warning light NISSAN VERSA 2006 Workshop Service Owner's Manual

LT-2Revision: June 20062007 Versa Daytime Light Control Does Not Operate Properly
(High Beam Headlamps Operate Properly) ............ 35
Aiming Adjustment .................................................. 37
PREPARATION BEFORE ADJUSTING .............. 37
LOW BEAM AND HIGH BEAM ........................... 37
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 38
Bulb Replacement .................................................. 39
HEADLAMP (HIGH/LOW) ................................... 39
PARKING (CLEARANCE) LAMP ......................... 39
FRONT TURN SIGNAL LAMP ............................ 39
Removal and Installation ........................................ 39
REMOVAL ........................................................... 39
INSTALLATION .................................................... 39
Disassembly and Assembly .................................... 40
DISASSEMBLY ................................................... 40
ASSEMBLY ......................................................... 40
FRONT FOG LAMP .................................................. 41
Component Parts and Harness Connector Location ... 41
System Description ................................................. 41
OUTLINE ............................................................. 41
FOG LAMP OPERATION .................................... 42
COMBINATION SWITCH READING FUNCTION ... 42
EXTERIOR LAMP BATTERY SAVER CONTROL ... 42
CAN Communication System Description .............. 42
Wiring Diagram — F/FOG — .................................. 43
Terminals and Reference Values for BCM .............. 45
Terminals and Reference Values for IPDM E/R ...... 45
How to Proceed With Trouble Diagnosis ................ 45
Preliminary Check .................................................. 45
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ................................................... 45
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR IPDM E/R ........................................... 45
CONSULT-II Function (BCM) .................................. 45
CONSULT-II Function (IPDM E/R) .......................... 45
Front Fog lamps Do Not Illuminate (Both Sides) .... 45
Front Fog Lamp Does Not Illuminate (One Side) ... 48
Aiming Adjustment .................................................. 49
Bulb Replacement .................................................. 49
Removal and Installation ........................................ 50
REMOVAL ........................................................... 50
INSTALLATION .................................................... 50
TURN SIGNAL AND HAZARD WARNING LAMPS ... 51
Component Parts and Harness Connector Location ... 51
System Description ................................................. 51
TURN SIGNAL OPERATION ............................... 51
HAZARD LAMP OPERATION ............................. 52
REMOTE KEYLESS ENTRY SYSTEM OPERA-
TION .................................................................... 53
COMBINATION SWITCH READING FUNCTION ... 53
CAN Communication System Description .............. 53
Schematic ............................................................... 54
Wiring Diagram — TURN — ................................... 55
Terminals and Reference Values for BCM .............. 59
How to Proceed With Trouble Diagnosis ................ 59
Preliminary Check .................................................. 59
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ................................................... 59CONSULT-II Function (BCM) ..................................59
Turn Signals Do Not Operate ..................................59
Front Turn Signal Lamp Does Not Operate ............59
Rear Turn Signal Lamp Does Not Operate .............60
Hazard Warning Lamp Does Not Operate But Turn
Signal Lamp Operates ............................................62
Turn Signal Indicator Lamp Does Not Operate .......63
Bulb Replacement of Front Turn Signal Lamp ........64
Bulb Replacement of Rear Turn Signal Lamp .........64
Removal and Installation of Front Turn Signal Lamp ...64
Removal and Installation of Rear Turn Signal Lamp ...64
LIGHTING AND TURN SIGNAL SWITCH ................65
Removal and Installation .........................................65
REMOVAL ............................................................65
INSTALLATION ....................................................65
HAZARD SWITCH .....................................................66
Removal and Installation .........................................66
REMOVAL ............................................................66
INSTALLATION ....................................................66
COMBINATION SWITCH ..........................................67
Wiring Diagram — COMBSW — ............................67
Combination Switch Reading Function ...................68
Terminals and Reference Values for BCM ..............68
CONSULT-II Function (BCM) ..................................68
Combination Switch Inspection ...............................68
Removal and Installation .........................................70
STOP LAMP ..............................................................71
Wiring Diagram — STOP/L — ................................71
Bulb Replacement of High-Mounted Stop Lamp .....72
Bulb Replacement of Rear Combination Lamp for
Stop Lamp ...............................................................72
Removal and Installation of High-Mounted Stop
Lamp .......................................................................72
REMOVAL ............................................................72
INSTALLATION ....................................................72
Removal and Installation of Rear Combination
Lamp for Stop Lamp ................................................72
BACK-UP LAMP .......................................................73
Wiring Diagram — BACK/L — ................................73
Bulb Replacement ...................................................74
Removal and Installation .........................................74
PARKING, LICENSE PLATE AND TAIL LAMPS ......75
Component Parts and Harness Connector Location ...75
System Description .................................................75
OPERATION BY LIGHTING SWITCH .................75
COMBINATION SWITCH READING FUNCTION ...76
EXTERIOR LAMP BATTERY SAVER CONTROL ...76
CAN Communication System Description ..............76
Schematic ...............................................................77
Wiring Diagram — TAIL/L — ...................................78
Terminals and Reference Values for BCM ..............81
Terminals and Reference Values for IPDM E/R ......81
How to Proceed With Trouble Diagnosis ................81
Preliminary Check ...................................................81
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ...................................................81
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR IPDM E/R ...........................................81
CONSULT-II Function (BCM) ..................................81

