mirror NISSAN X-TRAIL 2005 Service Owner's Guide

GW-92
DOOR MIRROR

Disassembly and AssemblyEIS004JS
DISASSEMBLY
1. Pull out all the terminals from the connector.
NOTE:
Before pulling out the terminal, note the connector terminal arrangement.
2. Turn the mirror glass surface upward.
3. Apply a protective tape to the housing.
4. Insert a narrow slotted screwdriver in the concave gap between mirror glass and power unit to push up
tabs (2 locations) on mirror holder to disengage lower part of mirror holder, and remove mirror body
assembly.
NOTE:
When pushing up the tabs, do not forcefully push up only 1 concave but try to push up using 2 concave
positions.
5. Remove packing.
6. Remove base.
7. Remove electric retracting unit.
8. Remove power unit, and disconnect the connector.
9. Separate the electric retracting unit from the bracket.
1. Mirror body 2. Power unit 3. Bracket
4. Electric retracting unit 5. Housing 6. Base
7. Packing 8. Connector
SIIA0187E

DOOR MIRROR
GW-93
C
D
E
F
G
H
J
K
L
MA
B
GW

ASSEMBLY
1. Install bracket to the electric retracting unit.
2. Connect power unit connector. Install electric retracting unit (bracket).
3. Install electric retracting unit and base to the housing.
4. Place power unit and mirror body assembly in a horizontal position.
5. Engage upper tabs of mirror glass with power unit. Then, press lower part of mirror glass down until the
lower part snaps to allow engagement of lower tabs.
NOTE:
After installation, visually check that the lower tabs (2) are securely engaged when viewed from the bot-
tom of mirror surface.
6. Install the packing to the base.
7. Insert the harness terminal into the connector.
NOTE:
Make sure to insert the harness terminal into the correct connector. Do not confuse the locations.

GW-94
INSIDE MIRROR

INSIDE MIRRORPFP:96321
Removal and InstallationEIS008O4
REMOVAL
Remove the screws securing inside mirror assembly and mirror base
as shown in the figure.
INSTALLATION
Install in the reverse order of removal.
SIIA1024E

EI-22
DOOR OUTSIDE MOLDING

DOOR OUTSIDE MOLDING PFP:82820
Removal and InstallationEIS0015E
REMOVAL
Front door outside molding
1. Roll the front door window all the way up.
2. Remove front door finisher. Refer to EI-32, "
Removal and Installation" .
3. Remove corner cover and door mirror. Refer to GW-91, "
Removal and Installation" .
4. Disengage front door outside molding pawl.
5. Reaching from inner side of door, use a clip clamp tool to disen-
gage front door outside molding from the pawl.
NOTE:
Insert clip clamp tool into the door tab, then disengage by press-
ing in the direction of arrow. (See figure on the right.)
Rear door outside molding
1. Roll the rear door window all the way up.
2. Remove rear door finisher. Refer to EI-32, "
Removal and Installation" .
3. Remove corner inner cover and corner outer cover. Refer to GW-83, "
Removal and Installation" .
4. Disengage rear door outside mold pawl.
SIIA0201E
SIIA0202E

HEADLINING
EI-39
C
D
E
F
G
H
J
K
L
MA
B
EI

HEADLININGPFP:73910
Removal and InstallationEIS000ND
REMOVAL
1. Remove front pillar and center pillar garnishes. Refer to EI-35, "Removal and Installation" .
2. Remove body side welt. Refer to EI-35, "
Removal and Installation" .
3. Remove rear pillar finisher. Refer to EI-35, "
Removal and Installation" .
SIIA0223E
1. Headlining (standard) 2. Sun-visor (left) 3. Sun-visor (right)
4. Sun-visor holder 5. Inside mirror 6. Inside mirror cover
7. Map lamp 8. Interior lamp 9. Assistance grip (fixed type)
10. Luggage compartment lamp 11. Headlining (sunroof) 12. Sunroof switch and map lamp
13.Assistance grip (retractable
type)14. Sunroof welt

EI-40
HEADLINING

4. Remove assistance grip.
NOTE:
When removing the assistant's grip cover from a car with a sun-
roof, use a clip clamp tool to disengage the upper and lower
tabs, then slide inwards and remove screws (1 each on left/
right).
5. Remove map lamp, interior lamp, and luggage compartment lamp. Refer to LT- 1 5 0 , "
Removal and Instal-
lation" and LT- 1 4 3 , "Removal and Installation" .
6. Remove inside mirror cover.
7. Remove mounting screw on inside mirror.
8. Remove sun visors (driver side and passenger side).
9. Remove headlining rear clips.
10. Remove sun visor holder.
NOTE:
Insert a screwdriver into the cutout and rotate 90° to remove.
11. Remove headlining through the back door opening.
CAUTION:

Always remove or install in a pair.

