light NISSAN X-TRAIL 2005 Service Owner's Manual

CYLINDER BLOCK
EM-253
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

MAIN BEARING OIL CLEARANCE
Method by Measurement

Install main bearings to cylinder block and bearing cap, and
tighten the bolts to the specified torque. Refer to EM-235,
"ASSEMBLY" . Then, measure the inner diameter of main bear-
ings.
(Bearing clearance) = (Bearing inner diameter) − (Crankshaft
main journal diameter)

If out of the standard, check main bearing housing inner diame-
ter and crankshaft main journal diameter, and select appropriate
main bearing to adjust clearance to specifications. Refer to EM-
244, "HOW TO SELECT MAIN BEARING" .
Method of Using Plastigage

Remove contamination such as engine oil and dust completely
from crankshaft main journal and each bearing surface.

Cut plastigage slightly shorter than bearing width. Place it in
crankshaft turning direction, avoiding oil holes.

Install main bearings and bearing cap and tighten to the speci-
fied torque. Refer to EM-235, "
ASSEMBLY" for the tightening
procedure.
CAUTION:
Do not rotate crankshaft.

Remove main bearings and bearing caps, and measure plasti-
gage width using scale on plastigage bag.
NOTE:
If out of specification, take same action mentioned in “Method by Measurement”.
CRUSH HEIGHT OF MAIN BEARING

When bearing cap is removed after being tightened to the speci-
fied torque with main bearings installed, the tip end of bearing
must protrude. Refer to EM-235, "
ASSEMBLY" .

If out of the standard, replace main bearings.
CRUSH HEIGHT OF CONNECTING ROD BEARING

When connecting rod bearing cap is removed after being tight-
ened to the specified torque with connecting rod bearings
installed, the tip end of bearing must protrude. Refer to EM-235,
"ASSEMBLY" .

If out of the standard, replace connecting rod bearings.Standard : 0.039 - 0.066 mm (0.0015 - 0.0026 in)
PBIC1644E
EM142
Standard : There must be crush height.
SEM502G
Standard : There must be crush height.
PBIC1646E

PRECAUTIONS
LU-3
[QR]
C
D
E
F
G
H
I
J
K
L
MA
LU

[QR]PRECAUTIONSPFP:00001
Precautions for Liquid GasketEBS011UN
LIQUID GASKET APPLICATION PROCEDURE
1. Remove old liquid gasket adhering to the liquid gasket application surface and the mating surface.

Remove liquid gasket completely from the liquid gasket application surface, mounting bolts, and bolt
holes.
2. Wipe the liquid gasket application surface and the mating surface with white gasoline (lighting and heating
use) to remove adhering moisture, grease and foreign materials.
3. Attach liquid gasket tube to the tube presser (special service
tool).
Use Genuine Liquid Gasket or equivalent.

Within five minutes of liquid gasket application, install the mat-
ing component.

If liquid gasket protrudes, wipe it off immediately.

Do not retighten mounting bolts or nuts after the installation.

Wait 30 minutes or more after installation before refilling
engine oil and engine coolant.
PBIC2160E

PRECAUTIONS
LU-17
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
LU

[YD22DDTi]PRECAUTIONSPFP:00001
Precautions for Liquid GasketEBS011SZ
LIQUID GASKET APPLICATION PROCEDURE
1. Remove the old liquid gasket adhering to the gasket application surface and the mating surface.

Remove the liquid gasket completely from the gasket application surface, mounting bolts, and bolt holes.
2. Wipe the liquid gasket application surface and the mating surface with white gasoline (lighting and heating
use) to remove adhering moisture, grease and foreign materials.
3. Attach liquid gasket tube to the tube presser (special service
tool).
Use Genuine Liquid Gasket or equivalent.

Within five minutes of gasket application, install the mating com-
ponent.

If the liquid gasket protrudes, wipe it off immediately.

Do not retighten mounting bolts and nuts after the installation.

