Install in the reverse order of removal. NOTE:
To adjust the fog light vertical aim: Access
the aiming screw from underneath the front
bumper. The aiming screw is located on the
bottom of the fog light housing. Turn the
screw clockwise to raise the pattern. Turn
the screw counterclockwise to lower the
pattern.
LDI0382
Maintenance and do-it-yourself8-29
Page 419 of 457
Check the tightness of the tie-down cleat peri-
odically during a trip to make sure the center bolt
has not become loose.
Install the tie-down cleat as follows:1. Remove the channel protectors by sliding them out the back of the truck bed. Properly
store the channel protectors.
2. Loosen the center bolt completely.
3. Insert the cleat into the channel perpendicu-lar to the channel as shown. Then rotate the
cleat clockwise 90° and slide it to the de-
sired location.
4. Position the cleat so the nubs on the bottomfully seat into the channel detents.
LTI0103
LTI0104
Technical and consumer information9-19
Page 448 of 457
BrakeAnti-lock Braking System (ABS) ......5-34
Brake assist (for Intelligent cruise control
system)....................5-35
Brake fluid ..................8-14
Brake light (See stop light) .........8-30
Brake system .................5-33
Brake warning light .............2-13
Brake wear indicators ........2-20,8-22
Parking brake operation ...........5-20
Self-adjusting brakes ............8-22
Brake fluid ....................8-14
Brakes ......................8-22
Brake system ...................5-33
Break-in schedule ................5-22
Brightness/contrastbutton............4-9
Brightness control Instrument panel ...............2-36
Bulb replacement ................8-30
C
Capacities and recommended fuel/lubricants . .9-2
Cargolightswitch................2-38
Cargo(Seevehicleloadinginformation)....9-15
Car phone or CB radio .............4-79
CD care and cleaning ..............4-66
CD player
(See audio system) .....4-37,4-41,4-46,4-53
Checkingbulbs .................2-12
Check tire pressure ...............2-27
Child restraints .......1-24,1-24,1-25,1-27
LATCH (Lower Anchors and Tethers for
CHildren) System ..............1-27 Precautions on child
restraints
.........1-25,1-32,1-39,1-46
Top tether strap anchor point locations . .1-30
Child safety rear door lock ............3-7
Chimes,audiblereminders...........2-20
Cleaning exterior and interior ........7-2,7-4
Clock ...................4-36,4-40 (models without navigation system) ....4-40
Clockset.....................4-40
Clock set/adjustment.....4-7,4-36,4-40,4-44
C.M.V.S.S. certification label ..........9-13
Cold weather driving ...............5-39
Compact disc (CD)
player ............4-37,4-41,4-46,4-53
Console light ...................2-60
Control panel buttons ...............4-4
Back button ..................4-7
Brightness/contrast button ..........4-9
Enterbutton..................4-4
Setting button .................4-7
With navigation system .........4-4,4-5
Controls Audio controls (steering wheel) .......4-67
Heater and air conditioner controls .....4-25
Heater and air conditioner controls
(manual) ...................4-15
Coolant Capacities and recommended
fuel/lubricants .................9-2
Changingenginecoolant...........8-8
Checking engine coolant level ........8-8
Engine coolant temperature gauge .....2-5
Corrosion protection ...............7-5
Cruisecontrol...............5-20,5-21
Cupholders...................2-51
Curtainside-impactandrolloverairbag....1-62 D
Daytime running light system (Canada only) . .2-35
Defroster switch Rear window and outside mirror defroster
switch .....................2-31
Digital video disc DVD ..............4-69
Dimensionsandweights ............9-10
Dimmer switch for instrument panel ......2-36
Display...................2-20,2-21
Display controls (see control panel buttons) . .4-4
Door locks .....................3-3
Drive belt .....................8-18
Drive
positioner, Automatic ....3-25,3-26,3-27
Driving Cold weather driving .............5-39
Driving with automatic transmission ....5-14
Precautions when starting and
driving ...................5-2,5-7
E
Economy-fuel..................5-24
Electronic locking rear differential (E-Lock)
system ......................5-31
Electronic locking rear differential (E-Lock)
system switch ..................2-39
Emission control information label .......9-13
Emission control system warranty .......9-42
Engine Before starting the engine ..........5-11
Blockheater.................5-41
Capacities and recommended
fuel/lubricants.................9-2
10-2