belt NISSAN VERSA 2006 Workshop Service Manual Online

LAN-1
LAN SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION LAN
A
B
LAN
Revision: June 20062007 Versa
CAN FUNDAMENTAL
PRECAUTIONS .......................................................... 3
Precautions When Using CONSULT-II ..................... 3
Precautions for Trouble Diagnosis ........................... 3
Precautions for Harness Repair ............................... 3
SYSTEM DESCRIPTION ............................................ 4
CAN Communication System ................................... 4
SYSTEM DIAGRAM .............................................. 4
CAN COMMUNICATION CONTROL CIRCUIT ..... 5
Diag on CAN ............................................................ 6
DESCRIPTION ...................................................... 6
SYSTEM DIAGRAM .............................................. 6
TROUBLE DIAGNOSIS .............................................. 7
Condition of Error Detection ..................................... 7
CAN COMMUNICATION SYSTEM ERROR ......... 7
WHEN INDICATED “U1000” OR “U1001” IS INDI-
CATED EVEN THOUGH CAN COMMUNICA-
TION SYSTEM IS NORMAL ................................. 7
Symptom When Error Occurs in CAN Communi-
cation System ........................................................... 8
ERROR EXAMPLE ............................................... 8
Self-Diagnosis ........................................................ 12
CAN Diagnostic Support Monitor ........................... 13
MONITOR ITEM (CONSULT-II) .......................... 13
MONITOR ITEM (ON-BOARD DIAGNOSIS) ...... 14
TROUBLE DIAGNOSES WORK FLOW .................. 15
Information Needed for Trouble Diagnosis ............. 15
How to Use CAN Communication Signal Chart ..... 15
Trouble Diagnosis Flow Chart ................................ 16
Trouble Diagnosis Procedure ................................. 17
INTERVIEW WITH CUSTOMER ......................... 17
INSPECTION OF VEHICLE CONDITION ........... 18
CHECK OF CAN SYSTEM TYPE (HOW TO USE
CAN SYSTEM TYPE SPECIFICATION CHART) ... 19
CREATE INTERVIEW SHEET ............................ 21
CREATE DATA SHEET ....................................... 22
CREATE DIAGNOSIS SHEET ............................ 24
DETECT THE ROOT CAUSE ............................. 25
CAN
INDEX FOR DTC ....................................................... 40
DTC No. Index ........................................................ 40
HOW TO USE THIS SECTION ................................. 41
Caution ................................................................... 41
Abbreviation List ..................................................... 41
PRECAUTIONS ........................................................ 42
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................. 42
Precautions When Using CONSULT-II ................... 42
Precautions for Trouble Diagnosis ......................... 42
Precautions for Harness Repair ............................. 42
TROUBLE DIAGNOSIS ............................................ 44
CAN Diagnostic Support Monitor ............................ 44
MONITOR ITEM LIST (CONSULT-II) .................. 44
CAN System Specification Chart ............................ 47
VEHICLE EQUIPMENT IDENTIFICATION
INFORMATION .................................................... 47
CAN Communication Signal Chart ......................... 48
TYPE 1/TYPE 2/TYPE 3/TYPE 4 ........................ 48
TYPE 5/TYPE 6 ................................................... 49
TYPE 7/TYPE 8/TYPE 9/TYPE 10 ...................... 50
Schematic ............................................................... 53
Wiring Diagram — CAN — ..................................... 54
Interview Sheet ....................................................... 56
Data Sheet .............................................................. 57
CONSULT-II DATA ATTACHMENT SHEET ........ 57
CAN System (Type 1) ............................................. 60
DIAGNOSIS SHEET ........................................... 60
CAN System (Type 2) ............................................. 61
DIAGNOSIS SHEET ........................................... 61
CAN System (Type 3) ............................................. 62
DIAGNOSIS SHEET ........................................... 62
CAN System (Type 4) ............................................. 63
DIAGNOSIS SHEET ........................................... 63
CAN System (Type 5) ............................................. 64
DIAGNOSIS SHEET ........................................... 64
CAN System (Type 6) ............................................. 65
DIAGNOSIS SHEET ........................................... 65

LAN-42
[CAN]
PRECAUTIONS
Revision: June 20062007 Versa
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
UKS005VK
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WAR NIN G:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions When Using CONSULT-IIUKS005YD
Use CONSULT-II CONVERTER when connecting CONSULT-II to data link connector.
CAUTION:
CAN communication does not function properly if CONSULT-II is used without connecting CONSULT-II
CONVERTER.
Precautions for Trouble DiagnosisUKS005YE
CAUTION:

Never apply 7.0 V or more to the measurement terminal.