TURN SIGNAL AND HAZARD WARNING LAMPS
LT-51
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
TURN SIGNAL AND HAZARD WARNING LAMPSPFP:26120
Component Parts and Harness Connector LocationEKS00HXZ
System DescriptionEKS00HY0
TURN SIGNAL OPERATION
Power is supplied at all times

through 40A fusible link (letter g , located in the fuse and fusible link box)

to BCM (body control module) terminal 70,

through 10A fuse [No. 8, located in the fuse block (J/B)]

to BCM terminal 57,

through 10A fuse [No. 13, located in the fuse block (J/B)]

to combination meter terminal 27.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 6, located in fuse block (J/B)]

to BCM terminal 38,

through 10A fuse [No. 3, located in fuse block (J/B)]

to combination meter terminal 28.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 20, located in the fuse block (J/B)]

to BCM terminal 11.
Ground is supplied

to BCM terminal 67 and

to combination meter terminals 21, 22 and 23

through grounds M57 and M61.
LH Turn Signal Lamp
When the turn signal switch is moved to the left turn position, the BCM receives an input signal requesting left
turn signals to flash. The BCM then supplies power

through BCM terminal 60

to front combination lamp LH terminal 4 and

to rear combination lamp LH terminal 6.
1. BCM M18 and M20 (view with glove
box removed)2. Hazard switch M55 3. Combination switch (lighting switch)
M28
4. Combination meter M24
WKIA5493E

TURN SIGNAL AND HAZARD WARNING LAMPS
LT-59
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
Terminals and Reference Values for BCMEKS00HY5
Refer to BCS-12, "Terminals and Reference Values for BCM" .
How to Proceed With Trouble DiagnosisEKS00HY6
1. Confirm the symptom or customer complaint.
2. Understand operation description and function description. Refer to LT- 5 1 , "
System Description" .
3. Perform the preliminary check. Refer to LT-59, "
Preliminary Check" .
4. Check symptom and repair or replace the component.
5. Do turn signal and hazard warning lamps operate normally? If YES, GO TO 6. If NO, GO TO 4.
6. INSPECTION END
Preliminary CheckEKS00HY7
CHECK POWER SUPPLY AND GROUND CIRCUIT FOR BCM
Refer to BCS-16, "BCM Power Supply and Ground Circuit Check" .
CONSULT-II Function (BCM)EKS00HY8
Refer to LT- 1 2 , "CONSULT-II Function (BCM)" .
Turn Signals Do Not OperateEKS00HY9
1. CHECK COMBINATION SWITCH INPUT SIGNAL
With CONSULT-II
1. Select “BCM” on CONSULT-II. Select “FLASHER” on “SELECT
TEST ITEM” screen.
2. Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “TURN SIGNAL R” and “TURN SIGNAL L” turns
ON-OFF linked with operation of lighting switch.
Without CONSULT-II
Refer to LT- 6 8 , "
Combination Switch Inspection" .
OK or NG
OK >> Replace the BCM. BCS-25, "Removal and Installation of BCM"
NG >> Check combination switch (lighting switch). Refer to LT-68, "Combination Switch Inspection" .
Front Turn Signal Lamp Does Not OperateEKS00IXB
1. CHECK BULB
Verify the bulb standard of each turn signal lamp is correct. Refer to LT-116, "
Exterior Lamp" .
OK or NG
OK >> GO TO 2.
NG >> Replace turn signal lamp bulb. Refer to LT- 6 4 , "
Bulb Replacement of Front Turn Signal Lamp" . When turn signal switch is
right position: TURN SIGNAL R ON
When turn signal switch is
left position: TURN SIGNAL L ON
PKIA7600E