Wait 30 minutes or more after installation before filling the
engine with engine oil and engine coolant.
PBIC2160E

PRECAUTIONS
CO-3
[QR]
C
D
E
F
G
H
I
J
K
L
MA
CO

[QR]PRECAUTIONSPFP:00001
Precautions for Liquid GasketEBS00MRX
LIQUID GASKET APPLICATION PROCEDURE
1. Remove old liquid gasket adhering to the liquid gasket application surface and the mating surface.

Remove liquid gasket completely from the liquid gasket application surface, mounting bolts, and bolt
holes.
2. Wipe the liquid gasket application surface and the mating surface with white gasoline (lighting and heating
use) to remove adhering moisture, grease and foreign materials.
3. Attach liquid gasket tube to the tube presser (special service
tool).
Use Genuine Liquid Gasket or equivalent.

Within five minutes of liquid gasket application, install the mat-
ing component.

If liquid gasket protrudes, wipe it off immediately.

Do not retighten mounting bolts or nuts after the installation.

Wait 30 minutes or more after installation before refilling
engine oil and engine coolant.
PBIC2160E

CO-26
[YD22DDTi]
PRECAUTIONS

[YD22DDTi]PRECAUTIONSPFP:00001
Precautions For Liquid GasketEBS01276
LIQUID GASKET APPLICATION PROCEDURE
1. Remove old liquid gasket adhering to the liquid gasket application surface and the mating surface.

Remove liquid gasket completely from the liquid gasket application surface, mounting bolts, and bolt
holes.
2. Wipe the liquid gasket application surface and the mating surface with white gasoline (lighting and heating
use) to remove adhering moisture, grease and foreign materials.
3. Attach liquid gasket tube to the tube presser (special service
tool).
Use Genuine Liquid Gasket or equivalent.

Within five minutes of liquid gasket application, install the mat-
ing component.

If liquid gasket protrudes, wipe it off immediately.

Do not retighten mounting bolts or nuts after the installation.

After 30 minutes or more have passed from the installation, fill
engine oil and engine coolant.
PBIC2160E

INDEX FOR DTC
EC-19
[QR (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC

[QR (WITH EURO-OBD)]INDEX FOR DTCPFP:00024
Alphabetical IndexEBS010KY
Check if the vehicle is a model with Euro-OBD (E-OBD) system or not by the Type approval number on the
identification plate. Refer to GI-46, "
IDENTIFICATION PLATE" .
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to EC-133, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
Items
(CONSULT-II screen terms)DTC*
1
TripMI lighting
upReference page
CONSULT-II
GST*
2ECM*3
A/T 1ST GR FNCTN P0731 0731 2×AT-125
A/T 2ND GR FNCTN P0732 0732 2×AT-130
A/T 3RD GR FNCTN P0733 0733 2×AT-135
A/T 4TH GR FNCTN P0734 0734 2×AT-140
APP SEN 1/CIRC P2122 2122 1×EC-409
APP SEN 1/CIRC P2123 2123 1×EC-409
APP SEN 2/CIRC P2127 2127 1×EC-416
APP SEN 2/CIRC P2128 2128 1×EC-416
APP SENSOR P2138 2138 1×EC-432
ASCD BRAKE SW*8P1572 1572 1 —EC-387
ASCD SW *8P1564 1564 1 —EC-377
ASCD VHL SPD SEN*8P1574 1574 1 —EC-396
ATF TEMP SEN/CIRC P0710 0710 2×AT-106
BRAKE SW/CIRCUIT P1805 1805 2 —EC-405
CAN COMM CIRCUIT U1000
1000*51 (A/T)
2 (M/T)× (A/T)
— (M/T)EC-133
CAN COMM CIRCUIT U1001
1001*52—EC-133
CKP SEN/CIRCUIT P0335 0335 2×EC-250
CMP SEN/CIRC-B1 P0340 0340 2×EC-257
CTP LEARNING P1225 1225 2 —EC-368
CTP LEARNING P1226 1226 2 —EC-370
CYL 1 MISFIRE P0301 0301 2×EC-239
CYL 2 MISFIRE P0302 0302 2×EC-239
CYL 3 MISFIRE P0303 0303 2×EC-239
CYL 4 MISFIRE P0304 0304 2×EC-239
ECM P0605 0605 1 or 2× or —EC-283
ECM BACK UP/CIRCUIT P1065 1065 2×EC-286
ECT SEN/CIRC P0117 0117 1×EC-165
ECT SEN/CIRC P0118 0118 1×EC-165
ENG OVER TEMP P1217 1217 1×EC-352
ENGINE SPEED SIG P0725 0725 2×AT- 11 9
ETC ACTR P1121 1121 1×EC-294
ETC FUNCTION/CIRC P1122 1122 1×EC-296
E T C M O T P 11 2 8 11 2 8 1×EC-314
ETC MOT PWR P1124 1124 1×EC-306
ETC MOT PWR P1126 1126 1×EC-306