Use a tester with open terminal voltage of 7.0 V or less.

Turn the ignition switch OFF and disconnect the battery cable from the negative terminal when
checking the harness.
Precautions for Harness RepairUKS005YF

Solder the repaired area and wrap tape around the soldered
area.
NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).
SKIB8766E

LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION LT
A
B
LT
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 4
HEADLAMP (FOR USA) ............................................ 5
Component Parts and Harness Connector Location ..... 5
System Description .................................................. 5
OUTLINE ............................................................... 5
HEADLAMP OPERATION .................................... 6
COMBINATION SWITCH READING FUNCTION ..... 6
EXTERIOR LAMP BATTERY SAVER CONTROL ..... 6
CAN COMMUNICATION SYSTEM DESCRIP-
TION ......................................................................... 6
Schematic ................................................................ 7
Wiring Diagram ........................................................ 8
Terminals and Reference Values for BCM ............. 12
Terminals and Reference Values for IPDM E/R ..... 12
How to Perform Trouble Diagnoses ....................... 12
Preliminary Check .................................................. 12
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM .................................................. 12
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR IPDM E/R .......................................... 12
CONSULT-II Function (BCM) ................................. 12
CONSULT-II START PROCEDURE .................... 12
WORK SUPPORT ............................................... 12
DATA MONITOR ................................................. 12
ACTIVE TEST ..................................................... 13
SELF-DIAGNOSTIC RESULTS .......................... 13
CONSULT-II Function (IPDM E/R) ......................... 13
CONSULT-II START PROCEDURE .................... 13
DATA MONITOR ................................................. 14
ACTIVE TEST ..................................................... 14
Headlamp High Beam Does Not Illuminate (Both
Sides) ..................................................................... 14
Headlamp High Beam Does Not Illuminate (One
Side) ....................................................................... 17
High Beam Indicator Lamp Does Not Illuminate .... 18
Headlamp Low Beam Does Not Illuminate (Both
Sides) ..................................................................... 18Headlamp Low Beam Does Not Illuminate (One
Side) ....................................................................... 21
Headlamps Do Not Turn OFF ................................. 22
Aiming Adjustment .................................................. 23
PREPARATION BEFORE ADJUSTING .............. 23
LOW BEAM AND HIGH BEAM ........................... 23
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 24
Bulb Replacement .................................................. 25
HEADLAMP (HIGH/LOW) ................................... 25
PARKING (CLEARANCE) LAMP ........................ 25
FRONT TURN SIGNAL LAMP ............................ 25
Removal and Installation ........................................ 25
REMOVAL ........................................................... 25
INSTALLATION ................................................... 25
Disassembly and Assembly .................................... 26
DISASSEMBLY ................................................... 26
ASSEMBLY ......................................................... 26
HEADLAMP (FOR CANADA) - DAYTIME LIGHT
SYSTEM - .................................................................. 27
Component Parts and Harness Connector Location ... 27
System Description ................................................. 27
OUTLINE ............................................................. 27
HEADLAMP OPERATION ................................... 28
COMBINATION SWITCH READING FUNCTION ... 29
EXTERIOR LAMP BATTERY SAVER CONTROL ... 29
CAN Communication System Description .............. 29
Schematic ............................................................... 30
Wiring Diagram — DTRL — ................................... 31
Terminals and Reference Values for BCM .............. 35
Terminals and Reference Values for IPDM E/R ...... 35
How to Perform Trouble Diagnoses ....................... 35
Preliminary Check .................................................. 35
CHECK BCM CONFIGURATION ........................ 35
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM .................................................. 35
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR IPDM E/R .......................................... 35
CONSULT-II Function (BCM) ................................. 35
CONSULT-II Function (IPDM E/R) ......................... 35

LT-4
PRECAUTIONS
Revision: June 20062007 Versa
PRECAUTIONS PFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EKS00IM8
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WAR NIN G:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

LU-8Revision: June 2006
OIL FILTER
2007 Versa
OIL FILTERPFP:15208
Removal and InstallationEBS00T73
REMOVAL
1. Remove oil filter using Tool (A).