Cover surroundings with waste to avoid scratches or
damages.

Do not bend headlining too hard.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When installing, insert the protrusions on the headlining into
the holes in the upper part of center pillar.
SIIA0052E
SIIA0224J
PIIA0561E

LT-122
ILLUMINATION

ILLUMINATIONPFP:27545
System Description EKS003C7
Power is supplied at all times

through 10A fuse (No. 31, located in fuse and fusible link box)

to lighting switch terminal 11.
The lighting switch must be in the 1ST or 2ND position for illumination.
The following chart shows the power and ground connector terminals for the components included in the illu-
mination system.
Component Connector No. Power terminal Ground terminal
Headlamp washier switch M23 4 3
Headlamp aiming switch M24 3 4
ESP off switch M25 3 4
Driving lamp switch M101 1 5
Door mirror remote control switch M26 10 3
Driver pocket lamp M119 1 2
4WD mode switch M39 5 6
Hazard switch M51 7 8
Rear window defogger switch M50 5 6
A/C auto amp. M52 12 11
Combination meter M45 60 63
Heater control panel M55 2 6
Audio unit (with cassette deck) M108 8 case ground
Audio unit (without cassette deck and
with NAVI)M47 1 case ground
Audio unit (without cassette deck and
without NAVI)M207 1 case ground
Cigarette lighter socket M301, M302 3 2
Ashtray illumination M303 5 6
A/T device M58 3 4
NAVI control unit M116, M117 25 1, 4
NAVI switch M113 2 3
Heated seat switch LH (LHD models) B212 5 6
Heated seat switch RH (LHD models) B213 5 6

PG-66
HARNESS

ESP BRC ESP/TCS/ABS Control System
ETC1 EC Electric Throttle Control Function
ETC2 EC Electric Throttle Control Motor Relay
ETC3 EC Electric Throttle Control Motor
F/FOG LT Front Fog Lamp
F/PUMP EC Fuel Pump
FIAR EC Fuel Injector Adjustment Resistor
FRO2 EC Front Heated Oxygen Sensor
FRO2/H EC Front Heated Oxygen Sensor Heater
FRPS EC Fuel Rail Pressure Sensor
FTP EC Fuel Transport Pump
FTS AT A/T Fluid Temperature Sensor Circuit
FTS EC Fuel Temperature Sensor
FUEL EC Fuel Injection System Function
GLORLY EC Glow Relay
GLOW EC Glow Control System
H/AIM LT Headlamp Aiming Control System
H/LAMP LT Headlamp
HEATER MTC Heater System
HLC WW Headlamp Cleaner
HO2S1 EC Heated Oxygen Sensor 1
HO2S1H EC Heated Oxygen Sensor 1 Heater
HO2S2 EC Heated Oxygen Sensor 2
HO2S2H EC Heated Oxygen Sensor 2 Heater
HORN WW Horn
HSEAT SE Heated Seat
IATS EC Intake Air Temperature Sensor
IATSEN EC Intake Air Temperature Sensor
IGNSYS EC Ignition System
ILL LT Illumination
INJ/PW EC Fuel Injector Power Supply Circuit
INJECT EC Fuel Injector
INT/L LT Map Lamp
IVC EC Intake Valve Timing Control Solenoid Valve
KS EC Knock Sensor
LOAD EC Electrical Load Signal
LPSV AT Line Pressure Solenoid Valve
MAFS EC Mass Air Flow Sensor
MAIN AT Main Power Supply and Ground Circuit
MAIN EC Main Power Supply and Ground Circuit
METER DI Speedometer, Tachometer, Temp. and Fuel Gauges
MIL/DL EC MIL & Data Link Connector
MIRROR GW Door Mirror
MULTI BL Multi-Remote Control SystemCode Section Wiring Diagram Name