PG-20
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
Revision: June 20062007 Versa
DATA MONITOR
All Signals, Main Signals, Selection From Menu
*1 Perform monitoring of IPDM E/R data with the ignition switch ON. When the ignition switch is in ACC position, display may not be cor-
rect.
*2 This item is displayed, but does not function.
CAN DIAG SUPPORT MNTR
Refer to LAN-4, "SYSTEM DESCRIPTION" .
ACTIVE TEST
Display Item List
Item nameCONSULT-II
screen display Display or unitMonitor item selection
Description
ALL
SIGNALSMAIN
SIGNALSSELECTION
FROM MENU
Motor fan requestMOTOR FAN
REQ1/2/3/4 X X X Signal status input from ECM
Compressor
requestAC COMP REQ ON/OFF X X X Signal status input from ECM
Parking, license,
and tail lamp
requestTAIL & CLR REQ ON/OFF X X X Signal status input from BCM
Headlamp low
beam requestHL LO REQ ON/OFF X X X Signal status input from BCM
Headlamp high
beam requestHL HI REQ ON/OFF X X X Signal status input from BCM
Front fog request FR FOG REQ ON/OFF X X X Signal status input from BCM
FR wiper request FR WIP REQ STOP/1LO/LO/HI X X X Signal status input from BCM
Wiper auto stopWIP AUTO
STOPACT P/STOP P X X X Output status of IPDM E/R
Wiper protection WIP PROT OFF/LS/HS/Block X X X Control status of IPDM E/R
Starter request ST RLY REQ ON/OFF X X Status of input signal (*1)
Ignition relay
statusIGN RLY ON/OFF X X XIgnition relay status monitored
with IPDM E/R
Rear defogger
requestRR DEF REQ ON/OFF X X X Signal status input from BCM
Oil pressure
switchOIL P SW OPEN/CLOSE X XSignal status input from IPDM
E/R
Hood switch HOOD SW (*2) OFF X XSignal status input from IPDM
E/R
Theft warning
horn requestTHFT HRN REQ ON/OFF X X Signal status input from BCM
Horn chirp HORN CHIRP ON/OFF X X Output status of IPDM E/R
Daytime light
requestDTRL REQ ON/OFF X X Signal status input from BCM
Test name CONSULT-II screen display Description
Head, tail, fog lamp output EXTERNAL LAMPWith a certain ON-OFF operation (OFF, TAIL, LO, HI, FOG), the front
fog lamp, headlamp low, headlamp high RH, headlamp high LH, and
tail lamp relays can be operated.
Rear defogger output REAR DEFOGGERWith a certain ON-OFF operation, the rear defogger relay can be oper-
ated.
Front wiper (HI, LO) output FRONT WIPERWith a certain operation (OFF, HI ON, LO ON), the front wiper relays
(Lo, Hi) can be operated.