⇐ Front
CAUTION:

Oil filter is provided with relief valve. Use Genuine NIS-
SAN Oil Filter or equivalent.

Be careful not to get burned when engine and engine oil
may be hot.

When removing, prepare a shop cloth to absorb any
engine oil leakage or spillage.

Do not allow engine oil to adhere to drive belt.

Completely wipe off any engine oil that adheres to engine and vehicle.
INSTALLATION
1. Remove foreign materials adhering to the oil filter installation surface.
2. Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
3. Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn. Or tighten to specification.
INSPECTION AFTER INSTALLATION
1. Check the engine oil level. Refer to LU-5, "ENGINE OIL" .
2. Start engine, and make sure there is no leaks of engine oil.
3. Stop engine and wait for 10 minutes.
4. Check the engine oil level and adjust engine oil. Refer to LU-5, "
ENGINE OIL" . Tool number : KV10115801 (J-38956)
PBIC3818E
SM A01 0
Oil filter: : 17.7 N·m (1.8 kg-m, 13 ft-lb)
SM A22 9B

MA-1
MAINTENANCE
L MAINTENANCE
CONTENTS
C
D
E
F
G
H
I
J
K
M
SECTION MA
A
B
MA
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
GENERAL MAINTENANCE ....................................... 5
Explanation of General Maintenance ....................... 5
General Maintenance ............................................... 5
PERIODIC MAINTENANCE ....................................... 7
Introduction of Periodic Maintenance ....................... 7
Schedule 1 ............................................................... 7
EMISSION CONTROL SYSTEM MAINTE-
NANCE .................................................................. 7
CHASSIS AND BODY MAINTENANCE ............... 8
Schedule 2 ............................................................... 9
EMISSION CONTROL SYSTEM MAINTE-
NANCE .................................................................. 9
CHASSIS AND BODY MAINTENANCE ............. 10
RECOMMENDED FLUIDS AND LUBRICANTS .......11
Fluids and Lubricants ..............................................11
SAE Viscosity Number ........................................... 12
Anti-freeze Coolant Mixture Ratio .......................... 12
ENGINE MAINTENANCE ......................................... 13
Drive Belts .............................................................. 13
Checking Drive Belts .............................................. 13
Tension Adjustment ................................................ 13
Changing Engine Coolant ...................................... 13
DRAINING ENGINE COOLANT ......................... 13
REFILLING ENGINE COOLANT ........................ 14
FLUSHING COOLING SYSTEM ......................... 15
Inspection ............................................................... 15
LEVEL CHECK ................................................... 15
CHECKING COOLING SYSTEM FOR LEAKS ... 15
Checking Fuel Lines ............................................... 15
Changing Air Cleaner Filter .................................... 16
REMOVAL ........................................................... 16
INSPECTION AFTER REMOVAL ....................... 16
INSTALLATION ................................................... 16Changing Engine Oil ............................................... 16
Engine Oil Filter ...................................................... 17
REMOVAL ........................................................... 17
INSTALLATION ................................................... 17
INSPECTION AFTER INSTALLATION ................ 18
Changing Spark Plugs ............................................ 18
............................................................................ 18
INSPECTION AFTER REMOVAL ....................... 18
INSTALLATION ................................................... 19
Checking EVAP Vapor Lines .................................. 19
CHASSIS AND BODY MAINTENANCE ................... 20
Changing In-cabin Microfilter .................................. 20
Checking Exhaust System ...................................... 20
Checking CVT Fluid ................................................ 20
FLUID LEVEL CHECK ........................................ 20
FLUID CONDITION CHECK ............................... 21
Changing CVT Fluid ............................................... 21
Checking Clutch Fluid Level and Leaks ................. 22
Checking Clutch System ........................................ 22
Checking M/T Oil .................................................... 22
OIL LEAKAGE AND OIL LEVEL ......................... 22
Changing M/T Oil .................................................... 22
DRAINING ........................................................... 22
FILLING ............................................................... 22
Checking A/T Fluid ................................................. 22
Changing A/T Fluid ................................................. 23
Balancing Wheels ................................................... 24
Rotation .................................................................. 24
Checking Brake Fluid Level and Leaks .................. 24
Checking Brake Lines and Cables ......................... 24
Changing Brake Fluid ............................................. 25
Checking Disc Brake .............................................. 25
ROTOR ................................................................ 25
CALIPER ............................................................. 25
PAD ..................................................................... 25
WHEEL CYLINDER ............................................ 26
LINING ................................................................ 26
Axle and Suspension Parts .................................... 26
Drive Shaft .............................................................. 27