MA-4
DESCRIPTION

DESCRIPTIONPFP:00000
Pre-Delivery Inspection ItemsELS000Y5
Shown below are Pre-delivery Inspection Items required for the new vehicle. It is recommended that
necessary items other than those listed here be added, paying due regard to the conditions in each
country.
Perform applicable items on each model. Consult text of this section for specifications.
Install vehicle protection kit
Fit all accessories ordered (if applicable) (e.g. towbar, audio, navigation, air conditioner, styling kit)
UNDER HOOD — engine off
Check coolant level and cooling system for leaks
Charge battery and check terminals for condition
Check drive belts tension (diesel only)
Check fuel filter for water or dust (diesel only) and fuel system for leaks
Check engine oil level and for oil leaks
Check brake and clutch fluid levels and fluid lines for leaks
Check and top up washer reservoirs
Check power steering fluid level and fluid lines for leaks (if applicable)
Check air conditioning system for gas leaks (if applicable)
ON INSIDE AND OUTSIDE
Install transit fuse if removed for vehicle storage
Check instruments, gauges, lamps, horn and accessories for operation
Check wipers and washers for operation and adjustment
Check interior and door mirrors and sun visors for operation
Set radio code and set clock
Check parking brake adjustment
Check clutch pedal adjustment
Check steering lock operation
Check seat adjusters and seat belts for operation
Check all windows for operation and alignment
Check mouldings, trim and fittings for fit and alignment
Check weatherstrips for fit and adhesion
Check hood, trunk lid, door panels and fuel lid for fit and alignment
Check latches, keys, remote key, door locks and remote trunk lid and fuel lid release for operation
Check wheel nut torques
Check tyre pressure (incl. spare tyre)
Check tool kit and jack for operation
Check automatic transmission/transaxle starter inhibitor (if applicable)
Check sunroof for operation and alignment (if applicable)
UNDER BODY
Check manual transmission/transaxle, differential and transfer box for oil level and oil leaks
Tighten bolts and nuts steering linkage and gear box, axle/suspension parts, propeller and exhaust system
Check brake and clutch lines, and oil/fluid reservoirs for leaks
Remove front suspension spacer blocks (if applicable)
Check body mounting torque (if applicable)