EC-20
[QR (WITH EURO-OBD)]
INDEX FOR DTC

FUEL SYS-LEAN-B1 P0171 0171 2×EC-219
FUEL SYS-RICH-B1 P0172 0172 2×EC-225
HO2S1 (B1) P0132 0132 2×EC-179
HO2S1 (B1) P0133 0133 2×EC-186
HO2S1 (B1) P0134 0134 2×EC-196
HO2S1 (B1) P1143 1143 2×EC-322
HO2S1 (B1) P1144 1144 2×EC-328
HO2S1 HTR (B1) P0031 0031 2×EC-139
HO2S1 HTR (B1) P0032 0032 2×EC-139
HO2S2 (B1) P0138 0138 2×EC-204
HO2S2 (B1) P0139 0139 2×EC-211
HO2S2 (B1) P1146 1146 2×EC-334
HO2S2 (B1) P1147 1147 2×EC-342
HO2S2 HTR (B1) P0037 0037 2×EC-145
HO2S2 HTR (B1) P0038 0038 2×EC-145
IAT SEN/CIRCUIT P0112 0112 2×EC-159
IAT SEN/CIRCUIT P0113 0113 2×EC-159
INT/V TIM CONT-B1 P0011 0011 2 —EC-136
I N T / V T I M V / C I R - B 1 P 1111 1111 2×EC-290
KNOCK SEN/CIRC-B1 P0327 0327 2 —EC-245
KNOCK SEN/CIRC-B1 P0328 0328 2 —EC-245
L/PRESS SOL/CIRC P0745 0745 2×AT- 1 5 4
MAF SEN/CIRCUIT P0102 0102 1×EC-151
MAF SEN/CIRCUIT P0103 0103 1×EC-151
MULTI CYL MISFIRE P0300 0300 2×EC-239
NATS MALFUNCTION P1610 - P1615 1610 - 1615 2 —BL-108
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.No DTC
Flashing*4—
Flashing*4EC-65
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.P0000 0000———
O/R CLTCH SOL/CIRC P1760 1760 2×AT- 1 7 8
P-N POS SW/CIRCUIT P1706 1706 2×EC-398
PNP SW/CIRC P0705 0705 2×AT- 1 0 0
PURG VOLUME CONT/V P0444 0444 2×EC-269
PW ST P SEN/CIRC P0550 0550 2 —EC-278
SENSOR POWER/CIRC P1229 1229 1×EC-372
SFT SOL A/CIRC P0750 0750 1×AT- 1 6 1
SFT SOL B/CIRC P0755 0755 1×AT- 1 6 7
TCC SOLENOID/CIRC P0740 0740 2×AT- 1 4 8
TCS C/U FUNCTN*6P1211 1211 2 —EC-350
TCS/CIRC*6P1212 1212 2 —EC-351
Items
(CONSULT-II screen terms)DTC*
1
TripMI lighting
upReference page
CONSULT-II
GST*
2ECM*3