MA-2Revision: June 20062007 Versa Lubricating Locks, Hinges and Hood Latch ............ 27
Checking Seat Belts, Buckles, Retractors, Anchors and Adjusters ..........................................................27

PRECAUTIONS
MA-3
C
D
E
F
G
H
I
J
K
MA
B
MA
Revision: June 20062007 Versa
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
ELS001YA
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WA RN ING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

GENERAL MAINTENANCE
MA-5
C
D
E
F
G
H
I
J
K
MA
B
MA
Revision: June 20062007 Versa
GENERAL MAINTENANCEPFP:00000
Explanation of General MaintenanceELS001YB
General MaintenanceELS001YC
General maintenance includes those items which should be checked during the normal day-to-day operation
of the vehicle. They are essential if the vehicle is to continue operating properly. The owners can perform
checks and inspections themselves or they can have their NISSAN dealers do them.
OUTSIDE THE VEHICLE
The maintenance items listed here should be performed from time to time, unless otherwise specified.
INSIDE THE VEHICLE
The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the
vehicle, etc.ItemReference page
TiresCheck the pressure including the spare, at least once a month and always prior
to a long distance trip. Adjust to the specified pressure if necessary. Check care-
fully for damage, cuts or excessive wear.WT-29, "
Tire"
Wheel nutsWhen checking the tires, make sure no nuts are missing, and check for any
loose nuts. Tighten if necessary.WT-6, "Rotation"
WindshieldClean the windshield on a regular basis. Check the windshield at least every six
months for cracks or other damage. Repair as necessary.—
Tire rotationTires should be rotated every 12,000 km (7,500 miles).WT-6, "
Rotation"
Wheel alignment and
balanceIf the vehicle pulls to either side while driving on a straight and level road, or if
you detect uneven or abnormal tire wear, there may be a need for wheel align-
ment. If the steering wheel or seat vibrates at normal highway speeds, wheel
balancing may be needed.FSU-6, "Wheel Align-
ment Inspection" and
WT-6, "
Balancing
Wheels"
Windshield wiper
bladesCheck for cracks or wear if they do not wipe properly. —
Doors and engine
hoodCheck that all doors and the engine hood operate smoothly as well as the trunk
lid and back hatch. Also make sure that all latches lock securely. Lubricate if
necessary. Make sure that the secondary latch keeps the hood from opening
when the primary latch is released.
When driving in areas using road salt or other corrosive materials, check lubri-
cation frequently.MA-27, "
Lubricating
Locks, Hinges and Hood
Latch"
LampsMake sure that the headlamps, stop lamps, tail lamps, turn signal lamps, and
other lamps are all operating properly and installed securely. Also check head-
lamp aim. Clean the headlamps on a regular basis.—
ItemReference page
Warning lamps and
buzzers/chimesMake sure that all warning lamps and buzzers/chimes are operating properly. —
Windshield wiper and
washerCheck that the wipers and washer operate properly and that the wipers do not
streak.—
Windshield defrosterCheck that the air comes out of the defroster outlets properly and in sufficient
quantity when operating the heater or air conditioning.—
Steering wheelCheck that it has the specified play. Be sure to check for changes in the steering
condition, such as excessive play, hard steering or strange noises.
Free play: Less than 35 mm (1.38 in)—
SeatsCheck seat position controls such as seat adjusters, seat back recliner, etc. to
make sure they operate smoothly and that all latches lock securely in every
position. Check that the head restraints move up and down smoothly and that
the locks (if equipped) hold securely in all latched positions. Check that the
latches lock securely for folding-down rear seat backs.—
Seat belts
Check that all parts of the seat belt system (e.g. buckles, anchors, adjusters and
retractors) operate properly and smoothly and are installed securely. Check the
belt webbing for cuts, fraying, wear or damage.MA-27, "
Checking Seat
Belts, Buckles, Retrac-
tors, Anchors and
Adjusters"