PG-22
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
Revision: June 20062007 Versa
INSPECTION IN AUTO ACTIVE TEST MODE
When auto active test mode is actuated, the following six steps are repeated three times.
(A): Oil pressure warning lamp is blinking when the auto active test is operating.
Concept of Auto Active Test

IPDM E/R actuates auto active test mode when it receives door switch signal from BCM via CAN commu-
nication line. Therefore, when auto active test mode is activated successfully, CAN communication
between IPDM E/R and BCM is normal.
WKIA5664E
Item Number Test Item Operation Time/Frequency
1 Rear window defogger 10 seconds
2 Front wipers LOW 5 seconds then HIGH 5 seconds
3 Daytime light system (Canada only) 10 seconds
3 Tail, license, and parking lamps 10 seconds
3 Front fog lamps 10 seconds
4 Headlamps (low) 20 seconds
4 Headlamps (high) ON-OFF 5 times
5 A/C compressor (magnet clutch) ON-OFF 5 times
6 Cooling fan LOW 5 seconds then HIGH 5 seconds
WKIA5665E

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
PG-23
C
D
E
F
G
H
I
J
L
MA
B
PG
Revision: June 20062007 Versa

If any of the systems controlled by IPDM E/R cannot be operated, possible cause can be easily diagnosed
using auto active test.
Diagnosis chart in auto active test mode
Symptom Inspection contents Possible cause
Rear window defogger
does not operate.Perform auto active
test. Does rear win-
dow defogger oper-
ate?YES

BCM signal input circuit
NO

Rear window defogger relay

Open circuit of rear window defogger

IPDM E/R malfunction

Harness or connector malfunction between IPDM E/R and rear window
defogger
Any of front wipers, tail
and parking lamps, front
fog lamps, daytime light
system (Canada only),
and headlamps (High,
Low) do not operate.Perform auto active
test. Does system in
question operate?YES

BCM signal input system
NO

Lamp/wiper motor malfunction

Lamp/wiper motor ground circuit malfunction

Harness/connector malfunction between IPDM E/R and system in
question

IPDM E/R (integrated relay) malfunction
A/C compressor does
not operate.Perform auto active
test. Does magnet
clutch operate?YES

BCM signal input circuit

CAN communication signal between BCM and ECM

CAN communication signal between ECM and IPDM E/R
NO

Magnet clutch malfunction

Harness/connector malfunction between IPDM E/R and magnet clutch

IPDM E/R (integrated relay) malfunction
Cooling fan does not
operate.Perform auto active
test. Does cooling fan
operate?YES

ECM signal input circuit

CAN communication signal between ECM and IPDM E/R
NO

Cooling fan motor malfunction

Harness/connector malfunction between IPDM E/R and cooling fan
motor

IPDM E/R (integrated relay) malfunction
Oil pressure warning
lamp does not operate.Perform auto active
test. Does oil pres-
sure warning lamp
blink?YES

Harness/connector malfunction between IPDM E/R and oil pressure
switch

Oil pressure switch malfunction

IPDM E/R
NO

CAN communication signal between BCM and combination meter

Combination meter

HARNESS
PG-61
C
D
E
F
G
H
I
J
L
MA
B
PG
Revision: June 20062007 Versa
Wiring Diagram Codes (Cell Codes)EKS00IW9
Use the chart below to find out what each wiring diagram code stands for.
Refer to the wiring diagram code in the alphabetical index to find the location (page number) of each wiring
diagram.
Code Section Wiring Diagram Name
ABS BRC Anti-lock Brake System
A/C,M MTC Manual Air Conditioner
APPS1 EC Accelerator Pedal Position Sensor
A/F EC Air Fuel Ratio Sensor 1
A/FH EC Air Fuel Ratio Sensor 1 Heater
APPS2 EC Accelerator Pedal Position Sensor
APPS3 EC Accelerator Pedal Position Sensor
ASC/BS EC ASCD Brake Switch
ASC/SW EC ASCD Steering Switch
ASCBOF EC ASCD Brake Switch
ASCIND EC ASCD Indicator
AT/IND DI A/T Indicator Lamp
AUDIO AV Audio
BACK/L LT Back-up Lamp
BA/FTS AT A/T Fluid Temperature Sensor and TCM Power Supply
BRK/SW EC Brake Switch
CAN AT CAN Communication Line
CAN CVT CAN Communication Line
CAN EC CAN Communication Line
CAN LAN CAN System
CHARGE SC Charging System
CHIME DI Warning Chime
COOL/F EC Cooling Fan Control
COMBSW LT Combination Switch
CVTIND DI CVT Indicator Lamp
D/LOCK BL Power Door Lock
DEF GW Rear Window Defogger
DTRL LT Headlamp - With Daytime Light System
ECTS EC Engine Coolant Temperature Sensor
ENGSS AT Engine Speed Signal
EPS STC Electronic Controlled Power Steering
ETC1 EC Electric Throttle Control Function
ETC2 EC Throttle Control Motor Relay
ETC3 EC Throttle Control Motor
F/FOG LT Front Fog Lamp
F/PUMP EC Fuel Pump
FTS AT A/T Fluid Temperature Sensor
FTS CVT CVT Fluid Temperature Sensor Circuit
FTTS EC Fuel Tank Temperature Sensor
FUEL EC Fuel Ignition System Function
HEATER MTC Heater System
H/LAMP LT Headlamp
H/PHON AV Hands Free Telephone
HORN WW Horn
HO2S2 EC Heated Oxygen Sensor 2
HO2S2H EC Heated Oxygen Sensor 2 Heater
IATS EC Intake Air Temperature Sensor

