EM-133 NISSAN X-TRAIL 2001 Service Repair Manual

OIL PAN AND OIL STRAINER
EM-133
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM
OIL PAN AND OIL STRAINERP F P : 1111 0
Removal and InstallationEBS00LRK
REMOVAL
WARNING:
To avoid the danger of being scalded, never drain the engine oil when the engine is hot.
1. Remove engine undercover at both side.
2. Drain engine oil. Refer to LU-19, "
Changing Engine Oil" .
3. Remove lower oil pan bolts, Loosen bolts in the reverse order of
that shown in the figure.
PBIC1140E
1. Rear plate cover 2. Oil pan upper 3. Oil strainer
4. Drain plug 5. Oil pan lower 6 Crankshaft position sensor (TDC)
SBIA0161E

EM-174
[YD22DDTi]
PRIMARY TIMING CHAIN
REMOVAL
1. Remove engine coolant reservoir tank.
2. Remove charge air cooler and bracket. Refer to EM-122, "
Removal and Installation" .
3. Remove air cleaner and air duct. Refer to EM-120, "
Removal and Installation" .
4. Remove rocker cover. Refer to EM-156, "
Removal and Installation" .
5. Remove RH engine mount insulator and bracket. Refer to EM-193, "
Removal and Installation" .
6. Pull power steering reservoir tank out of brackets to move power steering piping.
CAUTION:
To avoid removing power steering reservoir tank out of brackets move it with power steering pip-
ing aside.
7. Remove oil pan. Refer to EM-133, "
Removal and Installation" .
8. Remove oil filter bracket. Refer to LU-22, "
OIL FILTER BRACKET" .
9. Remove injection tube and fuel injector. Refer to EM-144, "
Removal and Installation" .
10. Remove secondary timing chain and associated parts. Refer to EM-167, "
Removal and Installation" .
11. When removing rear chain case, remove camshaft sprockets. Refer to EM-158, "
Removal and Installa-
tion" .
12. Remove crankshaft pulley.
a. Hold crankshaft pulley with the pulley holder (SST).
b. Loosen crankshaft pulley fixing bolt and pull out the bolt approx-
imately 10 mm (0.39 in).
c. Using pulley puller (SST), remove crankshaft pulley.
●Use two M6 bolts with approx. 60 mm (2.36 in) shank length
for securing crankshaft pulley.
13. Remove oil pump housing.
●Loosen bolts in the reverse order of that shown in the figure
and remove them.
●Use seal cutter (SST) etc. for removal.
14. Remove front oil seal from oil pump housing.
●Punch out the seal off from the back surface of the oil pump
using a flat-bladed screwdriver.
●Be careful not to damage the oil pump housing.
7. Chain guide 8. Spacer 9. Front chain case
10. Crankshaft pulley 11. Front oil seal 12. Oil pump housing
13. Primary timing chain 14. Oil pump drive spacer 15. Crankshaft sprocket
16. Secondary timing chain 17. Rear chain case 18. Power steering pump
JEM131G
JEM132G
JEM133G

CYLINDER BLOCK
EM-199
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM
e. Hoist engine and install it to the engine stand.
NOTE:
It is possible to set engine sub-attachment and engine attach-
ment to engine stand at first, then install engine later.
●Commercial engine stand can be used.
NOTE:
The figure shows an example of general-purpose engine
stand that can hold mating surface of transmission with drive
plate and rear plate removed.
5. Drain engine oil and engine coolant from inside engine.
6. Remove the following parts and related parts. (Only major parts are listed.)
●Intake manifold (Refer to EM-123, "Removal and Installation" .)
●Exhaust manifold and Turbocharger (Refer to EM-127, "Removal and Installation" .)
●Rocker cover (Refer to EM-156, "Removal and Installation" .)
●Injection tube and fuel injector (Refer to EM-144, "Removal and Installation" .)
●Oil pan and oil strainer (Refer to EM-133, "Removal and Installation" .)
●Water pump (Refer to CO-39, "WATER PUMP" .)
●Thermostat and water piping (Refer to CO-41, "THERMOSTAT AND WATER PIPING" .)
●Vacuum pump and vacuum pipe (Refer to EM-139, "Removal and Installation" .)
●Secondary timing chain (Refer to EM-167, "Removal and Installation" .)
●Primary timing chain (Refer to EM-172, "Removal and Installation" .)
●Fuel supply pump (Refer to EM-147, "Removal and Installation" .)
●Camshaft (Refer to EM-158, "Removal and Installation" .)
●Cylinder head (Refer to EM-183, "Removal and Installation" .)
●Oil cooler (Refer to LU-25, "OIL COOLER" .)
●Accessory, accessory bracket and mount brackets
7. Remove fuel supply pump bracket.
8. Remove rear oil seal retainer.
JEM193G
PBIC0085E