MA-6
GENERAL MAINTENANCE
Revision: June 20062007 Versa
UNDER THE HOOD AND VEHICLE
The maintenance items listed here should be checked periodically (e.g. each time you check the engine oil or refuel).Accelerator pedalCheck the pedal for smooth operation and make sure the pedal does not catch
or require uneven effort. Keep the floor mats away from the pedal.—
Clutch pedalMake sure the pedal operates smoothly and check that it has the proper free
play.MA-22
BrakesCheck that the brake does not pull the vehicle to one side when applied. —
Brake pedal and
boosterCheck the pedal for smooth operation and make sure it has the proper distance
under it when depressed fully. Check the brake booster function. Be sure to
keep floor mats away from the pedal.BR-6, "
Inspection and
Adjustment" and BR-19,
"On-board Inspection"
Parking brakeCheck that the lever has the proper travel and make sure that the vehicle is held
securely on a fairly steep hill when only the parking brake is applied.PB-4, "INSPECTION"
Automatic transaxle
“Park” mechanismCheck that the lock release button on the selector lever operates properly and
smoothly. On a fairly steep hill check that the vehicle is held securely with the
selector lever in the “P” position without applying any brakes.—
CVT P (Park) position
mechanismOn a fairly steep hill check that the vehicle is held securely with the selector
lever in the “P” position without applying any brakes.— ItemReference page
ItemReference page
Windshield
washer fluidCheck that there is adequate fluid in the tank. —
Engine coolant
levelCheck the coolant level when the engine is cold.CO-8, "
LEVEL CHECK"
A/C condenser,
radiator and
hosesCheck the front of the condenser and radiator and clean off any dirt, insects,
leaves, etc., that may have accumulated. Make sure the radiator hoses have no
cracks, deformation, deterioration or loose connections.—
Brake and clutch
fluid levelsMake sure that the brake and clutch fluid levels are between the “MAX” and “MIN”
lines on the reservoirs.BR-9, "
CHECKING BRAKE
FLUID LEVEL" and MA-22,
"Checking Clutch Fluid
Level and Leaks"
BatteryCheck the fluid level in each cell. It should be between the “MAX” and “MIN” lines.
Vehicles operated in high temperatures or under severe conditions require fre-
quent checks of the battery fluid level.—
Engine drive beltsMake sure that no belt is frayed, worn, cracked or oily.MA-13
Engine oil levelCheck the level on the dipstick after parking the vehicle on a level spot and turning
off the engine.LU-5, "ENGINE OIL
LEVEL"
Automatic tran-
saxle fluid levelCheck the level on the dipstick after putting the selector lever in “P” with the
engine idling.MA-20 and MA-22
Exhaust systemMake sure there are no loose supports, cracks or holes. If the sound of the
exhaust seems unusual or there is a smell of exhaust fumes, immediately locate
the trouble and correct it.MA-20
UnderbodyThe underbody is frequently exposed to corrosive substances such as those used
on icy roads or to control dust. It is very important to remove these substances,
otherwise rust will form on the floor pan, frame, fuel lines and around the exhaust
system. At the end of winter, the underbody should be thoroughly flushed with
plain water, being careful to clean those areas where mud and dirt can easily
accumulate.—
Fluid leaksCheck under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has
been parked for a while. Water dripping from the air conditioner after use is nor-
mal. If you should notice any leaks or gasoline fumes are evident, check for the
cause and correct it immediately.—