INDEX FOR DTC
EC-21
[QR (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC

*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by ISO 15031-5.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: When engine is running
*5: The troubleshooting for this DTC needs CONSULT-II.
*6: For models with ESP system
*7: When the fail-safe operation for both self-diagnoses occur, the MI illuminates.
*8: For QR25DE engine models
DTC No. IndexEBS010KZ
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to EC-133, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
TP SEN 1/CIRC P0222 0222 1×EC-231
TP SEN 1/CIRC P0223 0223 1×EC-231
TP SEN 2/CIRC P0122 0122 1×EC-171
TP SEN 2/CIRC P0123 0123 1×EC-171
TP SENSOR P2135 2135 1×EC-424
TP SEN/CIRC A/T P1705 1705 1×AT-173
TW CATALYST SYS-B1 P0420 0420 2×EC-264
V/SP SEN (A/T OUT) P1720 1720 2 —EC-403
VEH SPD SEN/CIR AT*7P0720 0720 2×AT- 11 2
VEH SPEED SEN/CIRC*7P0500 0500 2×EC-276
Items
(CONSULT-II screen terms)DTC*
1
TripMI lighting
upReference page
CONSULT-II
GST*
2ECM*3
DTC*1
Items
(CONSULT-II screen terms)TripMI lighting
upReference page
CONSULT-II
GST*
2ECM*3
No DTC
Flashing*4NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.—
Flashing*4EC-65
U1000
1000*5CAN COMM CIRCUIT1 (A/T)
2 (M/T)× (A/T)
— (M/T)EC-133
U1001
1001*5CAN COMM CIRCUIT 2 —EC-133
P0000 0000NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.———
P0011 0011 INT/V TIM CONT-B1 2 —EC-136
P0031 0031 HO2S1 HTR (B1) 2×EC-139
P0032 0032 HO2S1 HTR (B1) 2×EC-139
P0037 0037 HO2S2 HTR (B1) 2×EC-145
P0038 0038 HO2S2 HTR (B1) 2×EC-145
P0102 0102 MAF SEN/CIRCUIT 1×EC-151
P0103 0103 MAF SEN/CIRCUIT 1×EC-151
P0112 0112 IAT SEN/CIRCUIT 2×EC-159
P0113 0113 IAT SEN/CIRCUIT 2×EC-159
P0117 0117 ECT SEN/CIRC 1×EC-165
P0118 0118 ECT SEN/CIRC 1×EC-165
P0122 0122 TP SEN 2/CIRC 1×EC-171