CHARGING SYSTEM
SC-29
C
D
E
F
G
H
I
J
L
MA
B
SC
Revision: June 20062007 Versa
DIAGNOSTIC PROCEDURE 1
Check Charge Warning Lamp Circuit
1. CHECK CHARGE WARNING LAMP CIRCUIT CONNECTION
Check to see if terminal 2 is clean and tight.
OK or NG
OK >> GO TO 2.
NG >> Repair terminal 2 connection. Confirm repair by performing complete Battery/Starting/Charging
system test.
2. CHECK CHARGE WARNING LAMP CIRCUIT
1. Disconnect generator connector F1.
2. Apply ground to generator connector F1 terminal 2 with the igni-
tion switch in the ON position.
OK or NG
OK >> GO TO SC-28, "WORK FLOW" .
NG >> Check the following.

10A fuse [No. 3, located in fuse block (J/B)]

CHARGE lamp

Harness for open or short between combination
meter and fuse

Harness for open or short between combination meter and generator CHARGE lamp should light up.
WKIA5577E

SRS-34
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
Trouble Diagnosis Without CONSULT-IIEHS001V5
DIAGNOSTIC PROCEDURE 6
Inspect SRS Malfunction Using "AIR BAG" Warning Lamp—Diagnosis Mode
NOTE:
SRS will not enter Diagnosis mode if no malfunction is detected in User mode.
1. Turn ignition switch ON.
2. After “AIR BAG” warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
3. Wait more than 3 seconds.
4. Repeat steps 1 to 3 two times.
5. Turn ignition switch ON.
SRS is now in Diagnosis mode.
"AIR BAG" warning lamp operates in Diagnosis mode according to the Warning Lamp Flash Code Chart:

TROUBLE DIAGNOSIS
STC-15
[EPS]
C
D
E
F
H
I
J
K
L
MA
B
STC
Revision: June 20062007 Versa
Symptom ChartUGS0008I
If EPS warning lamp turns ON, perform self-diagnosis. Refer to STC-13, "SELF-DIAG RESULTS MODE" .
Symptom Condition Check item Reference page
EPS warning lamp does not turn ON when
ignition switch to “ON”.
(EPS warning lamp check)Ignition switch: ONCAN communication line
STC-26
Combination meter
EPS warning lamp does not turn OFF for
several seconds after starting the engineEngine runningCAN communication line
STC-27
Power supply and ground for
EPS control unit
Torque sensor
EPS motor
Vehicle speed signal
Engine status signal
Combination meter
Steering wheel turning force is heavy or light,
while driving

While driving

Steering wheel turningCAN communication line
STC-29
Vehicle speed signal
Engine status signal
EPS motor
Steering wheel turning force
(Mechanical malfunction)
Unbalance steering wheel turning force and
return between right and left, while driving

While driving

Steering wheel turningWheel alignment
STC-31Steering wheel turning force
(Mechanical malfunction)
Unbalance steering wheel turning force,
while driving (Torque variation)

While driving

Steering wheel turningSteering column intermediate
shaft installation condition
STC-32Steering wheel turning force
(Mechanical malfunction)