IDX-4
ALPHABETICAL INDEX
EM-73
Cylinder head bolt tightening(YD22DDTi) ....... EM-211
Cylinder head gasket selection(YD22DDTi) ... EM-212
Cylinder head(QR20DE-QR25DE) ................... EM-70
Cylinder head(YD22DDTi) .............................. EM-209
D
Data link connector ............................ EC-518
, EC-958
Data link connector for Consult ......... EC-105, EC-606,
EC-1034
, EC-1405
DEF - Wiring diagram ....................................... GW-21
Desiccant Assembly ...................................... ATC-156
Diagnosis sensor unit ..................................... SRS-41
Diagnostic trouble code (DTC) ...................... EC-1372
Diagnostic trouble code (DTC) for OBD system EC-19,
EC-55
, EC-533, EC-565, EC-973, EC-998, EC-1351
Diagnostic trouble code (DTC) inspection priority chart
EC-77
, EC-576, EC-1010, EC-1381
Differential gear (FF M/T) ..................... MT-26, MT-44
DLC - Wiring diagram ........................ EC-518, EC-958
Door glass ........................................... GW-80, GW-83
Door glass Fitting Adjustment ............. GW-80, GW-83
Door lock ................................................. BL-91, BL-95
Door mirror ........................................................ GW-86
Door trim ............................................................. EI-32
Door, front .......................................................... BL-18
Door, rear ........................................................... BL-18
Drive belt inspection(QR20DE-QR25DE) ......... MA-20
Drive belt inspection(YD22DDTi) ...................... MA-29
Drive belt(QR20DE-QR25DE) .......................... EM-13
Drive belt(YD22DDTi) ..................................... EM-140
Drive shaft (front) ............................................. FAX-11
Drive shaft (rear) ............................................. RAX-14
Driver air bag .................................................. SRS-30
Dropping resistor (A/T) ...................... AT-160, AT-393
DTC work support ............................................ EC-112
Dual pressure switch ........ ATC-18, ATC-95, ATC-158
Duct and grilles ............................... ATC-137, MTC-33
E
ECM input/output signal ....................... EC-95
, EC-595
ECM power supply EC-125, EC-286, EC-625, EC-719
ECM/PW - Wiring diagram ................. EC-287, EC-720
ECTS - Wiring diagram .... EC-167, EC-654, EC-1095,
EC-1451
EGR function ................ EC-1186, EC-1193, EC-1651
EGR volume control valve ............ EC-1186, EC-1193,
EC-1651
EGRC/V - Wiring diagram ............. EC-1188, EC-1195,
EC-1653
Electric sunroof .................................................. RF-10
Electric throttle control actuator ........ EC-294, EC-296,
EC-314
, EC-723, EC-726, EC-745
Electrical load signal circuit ................ EC-480, EC-920
Electrical unit ..................................................... PG-76
Electrical units location ...................................... PG-69
Electronic ignition (EI) system ............. EC-37, EC-550
Engine control circuit diagram ........... EC-93, EC-593,
EC-1025
, EC-1396
Engine control component parts location .......... EC-88,
EC-588
Engine control module (ECM) .......... EC-283, EC-716,
EC-1227
, EC-1229, EC-1566, EC-1568
Engine control system diagram and chart ........ EC-30,
EC-543
, EC-984, EC-1360
Engine coolant temperature sensor (ECTS) ... EC-165,
EC-652
, EC-1093, EC-1449
Engine coolant(QR20DE-QR25DE) .................... CO-9
Engine coolant(YD22DDTi) .............................. CO-32
Engine fail-safe system ....................... EC-78, EC-577
Engine oil filter replacement(QR20DE-QR25DE) .........
MA-25
Engine oil filter replacement(YD22DDTi) MA-36, MA-37
Engine oil precautions .......................................... GI-7
Engine oil replacement(QR20DE-QR25DE) ..... MA-24
Engine oil replacement(YD22DDTi) .................. MA-35
Engine oil(QR20DE-QR25DE) ............................. LU-7
Engine oil(YD22DDTi) ....................................... LU-20
Engine removal(QR20DE-QR25DE) ................. EM-81
Engine removal(YD22DDTi) ........................... EM-222
ETC1 - Wiring diagram ..................... EC-297, EC-728
ETC2 - Wiring diagram ..................... EC-308, EC-739
ETC3 - Wiring diagram ..................... EC-315, EC-746
EVAP canister purge volume control solenoid valve ....
EC-269
, EC-522, EC-884, EC-962
EVAP vapor lines inspection(QR20DE-QR25DE) ........
MA-28
Evaporative emission (EVAP) system EC-522, EC-962
Evaporator .................................................... ATC-158
Exhaust manifold(QR20DE-QR25DE) .............. EM-25
Exhaust manifold(YD22DDTi) ......................... EM-151
Exhaust system ................................................... EX-2
Exhaust system inspection ..................... EX-2, MA-39
Expansion valve ............................................ ATC-159
Exterior EI-21, EI-22, EI-24, EI-25, EI-26, EI-27, EI-28,
EI-30
, EI-31
F
F/FOG - Wiring diagram ..................... LT-108
, LT-109
F/PUMP - Wiring diagram EC-467, EC-907, EC-1270,
EC-1609
Fan control amp. ............................. ATC-84, ATC-129
Fan switch ....................................................... MTC-18
FIAR - Wiring diagram .................. EC-1253, EC-1592
Final drive (FF M/T) .............................. MT-26, MT-44
Finisher, interior - See Trim ................................ EI-32
Finisher, rear panel ............................................. EI-31
Floor trim ............................................................. EI-38
Flow charts ......................................................... GI-23
Fluid temperature sensor (A/T) ........................ AT-111
Fluorescent leak detector ............................. ATC-160
Flywheel (clutch) ................................................ CL-16
Flywheel runout(QR20DE-QR25DE) .............. EM-116
Flywheel runout(YD22DDTi) ........................... EM-255
Fog lamp, front ................................................. LT-108