EC-22
[QR (WITH EURO-OBD)]
INDEX FOR DTC

P0123 0123 TP SEN 2/CIRC 1×EC-171
P0132 0132 HO2S1 (B1) 2×EC-179
P0133 0133 HO2S1 (B1) 2×EC-186
P0134 0134 HO2S1 (B1) 2×EC-196
P0138 0138 HO2S2 (B1) 2×EC-204
P0139 0139 HO2S2 (B1) 2×EC-211
P0171 0171 FUEL SYS-LEAN-B1 2×EC-219
P0172 0172 FUEL SYS-RICH-B1 2×EC-225
P0222 0222 TP SEN 1/CIRC 1×EC-231
P0223 0223 TP SEN 1/CIRC 1×EC-231
P0300 0300 MULTI CYL MISFIRE 2×EC-239
P0301 0301 CYL 1 MISFIRE 2×EC-239
P0302 0302 CYL 2 MISFIRE 2×EC-239
P0303 0303 CYL 3 MISFIRE 2×EC-239
P0304 0304 CYL 4 MISFIRE 2×EC-239
P0327 0327 KNOCK SEN/CIRC-B1 2 —EC-245
P0328 0328 KNOCK SEN/CIRC-B1 2 —EC-245
P0335 0335 CKP SEN/CIRCUIT 2×EC-250
P0340 0340 CMP SEN/CIRC-B1 2×EC-257
P0420 0420 TW CATALYST SYS-B1 2×EC-264
P0444 0444 PURG VOLUME CONT/V 2×EC-269
P0500 0500
VEH SPEED SEN/CIRC*72×EC-276
P0550 0550 PW ST P SEN/CIRC 2 —EC-278
P0605 0605 ECM 1 or 2× or —EC-283
P0705 0705 PNP SW/CIRC 2×AT-100
P0710 0710 ATF TEMP SEN/CIRC 2×AT-106
P0720 0720
VEH SPD SEN/CIR AT*72×AT- 11 2
P0725 0725 ENGINE SPEED SIG 2×AT- 11 9
P0731 0731 A/T 1ST GR FNCTN 2×AT-125
P0732 0732 A/T 2ND GR FNCTN 2×AT-130
P0733 0733 A/T 3RD GR FNCTN 2×AT-135
P0734 0734 A/T 4TH GR FNCTN 2×AT-140
P0740 0740 TCC SOLENOID/CIRC 2×AT-148
P0745 0745 L/PRESS SOL/CIRC 2×AT-154
P0750 0750 SFT SOL A/CIRC 1×AT-161
P0755 0755 SFT SOL B/CIRC 1×AT-167
P1065 1065 ECM BACK UP/CIRCUIT 2×EC-286
P 1111 1111 I N T / V T I M V / C I R - B 1 2×EC-290
P1121 1121 ETC ACTR 1×EC-294
P1122 1122 ETC FUNCTION/CIRC 1×EC-296
P1124 1124 ETC MOT PWR 1×EC-306
P1126 1126 ETC MOT PWR 1×EC-306
DTC*1
Items
(CONSULT-II screen terms)TripMI lighting
upReference page
CONSULT-II
GST*
2ECM*3

INDEX FOR DTC
EC-23
[QR (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
EC

*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by ISO 15031-5.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: When engine is running
*5: The troubleshooting for this DTC needs CONSULT-II.
*6: For models with ESP system
*7: When the fail-safe operations for both self-diagnoses occur, the MI illuminates.
*8: For QR25DE engine modelsP1128 1128 ETC MOT 1×EC-314
P1143 1143 HO2S1 (B1) 2×EC-322
P1144 1144 HO2S1 (B1) 2×EC-328
P1146 1146 HO2S2 (B1) 2×EC-334
P1147 1147 HO2S2 (B1) 2×EC-342
P1211 1211
TCS C/U FUNCTN*62—EC-350
P1212 1212
TCS/CIRC*62—EC-351
P1217 1217 ENG OVER TEMP 1×EC-352
P1225 1225 CTP LEARNING 2 —EC-368
P1226 1226 CTP LEARNING 2 —EC-370
P1229 1229 SENSOR POWER/CIRC 1×EC-372
P1564 1564
ASCD SW*81—EC-377
P1572 1572
ASCD BRAKE SW*81—EC-387
P1574 1574
ASCD VHL SPD SEN*81—EC-396
P1610 - P1615 1610 - 1615 NATS MALFUNCTION 2 —BL-108
P1705 1705 TP SEN/CIRC A/T 1×AT-173
P1706 1706 P-N POS SW/CIRCUIT 2×EC-398
P1720 1720 V/SP SEN (A/T OUT) 2 —EC-403
P1760 1760 O/R CLTCH SOL/CIRC 2×AT-178
P1805 1805 BRAKE SW/CIRCUIT 2 —EC-405
P2122 2122 APP SEN 1/CIRC 1×EC-409
P2123 2123 APP SEN 1/CIRC 1×EC-409
P2127 2127 APP SEN 2/CIRC 1×EC-416
P2128 2128 APP SEN 2/CIRC 1×EC-416
P2135 2135 TP SENSOR 1×EC-424
P2138 2138 APP SENSOR 1×EC-432
DTC*1
Items
(CONSULT-II screen terms)TripMI lighting
upReference page
CONSULT-II
GST*
2ECM*3