IDX-7
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Molding - See Exterior ................... EI-14,EI-16,EI-17
Mud guard - See Exterior .................................... EI-16
MULTI - Wiring diagram ..................................... BL-57
Multiport fuel injection (MFI) system ... EC-33,EC-443,
EC-765
,EC-1129
Multiport fuel injection precautions ....................... GI-6
Multi-remote control system ............................... BL-55
N
NATS - Wiring diagram ....................................... BL-83
NATS (Nissan anti-theft system) ........................ BL-80
NATS (Nissan anti-theft system) precautions ....... GI-3
NVH troubleshooting (BR) ......................... BR-5,PB-2
NVH troubleshooting (CL) ................................... CL-4
NVH troubleshooting (EM)(QR20DE•QR25DE) EM-10
NVH troubleshooting (EM)(YD22DDTi) ........... EM-116
NVH troubleshooting (M/T) .................................. MT-7
NVH troubleshooting (PR) ................................. FAX-6
NVH troubleshooting (RA) ................................. RAX-5
NVH troubleshooting (RAX) ............................... RAX-5
NVH troubleshooting (RSU) ............................. RSU-4
NVH troubleshooting (Transfer) ............................ TF-7
O
Oil cooler (engine)(QR20DE•QR25DE) ............. LU-13
Oil cooler (engine)(YD22DDTi) .......................... LU-25
Oil filter(QR20DE•QR25DE) ................................ LU-9
Oil filter(YD22DDTi) ........................................... LU-20
Oil pan (engine)(QR20DE•QR25DE) ................. EM-26
Oil pan (engine)(YD22DDTi) ........................... EM-133
Oil pressure (engine)(QR20DE•QR25DE) ........... LU-7
Oil pressure (engine)(YD22DDTi) ..................... LU-18
Oil pump (engine)(QR20DE•QR25DE) .............. LU-10
Oil pump (engine)(YD22DDTi) .......................... LU-23
Oil pump regulator valve (engine)(QR20DE•QR25DE)
LU-11
Oil pump regulator valve (engine)(YD22DDTi) .. LU-24
Oil seal replacement (engine)(QR20DE•QR25DE) ......
EM-37
,EM-59,EM-73
On board diagnostic system . EC-44,EC-454,EC-777,
EC-1141
Operating cylinder (clutch) ................................. CL-11
Out side mirror .................................................. GW-49
Overdrive control switch ..................... AT-246,AT-349
Overheat ........................................................ EC-1508
Oversize piston(QR20DE•QR25DE) ................. EM-93
Oversize piston(YD22DDTi) ............................ EM-214
P
Park/Neutral position switch ............. EC-345
,EC-705,
EC-1064
,EC-1353,EC-1562
Park/neutral position switch (A/T) .................... AT-110
Park/neutral position switch (M/T) ..................... MT-12
PCV (positive crankcase ventilation) EC-428,EC-749,
EC-1115
,EC-1389
PGC/V - Wiring diagram .................... EC-246,EC-974
PHASE - Wiring diagram ... EC-235,EC-559,EC-964,
EC-1248
Pilot bushing replacement - See Pilot
converter(QR20DE•QR25DE) .......................... EM-73
Piston assembly(QR20DE•QR25DE) ............... EM-93
Piston pin inspection(QR20DE•QR25DE) ........ EM-89
Piston pin inspection(YD22DDTi) ................... EM-206
Piston ring inspection(QR20DE•QR25DE) ....... EM-90
Piston ring inspection(YD22DDTi) .................. EM-211
Piston to bore clearance(QR20DE•QR25DE) ... EM-93
Piston to bore clearance(YD22DDTi) ............. EM-214
PNP/SW - Wiring diagram EC-347,EC-1066,EC-1563
PNPSW1 - Wiring diagram .............. EC-706,EC-1354
POS - Wiring diagram ........ EC-229,EC-553,EC-958,
EC-1242
POWER - Wiring diagram .................................... PG-3
Power antenna ................................................... AV-16
Power door lock ................................................. BL-11
Power socket ................................................... WW-27
Power steering fluid level ........................ PS-5,MA-40
Power steering gear ........................................... PS-12
Power steering oil pressure switch ................ EC-1568
Power steering oil pump .................................... PS-24
Power steering pressure (PSP) sensor .......... EC-255,
EC-568
,EC-983,EC-1257
Power supply routing ........................................... PG-2
Power window ................................................... GW-23
Precations for Leak detection dye ................... ATC-12
Precautions (General) ........................................... GI-4
Pressure plate - See Clutch cover ..................... CL-15
PRGVLV - Wirng diagram ................ EC-694,EC-1342
Propeller shaft ...................................................... PR-2
Propeller shaft on vehicle service ........................ PR-2
PS/SEN - Wiring diagram .. EC-257,EC-570,EC-985,
EC-1259
PST/SW - Wiring diagram .............................. EC-1569
Q
Quick-glow system ......................................... EC-1544
R
R/FOG - Wiring diagram ..................................... LT-37
Radiator fan - See Cooling fan(QR20DE•QR25DE) .....
CO-12
Radiator fan - See Cooling fan(YD22DDTi) ...... CO-33
Radiator(QR20DE•QR25DE) ................ CO-11,CO-14
Radiator(YD22DDTi) ............................. CO-32,CO-35
Radio - See Audio ................................................ AV-3
Rear air spoiler ................................................... EI-21
Rear bumper ......................................................... EI-9
Rear cover packing replacement diff. ............. RFD-10
Rear disc brake .................................................. BR-26
Rear door ............................................................. BL-8
Rear fog lamp ..................................................... LT-37
Rear panel finisher .............................................. EI-22
Rear seat ........................................................... SE-11
Rear seat belt ...................................................... SB-4